Related Manuals for Zephyr Trapeze CTP-E 48SX
Summary of Contents for Zephyr Trapeze CTP-E 48SX
- Page 1 Trapeze CTP-E 48SX CTP-E54SX CTP-E 60SX Model number: Serial number: Date of Purchase: Sales Dealer: MAY07.0101 © Zephyr Corporation. www.zephyronline.com...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ... LIST OF MATERIALS ... INSTALLATION Ducting Calculation Sheet ... Mounting Height and Clearance ... Ducting ... Specifications ... Internal Blower ... Preparing Hood for External Blower ... Mounting the Hood ... FEATURES & CONTROLS Controls Overview ... MAINTENANCE Cleaning ...
- Page 4 To Reduce the Risk of Fire and Electric Shock, Install This Range Hood Only with Remote Blower Models C B E-1000 Rated Maximum 6.2 amp, 120 Vac 60Hz or Integral Blowers Manufactured by Zephyr Ventilation, Models C B I-600. www.zephyronline.com...
- Page 5 MODEL: CTP-ExxS 1 - Hood 2 - Baffle Filters 4 - G U-10, 120V 50 W, halogen bulbs 2 - Utensil Rails 2 - Telescopic Duct Covers 4 - Telescopic Rods Sets 4 - Angle Bra ckets (27 3/8”) 4 - Angle Bra ckets (35 3/8”) 1 - Ceiling MountingBra cket 1 - Internal Flange 1 - Motor Housing...
- Page 6 Equivalent number Duct pieces length x used 3 1/4” x 10” 1 Ft. Rect., straight 7” Round, 1 Ft. straight 7” Round, 1 Ft. straight 3 1/4” x 10” 15 Ft. Rect. 90 elbow 3 1/4” x 10” 9 Ft. Rect.
-
Page 7: Damage - Shipment/Installation
Min 34"-Max 52" 9" Min 28"-Max 36" Min 98"-Max 124” 36" DUCTING A minimumof 6” round or 3-1 /4 x 10" rectangular duct work must be used to maintain maximumair flow efficiency with the 600 cfm internal blower. A minimumof 10” to 8” round must be used with the 1000 cfm external blower. - Page 8 WARNING FIRE HAZARD NEV E R exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling,attics or garages. All exhaust must be ducted to the outside. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or DuctTape. Some Ducting Options: side wall cap w/ gravity damper...
- Page 9 9“ 32“ 15 3/4” 26 5/8” 32” 11 3/4“ 10“ 9“ 2” Min 21” - Max 40” 7/64” 12 1/8” 13/32” 2” 48” , 54” , 59 1/8”...
- Page 10 ATTENTION The following are intructions for installing internal blower model CBI-600. For instructions on preparing for external blower model CBE-1000 please turn to page “10”. Before installing, verify that motor spins freely. The internal blower kit consists of the blower and capacitor box with wiring.
- Page 11 6. Attach junction box to internal flange using provided 1/2” self tapping screws and 4mm internal diameter washers. 8. Place blower with attached flange into motor housing as shown on Fig-A. 10. Att ach other end of capacitor box connector and junction box connector to control board box and wiring box connector inside hood.
- Page 12 ATTENTION The following are instructions on preparing your hood for installation with external blower model CBE-1000. For instructions on installing internal blower model CBI-600 please turn to page “8”. The external blower kit consists of an 8” collar, external flange and external blower wiring box.
-
Page 13: E L E Ctrical - Warning
Tabs Add Blockings Ceiling Bracket Using the cardboard template from top of box, mark the center point in between the (4) mounting holes. Determine the location for mounting your hood, place template on ceiling and mark/drill the center point for the ceiling mounting bracket and the foud corner holes where the telescopic rod couplers will attach to the ceiling. - Page 14 1. Mount motor housing to the range hood b ody using (10) 1/2” self tapping screws. 2. Determine height of hood, measure and select either 27 3/8” or 35 3/8” angle brac them to the motor housing using (8) 1/2” self tapping screws (2) for each angle bracket. 3.
- Page 15 5. Lift assembled unit and attach all (4) angle brackets to ceiling bracket. Make sure the tabs on each angle brackets are facing the outside. The angle brackets will fit between the slots on the ceiling bracket. One half of the angle bracket will be on the outside of the ceiling bracket and the other half will be on the inside of the ceiling bracket.
- Page 16 Telescopic Rod Installation 1. Install telescopic rod (thicker end down) into coupler on top of hood and secure with medium set screw. Attach screw using provided tool. 2. Extend telescopic rod towards the ceiling and insert thin end of rod into ceiling coupler. Attach a medium set screw in the middle where the two rods attach to each other.
- Page 17 1. Blower On/Off By pressing , the blower is switched On and Off. 2. Speed Selection The 3 speed levels are selected by presing level selected. 3. Delay Off This is used for programmed shut down of blower and lights 15 minutes after the function is activated. Press a dot flashes in the lower right hand side of display in 15 minutes.
-
Page 18: Re-Setting Function
Filter Clean Reminder (Standard Baffle Filters fitted): A set of baffle filters are fitted by the factory. These Baffle Filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean. The Filter Clean Reminder function in the microprocessor will automatically indicate by a flashing when the metal filters need to be cleaned after... -
Page 19: Surface Maintenance
Remove filters by sliding away from center of hood and pulling down. Dry filters and re-install before using hood. Replacing Baffle Filters Should filters wear out due to age and prolonged use, contact Zephyr to purchase replacements. www.zephyronline.com Handles... - Page 20 R eplacing Light Bulbs: CAUTION: Light bulbs become extremely hot when turned on. DO NOT touch bulbs until switched off and cooled. Touching hot bulbs may cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove bulb by pressing both ends of the metal retaining clip together, the light socket will now extend from the hood allowing you to remove the bulb.
- Page 21 s s I After installation, the unit 1. The power source is not turned ON. doesn’t work? 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected. 4.
- Page 22 www.zephyronline.com Part Description Part # Accessory Description Part #...
- Page 23 Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instruc- tions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr's Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses.