Related Manuals for Zephyr COK-E36SX
Summary of Contents for Zephyr COK-E36SX
- Page 1 Okeanito CO K-E36SX CO K-E42SX CO K-E48SX Model number: Serial number: Date of Purchase: Sales Dealer: © Zephyr Corporation. MAY07.0101 www.zephyronline.com...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ... LIST OF MATERIALS ... INSTALLATION Ducting Calculation Sheet ... Mounting Height and Clearance ... Ducting ... Specifications ... Internal Blower ... Preparing Hood for External Blower ... Mounting the Hood ... FEATURES & CONTROLS Controls Overview ... MAINTENANCE Cleaning ...
- Page 4 To Reduce the Risk of Fire and Electric Shock, Install This Range Hood Only with Remote Blower Models C B E-1000 Rated Maximum 6.2 amp, 120 Vac 60Hz or Integral Blowers Manufactured by Zephyr Ventilation, Models C B I-600. www.zephyronline.com...
- Page 5 MODEL: COK-ExxS 1 - Hood 1 - Baffle Filter (2 on 48” model) 2 - 50W 120V Halogen Light Bulbs GU-10 2 - 40W 120V Appliance Bulbs 1 - Utensil Rail 2 - Telescopic Duct Covers 1 - Ceiling Mounting Bracket (pre attached to duct cover) 1 - Wall Mounting Bracket 1 - HARDWARE PACKET 7 - 2”...
- Page 6 Equivalent number Duct pieces length x used 3 1/4” x 10” 1 Ft. Rect., straight 7” Round, 1 Ft. straight 7” Round, 1 Ft. straight 3 1/4” x 10” 15 Ft. Rect. 90 elbow 3 1/4” x 10” 9 Ft. Rect.
-
Page 7: Damage - Shipment/Installation
Min 32"-Max 52" 14 1/2" Min 96"-Max 124” Min 28"-Max 36" 36" DUCTING A minimum of 6” round or 3-1/4 x 10" rectangular duct work must be used to maintain maximum air flow efficiency with the 600 cfm internal blower . A minimum of 10"to 8” round must be used with the 1000 cfm external blower. - Page 8 www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics, or garages. All exhaust must be ducted to the outside. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or DuctTape. Some Ducting Options: External Roof Pitch w/...
- Page 9 19 3/4” 10” 19 3/4” 36” , 42” , 48” 6" 8 5/16” 9 3/16” 16 5/8” 13 3/8” 95° 11 7/8” 22 5/8” 5" - 36" 8"- 42" 3 1/2"-48" 15” 14 1/2”...
- Page 10 ATTENTION The following are intructions for installing internal blower model CBI-600. For instructions on preparing for external blower model CBE-1000 please turn to page “10”. Before installing, verify that motor spins freely. The internal blower kit consists of the blower and capacitor box with wiring.
- Page 11 5. Remove existing grounding screw and attach grounding wire from capacitor box. 7. Attach short capacitor connector to blower connector. 9. Use plastic tie to hold wiring together. Continue to page “12” for hood installation instructions. 6. Re-attach grounding screw to finish installation of capacitor box.
- Page 12 ATTENTION The following are intructions on preparing your hood for installation with external blower model CBE-1000. For instructions on installing internal blower model CBI-600 please turn to page “8”. NOTE: Please refer to the CBE-1000 manual for external blower mounting instructions. The external blower kit consists of an 8”...
- Page 13 6. Position cover onto external blower wiring box. 8. Attach connector from external blower wiring box to control board box connector inside hood. 10. Final view of external blower preparation 7. Secure cover to box with provided screw. 9. Attach grounding wire from external blower wiring box to grounding screw of the junction box.
- Page 14 Duct Cover Ceiling Bracket 21” 7 1/2” 1. Measure from cooking surface to hood bottom, level and mark line A. 2. Plum and mark center line. 3. Mark mounting height, line B (14 1/2” from line A). This is the top of the hood. 4.
- Page 15 gap between bracket and wall Bottom Attach screws to both sides of the duct cove rs and secure to ceiling bracket. 1. Place wall bracket on line C. Position top of wall bracket so it is even with the 21” mounting spread. Make sure bracket is attached to wall as shown in the diagram.
- Page 16 1. Attach utensil rail to hood canopy. A small hole has been pre-drilled into the canopy to provide a starting point to attach the first utensil rail post. After the first post is lined up with the hole, gently slide the rest of the rail onto the canopy.
- Page 17 Blower On/Off Display Adjust 3 Speed Levels 1. Blower On/Off By pressing , the blower is switched On and Off. 2. Speed Selection The 3 speed levels are selected by pressing The display indicates level selected. 3. Delay Off This is used for programmed shut down of blower and lights 15 minutes after the function is activated. Press once, a dot flashes in the lower right hand side of display The hood will completely shut down in 15 minutes.
-
Page 18: Re-Setting Function
Filter Clean Reminder (Standard Baffle Filters fitted): A set of baffle filters are fitted by the factory. These Baffle Filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean. The Filter Clean Reminder function in the microprocessor will automatically indicate by a flashing when the metal filters need to be cleaned after... -
Page 19: Surface Maintenance
Dry filters and re-install before using hood. ReplacingBaffle Filters Should Should filters filters wear wear out out due due to to age age and and prolonged prolonged use, contact Zephyr to purchase replacements. www.zephyronline.com 12 3/4” ” 15” 15” (Fig. 1) Handles... - Page 20 Replacing Light Bulbs: CA UTION: Light bulbs become extremely hot when turned on. DO NOT touch bulbs until switched off and cooled. Touching hot bulbs may cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove bulb by pressing both ends of the metal retaining clip together, the light socket will now protude from the hood allowing you to remove the bulb.
- Page 21 s s I After installation, the unit 1. The power source is not turned ON. doesn’t work? 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected. 4.
- Page 22 Part Description Accessory Description Part# Part# www.zephyronline.com...
- Page 23 Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instruc- tions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr's Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses.