Related Manuals for Zephyr Shade CSH -E42SX
Summary of Contents for Zephyr Shade CSH -E42SX
- Page 1 Shade CSH -E36SX CSH -E42SX CSH -E48SX Model number: Serial number: Date of Purchase: Sales Dealer: MAY07.0101 © Zephyr Corporation.
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ..........LIST OF MATERIALS ........INSTALLATION Ducting Calculation Sheet ....... Mounting Height and Clearance ..... Ducting ..............Specifications ............Internal Blower ............ 8 - 9 Preparing Hood for External Blower ....10 - 11 Mounting the Hood ..........12 - 13 FEATURES &...
- Page 4 CAUTION To Reduce the Risk of Fire and Electric Shock, Install This Range Hood Only with Remote Blower Models C B E-1000 Rated Maximum 6.2 amp, 120 Vac 60Hz or Integral Blowers Manufactured by Zephyr Ventilation, Models C B I-600.
- Page 5 MODEL: CSH-ExxSX 1 - Hood Body 2 - Baffle Filters (1 - 36” model) 4 - GU-10, 120V, 50W Halogen Bulbs 1 - Hood Door 2 - Telescopic Duct Covers 1 - Ceiling Mounting Bracket 1 - HARDWARE PACKET 7 - 2” wood screws 7 - anchors 7 - 1/2”...
- Page 6 www.zephyronline.com Equivalent number Equivalent number Duct pieces Duct pieces length x used Total length x used Total 3 1/4” x 10” 1 Ft. 6” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6” Round, 30 Ft. straight roof cap 7”...
- Page 7 Minimum mount height between range top to hood bot- tom should be no less than 24". Maximum mount height should be no higher than 32". Min 36"- Max 40" It is important toinstall the hood at the proper mounting height. Hoods mountedtoo low could result in heat damage and fire hazard;...
- Page 8 www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics, or garages. All exhaust must be ducted to the outside. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or DuctTape. Some Ducting Options: External Roof Pitch w/...
- Page 9 16 7/8” 12” 10” 8“-12" 20" 31 1/4” 8" 10” or 24” 30", 36”, 42” DOOR INSERT PANEL 1/8” (3.175 mm) thickness 24 5/8” (625mm) 35 7/16”, 41 7/32”, 47 1/4” 36 inch-31 5/6" 42 inch-36 13/16” 48 inch-42 7/8” 8 5/16”...
- Page 10 www.zephyronline.com ATTENTION The following are intructions for installing internal blower model CBI-600. For instructions on preparing for external blower model CBE-1000 please turn to page “10”. Before installing, verify that motor spins freely. The internal blower kit consists of the blower 1.
- Page 11 5. Remove existing grounding screw and 6. Re-attach grounding screw to finish attach grounding wire from capacitor box. installation of capacitor box. Refer to Fig-A on previous page. 7. Attach short capacitor connector to blower 8. Att ach long capacitor connector to control connector.
- Page 12 www.zephyronline.com ATTENTION The following are intructions on preparing your hood for installation with external blower model CBE-1000. For instructions on installing internal blower model CBI-600 please turn to page “8”. NOTE: Please refer to the CBE-1000 manual for external blower mounting instructions. The external blower kit consists of an 8”...
- Page 13 6. Position cover onto external blower 7. Secure cover to box with provided screw. wiring box. 8. Attach connector from external blower 9. Attach grounding wire from external blower wiring box to control board box connector wiring box to grounding screw of the junction inside hood.
- Page 14 www.zephyronline.com Duct Cover Ceiling Bracket Duct Cover Ceiling Bracket 20” 24” 16 1/4” min 24” max 32” Attach screws to ceiling bracket 1. Measure from cooking surface to hood bottom, level and mark line A. 2. Plum and mark center line. 3.
- Page 16 www.zephyronline.com 1. Blower On/Off By pressing , the blower is switched On and Off. 2. Speed Selection The 3 speed levels are selected by presing to decrease and to increase speed level. T he display indicates level selected. 3. Delay Off This is used for programmed shut down of blower and lights 15 minutes after the function is activated.
- Page 17 Filter Clean Reminder (Standard Baffle Filters fitted): A set of baffle filters are fitted by the factory. These Baffle Filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean. The Filter Clean Reminder function in the microprocessor will automatically indicate by a flashing when the metal filters need to be cleaned after...
- Page 18 www.zephyronline.com Infrared Receiver / Transmitter: By aiming the infrared transmitter (located at the top of the remote control) to the infrared receiver (located on the bottom of the range hood) you can control the following features remotely: LightsOn/Off, D im Adjust3 SpeedLevels BlowerOn/Off Lights On/Off/ Dim...
- Page 19 Insert Panel Dimensions: The original stainless steel insert panel may be replaced with any 1/8” fired rated piece of material. The panel dimensions for each model are as follows; Width Height Thickness CSH-E48SX 42 7/8” 24 5/8” 1/8” CSH-E42SX 36 13/16” 24 5/8”...
- Page 20 Remove and clean by hand or in dishwasher. Spray degreasing detergent and leave to soak if heavily soiled. Dry filters and re-install before using hood. Replacing Baffle Filters Should filters wear out due to age and prolonged use, contact Zephyr to purchase replacements. Fig. 1...
- Page 21 www.zephyronline.com Replacing Light Bulbs: CA UTION: Light bulbs become extremely hot when turned on. DO NOT touch bulbs until switched off and cooled. Touching hot bulbs may cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove bulb by pressing both ends of the metal retaining clip together, the light socket will now protude from the hood allowing you to remove the bulb.
- Page 22 www.zephyronline.com s s I After installation, the unit 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. doesn’t work? 2. The power line and the cable locking connector is 2.
- Page 23 Part Descr iption Part# Halogen Bulb G U-10, 120V, 50W Z0B-0020 Accessory Descr iption Part# Internal Blower, 600 cfm CBI-600 External Blower, 1000 cfm CBE-1000 Duct Cover Extension Kit Z1C-00SH...