HAMPTON BAY H27-NG10 Owners & Installation Manual page 23

3) Attach the 4" dia. flex liner to the vent ter-
minal ensuring that the flex overlaps the
collar of the vent terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal
and secure with 3 of the #8 x 1/2" screws
(stainless steel).
4) Attach the adjustable pipe section to the
vent terminal using Mill-Pac attach with 3
of the #8 x 1/2" screws (stainless steel).
NOTE: For best results and optimum perfor-
mance with each approved venting
system, it is highly recommended to
apply "Mill-Pac" sealant (supplied) to
every inner pipe connection. Failure
to do so may result in drafting or
performance issues not covered
under warranty.
Note: The pipe seam should be
facing down.
Note: To make the installation more aes-
thetically pleasing, we recommend
framing out a square that the cap
can be mounted on.
Note: If installing ter-
mination on a
siding covered
wall, a vinyl sid-
ing standoff or
f ur ri n g s tri p s
must be used to
ensure that the
termination is not
recessed into the
siding. For vinyl siding standoff
installation refer to the Dura-Vent
Termination instructions.
5) Slide the partially connected pipe and
vent terminal assembly through the wall
thimbles (from the exterior into the interior)
and secure the cap to the exterior wall with
4 of the supplied screws (#8 x 1-1/2" drill
point, stainless steel). Note: pilot holes will
need to be drilled through the wall thimble
on all 4 corners.
Note: The four screws provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6) A bead of non-hardening mastic should
be run around both the termination and
vinyl siding standoff to prevent water from
entering and to make a tight seal between
the cap and the standoff.
7) Stretch the 4" dia. flex liner out fully and get
a trial fit of the liner onto the 4" dia. starter
collar.
8) Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length,
this will make the final assembly easier to
work with.
9) Secure the 4" dia. flex liner to the 4" adapter
installation
with Mill-Pac and 3 of the #8 x 1/2" screws
(stainless steel).
10) Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8
x 1-1/2" drill point, black) to the wall.
11) Slide the 90
elbow and the 4 ft. pipe section (crimp end
up) over the 4" dia. flex liner.
12) Install the spring spacers onto the pipe sec-
tions.
13) Secure the 4" dia. flex liner with adapter
onto the stove collar. Put a bead of Mill-Pac
around the appliance adapter and secure
with 3 screws (#8 x 1/2, stainless steel).
14) Attach the 45
by sealing with Mill-Pac securing with 3 of
the #8 x 1/2" (black) screws.
15) Attach the pipe section to the 45
sealing with Mill-Pac securing with 3 of the
#8 x 1/2" screws (black). Pipe seams should
be facing the wall.
16) Attach the 90
by sealing with Mill-Pac securing with 3 of
the #8 x 1/2" screws (black).
17) Slide the adjustable pipe section onto the 90
elbow. Slide the trim collar over the adjust-
able pipe sections to cover the joint of the
telescopic section.) The flex may have to be
compressed back in order for the adjustable
pipe to properly mate to the elbow. Seal with
Mill-Pac secure with 3 of the #8 x 1/2" screws
(black). Pipe seams facing down.
18) Install the trim collar over the starter collar
and secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
Hampton H27-10 Direct Vent Freestanding Gas Stove
®
|
elbow (crimp end up), the 45
o
elbow onto the starter collar
o
elbow by
o
elbow onto the pipe section
o
|
23
o
o
23