Table of Contents
Advertisement
H27 Direct Vent Gas Fireplace
WARNING:
If the information in these instructions are not
followed exactly, a fi re or explosion may result
causing property damage, personal injury or loss
of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable
vapours and liquids in the vicinity of this or any
other appliance.
Installation and service must be performed by
a qualifi ed installer, service agency or the gas
supplier.
Tested by:
918-812
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
MODELS:
H27-NG Natural Gas
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas sup-
plier, call the fi re department.
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.hampton-fi re.com
H27-LP Propane
This appliance may only be
installed in an aftermarket
permanently located, manu-
factured (USA only) or mobile
home, where not prohibited by
local codes.
This appliance is only for use
with the type of gas indicated
on the rating plate. This ap-
pliance is not convertible for
use with other gases, unless
a certifi ed kit is used.
Owners &
Installation Manual
04/12/11
Advertisement
Table of Contents
Related Manuals for HAMPTON BAY Hampton H27-NG
Summary of Contents for HAMPTON BAY Hampton H27-NG
- Page 1 Tested by: Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. 918-812 04/12/11 FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4...
- Page 2 ® HAMPTON Direct Vent Freestanding Gas Stove To the New Owner: Congratulations! You are the owner of a state-of-the-art Hampton ® Gas Stove by REGENCY FIREPLACE PRODUCTS. The H27 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Remote Control ............36 SAFETY LABEL Final Check..............37 Wiring Diagrams ............37 Copy of Safety Label .............4 OPERATING INSTRUCTIONS REQUIREMENTS MA Code - CO Detector..........6 Operating Instructions ..........39 Lighting Procedure ............39 INSTALLATION Shutdown Procedure ...........39 First Fire ..............39 Automatic Convection Important Message ............8 Fan Operation..............39 Specifi... -
Page 4: Safety Label
Alimentation électrique. Ne doit pas être utilisé avec un combustible solide. FPI Fireplace Products International Ltd. Delta, BC, Canada Made in Canada/Fabrique au Canada 918-813 For the State of Massachusetts, installation and repair must be done by a plumber or gasfi tter licensed in the Commonwealth of Massachusetts. -
Page 5: Requirements
REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:... - Page 6 DIMENSIONS ** Shown with optional side shelves. ® Hampton H27 Direct Vent Freestanding Gas Stove...
-
Page 7: Installation
INSTALLATION INSTALLATION BEFORE YOU START YOUNG CHILDREN SHOULD BE CARE- FULLY SUPERVISED WHEN THEY ARE Safe installation and operation of this appliance IN THE SAME AREA AS THE APPLI- requires common sense, however, we are required ANCE. TODDLERS, YOUNG CHILDREN by the Canadian Safety Standards and ANSI Stand- AND OTHERS MAY BE SUSCEPTIBLE ards to make you aware of the following:... -
Page 8: Important Message
INSTALLATION 1) Provide adequate clearances for servicing, IMPORTANT MESSAGE This appliance installation must comply with the proper operation and around the air openings manufacturer's installation instructions and local into the combustion chamber. SAVE THESE codes, if any. In the absence of local codes fol- low the current National Fuel Gas Code, ANSI INSTRUCTIONS 2) The appliance must be installed on a fl... -
Page 9: General Safety Information
INSTALLATION INSTALLATION GENERAL SAFETY CLEARANCES TO CHECKLIST INFORMATION COMBUSTIBLES 1) Locate your appliance. Refer to the following The clearances listed are MINIMUM distances. 1) The appliance installation must conform with sections: Measure the clearance to both the appliance and local Canadian Electrical Code. the chimney connector. -
Page 10: Locating Your Gas Stove
INSTALLATION OPTIONAL FAN 3) Remove the Top Control Panel Assembly LOCATING YOUR by removing the three screws. GAS STOVE INSTALLATION When selecting a location for your stove, ensure Fan Kit Contains: that the clearances listed above are met as well as ensuring that there is adequate accessibility Qty. - Page 11 INSTALLATION 12) Before re-attaching the rear access panel, the valve wires and the 8) Place the blower close to the base of the unit and feed the long red and black wires through the opening of the base of the unit and the fan wires need to be connected.
-
Page 12: Venting Introduction
"Venting Arrangements" section, simply table on next page or FPI Fireplace Products loosen the screws and push the vent restrictor plate International Ltd. Note: These fl ue pipes must not be to the correct position. -
Page 13: Exterior Vent Terminal Locations
INSTALLATION EXTERIOR VENT TERMINAL LOCATIONS Minimum Clearance Requirements Canada Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm) Clearance to window or door that may be opened 12"(30cm) 9" (23cm) Clearance to permanently closed window Vertical clearance to ventilated soffi t located above the terminal within a horizontal distance of 2 feet (61cm) 22"(56cm) 22"(56cm) from the center line of the terminal (check with the local code) -
Page 14: 4" X 6-5/8" Rigid Pipe Cross Reference Chart
INSTALLATION 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Description Selkirk American Metal Security ICC Excel Simpson Metal-Fab™ ® Direct Temp™ Secure- Vent®... - Page 15 Vinyl Siding Standoff for AstroCap Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994). Offset Pipe Selection: Use this table to determine offset pipe lengths.
-
Page 16: Rigid Pipe Venting Systems
® , Selkirk Direct-Temp and ICC Excel. AstroCap is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent Pro are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. ® Hampton H27 Direct Vent Freestanding Gas Stove... -
Page 17: Venting Arrangements
Riser Vent Termination The two diagrams show all allowable com- binations of straight horizontal termination with one 45 elbow off the unit with Snorkels or FPI Riser Vent. Restrictor position "A". Riser Vent Termination Snorkel Termination ® Hampton H27 Direct Vent Freestanding Gas Stove... - Page 18 INSTALLATION Horizontal Venting with Two (2) 90 Elbows One 90 elbow = Two 45 elbows. Option H + H1 With these options, maxi- mum total pipe length is 30 2' Min. 4' Max. feet with minimum of 6 feet 3' Min. 5' Max.
- Page 19 INSTALLATION Vertical Venting with Two (2) 90 Elbows One 90 elbow = Two 45 elbows. Option V V + V1 With these options, max. total pipe length is 30 feet with min. 1' Min. 4' Max. 2' Min. of 6 feet total vertical and max. 2' Min.
-
Page 20: Vertical Termination With Co-Linear Flex System
INSTALLATION VERTICAL TERMINATION WITH CO-LINEAR FLEX SYSTEM THE APPLIANCE MUST NOT BE Masonry chimneys may take various contours which the fl exible liner will accommodate. However, CONNECTED TO A CHIMNEY FLUE keep the fl exible liner as straight as possible, avoid unnecessary bending. SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. -
Page 21: Dv Stove Horizontal Vent Kit
INSTALLATION DV STOVE HORIZONTAL VENT KIT DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (946-216) includes all the parts needed to install the H27 Direct Vent unit with minimum horizontal and vertical vent dimensions. For installations that require longer vertical and/or horizontal vents use the Dura-Vent system as shown in the "Dura-Vent Termination Kit"... - Page 22 INSTALLATION 9) Secure the 4" dia. fl ex liner to the 4" adapter with Mill-Pac and 3 of the #8 x 1/2" screws (stainless steel). 10) Slide the decorative Thimble Cover over the pipe sections and secure with 4 screws (#8 x 1-1/2"...
-
Page 23: Residential And Manufactured Homes / Mobile Home
Simpson Dura-Vent for their wall thimbles, as well for a minimum horizontal termination with the as a square wall thimble cover. FPI Riser Vent Kit. See the diagram for minimum and maximum pipe lengths. When planning your installation, it will be nec-... -
Page 24: Dura-Vent Termination Kit
1 Wall Thimble Cover Part# 640-530/P 1 Horiz. Sq. Term. Cap The FPI AstroCap is certifi ed for installations using FPI venting systems as well as Simpson Dura-Vent® and Direct Vent Pro. The FPI AstroCap is the proprietary trademark of FPI Fireplace Products International Ltd. -
Page 25: Horizontal Terminations
INSTALLATION You will require the following components with your new Direct Vent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer. Note: These are the minimum pieces re- quired. -
Page 26: Vertical
INSTALLATION c) Before connecting the vent pipe to the vent termination, slide the black decorative wall thimble cover over the vent pipe, then slide the Wall Penetration Heat Shield (Part # 946-202) over the vent pipe. Dia. 3. d) Slide the appliance and vent assembly towards the wall carefully inserting the vent pipe into the riser vent terminal assembly. - Page 27 INSTALLATION 7) Ensure vent is vertical and secure the base of the fl ashing to the roof with roofi ng rails, slide storm collar over the pipe section and seal with a mastic. 8) Install the vertical termination cap by twist locking it.
-
Page 28: Converting Class-A Metal Chimney Or
INSTALLATION CONVERTING CLASS-A of the chimney system, and center the The use of an existing chimney as an air intake adaptor on the top of the chimney pipe. METAL CHIMNEY OR is not covered under the ANSI Z21.88a-2007, Drill four 1/8" diameter holes through the CSA 2.33a-2007 test methods and the re- MASONRY CHIMNEY TO adaptor and into the chimney top. -
Page 29: Cathedral Ceilings
INSTALLATION Note: If you are using a 6" square support 7) Ensure vent is vertical and secure the base Since some municipalities have additional local you may fi nd it diffi cult to screw it in of the fl ashing to the roof with roofi ng rails, codes it is always best to consult with your local place because it is fairly small inside. -
Page 30: Aeration Adjustment
INSTALLATION AERATION GAS PIPE 1) Gas on/off knob ADJUSTMENT PRESSURE TESTING 2) Manual high/low adjustment 3) Pilot Adjustment 4) Thermocouple Connection The burner aeration is factory set but may need The appliance must be isolated from the gas sup- adjusting due to either the local gas supply, air sup- ply piping system by closing its individual manual 5) Main Operator ply or altitude. -
Page 31: Conversion From Ng To Lp
INSTALLATION CONVERSION KIT #434-969 FROM NG TO LP THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! NOTE: See page 4 for P33-4 conversion instructions and page 7 for E33S / U32S conversion instructions. Remove burner by removing the 2 Unscrew the pilot orifi... - Page 32 INSTALLATION Turn control knob to the “OFF” position. 12) Using the Allen wrench as shown in 15) Reverse step 2. Fig.4, rotate the screw clockwise until snug, do not overtighten. Remove the black protection cap by 16) Attach the label "This unit has been hand from the high-low knob (Fig.1).
-
Page 33: Installation Of The Dc Sparker
INSTALLATION Remove the stove’s rear panel by unscrew- Installation of the DC Sparker 11) Attach the ground wire to the DC spark ing the two screws. mounting bracket. for the H27 Unit Only: Remove the control panel by unscrewing the 2 screws. 12) Attach the DC sparker generator wires to the DC sparker. -
Page 34: Log Set Installation
INSTALLATION LOG SET INSTALLATION Read the instructions below carefully and refer to the dia- grams. If the logs are broken do not use the unit until they are Place the rear log on the 2 rear log locating pins on the rear replaced. - Page 35 INSTALLATION Take the embers and place on the burner in the space be- Logs must be oriented as shown below. tween the 2 front logs. Do not put embers on the burner in the area between the front logs and the rear log. See photo below.
-
Page 36: Optional Side Shelves Installation
INSTALLATION OPTIONAL SIDE SHELVESIN- REMOTE CONTROL WALL THERMOSTAT STALLATION Use the Hampton ® Remote Control Kit approved A wall thermostat may be installed if desired. for this unit. Use of other systems may void Connect the wires as per the wiring diagrams. 1) Lift off the Cast Top. -
Page 37: Final Check
INSTALLATION CAUTION FINAL CHECK 2) If required, adjusting the primary air to ensure that the fl ame does not carbon. Any alteration to the product that causes First allow the unit to burn for 15 min. to sooting or carboning that results in damage Before leaving this unit with the customer, the stabilize. - Page 38 INSTALLATION PROPANE Units and Units Equipped with DC Spark Boxes* *For installation of the DC Spark Box refer to the LP Conversion instructions in this manual. WARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.
-
Page 39: Operating Instructions
OPERATING INSTRUCTIONS INSTALLATION OPERATING located at the top right hand corner (rear) of INSTRUCTIONS the stove. DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS STILL HOT! 2) Turn gas control knob so indicator points to 1) Read and understand these instructions before Note: When the glass is cold and the appli- operating this appliance. -
Page 40: Copy Of The Lighting Plate Instructions
OPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: A S5601-2004, New Zealand: NZS 5261) WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, or additional information consult a qualified installer, service agency or gas supplier. -
Page 41: Normal Operating Sounds Of Gas Appliances
MAINTENANCE NORMAL OPERATING 2) Clean glass (never when unit is hot), appli- CAUTION: ANY SAFETY SCREEN ance, and door with a damp cloth. Never SOUNDS OF OR GUARD REMOVED FOR use an abrasive cleaner. SERVICING AN APPLIANCE GAS APPLIANCES 3) The heater is fi nished in a porcelain fi nish or MUST BE REPLACED PRIOR TO with a heat resistant paint and should only OPERATING THE APPLIANCE. -
Page 42: Fan Maintenance
MAINTENANCE GENERAL VENT 1) Lift off the Cast Top. MAINTENANCE 5) Lift the Glass Front Assembly up. 6) a) Remove the glass and replace with the Conduct an inspection of the venting system new glass. semi-annually. Recommended areas to inspect as follows: b) Remove logs and replace the newer logs. -
Page 43: Removing Valve
MAINTENANCE 3) Disconnect gas line to stove. 2) Remove the rear access panel on the back 11) Carefully lift the burner tray assembly out. of the stove by removing the 2 screws under 4) Disconnect 3/8" NPT pipe from 90 elbow the rear panel, then lift off the 2 screws at on valve or fl... -
Page 44: Parts List
PARTS LIST MAIN ASSEMBLY Part # Description Part # Description Part # Description 146) 910-794 Power Cord (120 V) 356-101** Casting - Top Fan Air Divider 148) 910-330 Fan Speed Control (120 V) 356-111** Casting - Front 356-121** Casting - Side Right W260260 Top Relief Frame Gasket 149) 904-569... - Page 45 PARTS LIST PARTS LIST MAIN ASSEMBLY ® ® Hampton Hampton H27 Direct Vent Freestanding Gas Stove H27 Direct Vent Freestanding Gas Stove...
-
Page 46: Burner & Log Assembly
PARTS LIST BURNER & LOG ASSEMBLY Part # Description 350-574/P Valve Assembly S.I.T. - Natural Gas 910-478 Valve S.I.T. - Natural Gas / Propane 904-430 #42 Orifi ce - NG. 904-163 #54 Orifi ce - LP 910-190 Piezo Ignitor & Nut 908-672 Control Panel Decal 490-061... -
Page 47: Warranty
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufac- tured. ie. as products evolve, fi eld modifi cations or upgrades will not be performed. - Page 48 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Hampton ® and AstroCap™ are trademarks of FPI Fireplace Products International Ltd. © Copyright 2011, FPI Fireplace Products International Ltd. All rights reserved. Printed in Canada...