Page 1 Software Manual Applicable Models TSP100IIILAN ■ TSP100IIIW ■ TSP100ECO ■ TSP100GT ■ TSP100LAN ■ TSP100U/PUSB ■ Rev. 7.0...
Page 2: Table Of Contents
1.4. Adding a Printer (TSP100IIIW).................... 17 1.4.1. Printer LAN Settings...................... 17 1.4.2. Creating a Printer Queue ....................23 1.5. Adding a Printer (TSP100IIILAN) ..................25 1.5.1. Printer LAN Settings...................... 25 1.5.2. Creating a Printer Queue ....................31 1.6. Uninstallation ........................33 Features ............................
Page 3 4.1.5. elp ..........................80 4.2. Information ........................... 81 4.3. General Settings ........................82 4.3.1. Default Text Settings ..................... 83 4.3.2. Default Print Settings ..................... 84 Star Cloud Services ....................... 88 4.4.1 Device Registration ......................89 4.4.2 Setting of Registration ....................90 4.5.
Page 4 4.13. Barcodes ..........................140 4.13.1. ITF Bearer Bars......................141 4.13.2. UPC-A Guard Bar Length ................... 141 4.13.3. JAN/EAN-13 Guard Bar Length ................. 142 4.13.4. CODE39 Guard Bar Length <Star Line Mode Only> ..........142 4.13.5. CODE39 Character Set <Star Line Mode Only> ............143 4.14.
Page 5: Getting Started
Getting Started This software supports the following Windows operating systems. ・Windows 10 * 32-bit and 64-bit (except Windows 10 Mobile and Windows 10 IoT Core) ・Windows 8.1 * 32-bit and 64-bit (except WindowsRT 8.1) ・Windows 8 * 32-bit and 64-bit (except WindowsRT) ・Windows 7 32-bit and 64-bit * Limitation for Windows 10 / 8.1 / 8 ・...
Page 6: Installation And Uninstallation
Software Manual 1. Installation and Uninstallation To use the TSP100 futurePRNT product in a Windows environment, you need to install this printer driver in advance. Notes: 1) If the TSP100GT (version 1.0a or earlier) or TSP100LAN (version 1.1a or earlier) driver utility application is installed, uninstall it before starting operations.
Page 7 Software Manual << Models supplied with CDs >> Insert the CD-ROM supplied with the TSP100 futurePRNT into the CD-ROM drive of your computer. When the following window appears, click “Run Autorun.exe”.  In Windows 8/8.1/10: Toast pop up will be appeared after CD-ROM is set. After that, click [Run Autorun.exe].
Page 8 Software Manual Then, the following window will appear. Click “Installation” on the menu. Read this software license agreement carefully. If you agree to the terms of this license, click "I Accept". The "User Account Control" window will appear. Click "Yes".
Page 9 Software Manual Click “Next” to continue. Choose the user and then click “Next” to continue.
Page 10 Software Manual Choose the “Typical” installation option to be sure that all of the TSP100 futurePRNT’s options are installed and then click “Next” to continue. Click “Install” to begin the installation process.
Page 11 Software Manual (10) The files and programs are now being installed on the computer. (11) At this point, all drivers and programs have been installed. Click “Finish” to close the wizard. If the "Launch Star Cloud Services Web site" check box is checked (default), Star Cloud Services website will open after the installation wizard is finished.
Page 12 (12) Click "Exit" to close the following window. (13) The subsequent steps vary depending on the model you are using. 1.2 Adding a Printer (TSP100U/PU/GT/ECO) 1.3 Adding a Printer (TSP100LAN) 1.4 Adding a Printer (TSP100IIIW) 1.5 Adding a Printer (TSP100IIILAN)
Page 13: Adding A Printer (Tsp100U/Pu/Gt/Eco)
Software Manual 1.2. Adding a Printer (TSP100U/PU/GT/ECO) Load roll paper in the TSP100 futurePRNT, and connect to a computer. For information about how to load paper and connect to a computer, refer to the TSP100 futurePRNT hardware manual. To view the hardware manual, select "Documents/SDK" on the “CD auto” menu, and click "Hardware Manual".
Page 14: Adding A Printer (Tsp100Lan)
Software Manual 1.3. Adding a Printer (TSP100LAN) Prior to installation, use an Ethernet cable to connect the printer and an access point that can connect to the same network the PC that will be used for configuration is on. For details, see the Hardware manual.
Page 15 Software Manual (5) The TSP100LAN Ethernet Setup Tool screen is displayed. If the printer you want to install is not listed in the LAN printer list, click [Discovery]. The factory network settings of the TSP100LAN printer are as follows. IP address: 0.0.0.0 (Unassigned) Subnet mask: 0.0.0.0 (Unassigned)
Page 16 Software Manual (6) The TSP100LAN printer appears in the LAN printer list. If multiple TSP100LAN printers are listed, you can identify the desired printer by referring to the indicated MAC address. If you wish to use the IP address assigned by the DHCP server, click the [Add printer queue] button.
Page 17 Software Manual ■ When the IP address cannot be obtained from the DHCP server : When the DHCP server is not available, "Did not obtain" is displayed in the ‘IP address’ field for a printer that is not assigned to any IP address. To use such a printer, follow the steps below to specify the IP address.
Page 18 Software Manual (7) Uncheck "Dynamic (DHCP)", enter the IP address, subnet mask, and default gateway, and then click [Apply]. Ask your network administrator about the static IP address and subnet mask to use in the settings. ・If you enable “Multi Session”, it will be possible for terminals to get status from the printer even when multiple terminals are connected simultaneously.
Page 19 Software Manual (8) Click [Yes] on the screen asking to confirm application. The configuration is saved to the printer and printed out. (9) A message is displayed indicating that the configuration was applied. Click [OK], and then proceed to Section 1.3.2, "Creating a Printer Queue." Note: After the printer reset, it may take a short time (perhaps 20 seconds) for the printer to be found again.
Page 20: Creating A Printer Queue
Software Manual 1.3.2. Creating a Printer Queue Select the printer to create a printer queue from the LAN printer list, and then click [Printer Queue]. The following dialog now appears. The dialog shows the queue name and port name for the printer you are setting up.
Page 21 Software Manual (3) Click [Yes] on the screen asking to confirm application. The printer queue is created. A message is displayed indicating that setup is complete. Click [OK]. In Control Panel, select “Devices and Printers”. If the Star TSP100LAN printer is found in the window, installation is completed.
Page 22: Adding A Printer (Tsp100Iiiw)
Software Manual 1.4. Adding a Printer (TSP100IIIW) This manual describes how to connect the printer using WPS. If you are using Windows 7, you can also connect over an Ad-Hoc network. For details, see the Online manual (Setup - Connect Tablet/PC).
Page 23 Software Manual If the "Windows Security Alert" screen is displayed, click [Allow access]. Notes: If you click [Cancel], you will not be able to search for the LAN printer. (6) The TSP100LAN Ethernet Setup Tool screen is displayed. If the printer you want to install is not listed in the LAN printer list, click [Discovery]. The factory network settings of the TSP100IIIW printer are as follows.
Page 24 Software Manual (7) The TSP100 Ethernet printer appears in the LAN printer list. If multiple TSP100IIIW printers are listed, click [Check connection] to check whether you can communicate with the printer. The connected printer's LED (blue) will blink. If you wish to use the IP address assigned by the DHCP server, then proceed to Section 1.4.2, "Creating a Printer Queue", below.
Page 25 Software Manual ■ When the IP address cannot be obtained from the DHCP server : When the DHCP server is not available, "Did not obtain" is displayed in the ‘IP address’ field for a printer that is not assigned to any IP address. To use such a printer, follow the steps below to specify the IP address.
Page 26 Software Manual (8) Open [Login] from the menu displayed on the left side of the setting screen, or the menu button displayed on the upper left, and login with: Login name: root / password: [Changed password or the default password (public)]. The default login name and password are as follows: Login name: root Password: public...
Page 27 Software Manual (10) From the menu displayed on the left side of the setting screen or the menu button displayed on the upper left, open [IP Parameters] , select “Static” and enter the IP Address, Subnet Mask, and tap [Submit]. Ask your network administrator about the static IP address and subnet mask to use in the settings.
Page 28: Creating A Printer Queue
Software Manual 1.4.2. Creating a Printer Queue Select the printer to create a printer queue from the LAN printer list, and then click [Printer Queue]. The following dialog now appears. The dialog shows the queue name and port name for the printer you are setting up.
Page 29 Software Manual (3) Click [Yes] on the screen asking to confirm application. The printer queue is created. A message is displayed indicating that setup is complete. Click [OK]. (4) In Control Panel, select “Devices and Printers”. If the Star TSP100IIIW printer is found in the window, installation is completed.
Page 30: Adding A Printer (Tsp100Iiilan)
Software Manual 1.5. Adding a Printer (TSP100IIILAN) Prior to installation, use an Ethernet cable to connect the printer and an access point that can connect to the same network the PC that will be used for configuration is on. For details, see the Online hardware manual (Setup –...
Page 31 (5) The TSP100LAN Ethernet Setup Tool screen is displayed. If the printer you want to install is not listed in the LAN printer list, click [Discovery]. The factory network settings of the TSP100IIILAN printer are as follows. IP address: 0.0.0.0 (Unassigned) Subnet mask: 0.0.0.0 (Unassigned)
Page 32 Software Manual (6) The TSP100 Ethernet printer appears in the LAN printer list. If multiple TSP100IIILAN printers are listed, click [Check connection] to check whether you can communicate with the printer. The connected printer's LED (blue) will blink. If you wish to use the IP address assigned by the DHCP server, then proceed to Section 1.5.2,...
Page 33 Software Manual ■ When the IP address cannot be obtained from the DHCP server : When the DHCP server is not available, "Did not obtain" is displayed in the ‘IP address’ field for a printer that is not assigned to any IP address. To use such a printer, follow the steps below to specify the IP address.
Page 34 Software Manual (7) Open [Login] from the menu displayed on the left side of the setting screen, or the menu button displayed on the upper left, and login with: Login name: root / password: [Changed password or the default password (public)]. The default login name and password are as follows: Login name: root Password: public...
Page 35 Software Manual (9) From the menu displayed on the left side of the setting screen or the menu button displayed on the upper left, open [IP Parameters] , select “Static” and enter the IP Address, Subnet Mask, and tap [Submit]. Ask your network administrator about the static IP address and subnet mask to use in the settings.
Page 36: Creating A Printer Queue
Software Manual 1.5.2. Creating a Printer Queue Select the printer to create a printer queue from the LAN printer list, and then click [Printer Queue]. The following dialog now appears. The dialog shows the queue name and port name for the printer you are setting up.
Page 37 (3) Click [Yes] on the screen asking to confirm application. The printer queue is created. A message is displayed indicating that setup is complete. Click [OK]. In Control Panel, select “Devices and Printers”. If the Star TSP100IIILAN printer is found in the window, installation is completed.
Page 38: Uninstallation
Software Manual 1.6. Uninstallation Turn the printer off. From the Windows Start menu, select “All Programs or All Apps” → “StarMicronics” → “Star TSP100” → “Uninstall”. In the User Account Control dialog box, click the “Yes”. When the following confirmation dialog box appears, click “Yes” to continue. If the following window appears, select “Do not close applications”...
Page 39 Software Manual (7) The uninstaller launches to remove all of the TSP100 futurePRNT software form your computer.
Page 40: Features
Software Manual 2. Features 2.1. Star Windows Printer Driver The Star Windows Printer Driver is used to apply the futurePRNT series in Windows 10, 8.1, 8 or Windows 7. Using this printer driver allows you to handle basic printing functions in many Windows applications.
Page 41: Javapos Driver
2.4. Star Virtual Serial Port Emulator This function allows you to use the TSP100U/PU/GT/ECO with the USB interface equipped or the TSP100LAN, TSP100IIIW and TSP100IIILAN with the Ethernet interface equipped using applications for a serial printer. Notes: This function may not be available depending on applications.
Page 42: Esc/Pos Mode
Printer)". 2.6. Star Virtual TCP/IP Port Emulator <TSP100LAN, TSP100IIIW and TSP100IIILAN only> You can use the TSP100LAN Setup Utilities to set up virtual TCP/IP ports. This will enable you to continue using applications that directly designate their own TCP/IP sockets.
Page 43: Windows Printer Driver Usage
Software Manual 3. Windows Printer Driver Usage 3.1. Device Settings Various functions of this driver can be configured in “Properties” menu of the printer. In case of using Windows 8.1 and 8, change the setting from “Desktop UI” in order to change settings.
Page 44 Software Manual Paper Type You can choose the length of each printed page. Value Default Details Receipt Pages have variable length (printed to last line). Ticket All printed pages have same length. Page Cut Type (Cutter Model only) You can choose the cut type that is performed at the end of all intermediate pages (all pages up to the last page).
Page 45 Software Manual Peripheral Unit Type Use this setting to select the type of peripheral to be used with the printer. Value Default Details Buzzer Use buzzers as peripheral device. Cash Drawer Use buzzers as peripheral device. Caution: When using a peripheral unit such as a cash drawer other than a buzzer, do not select "Buzzer".
Page 46 Software Manual Cash Drawer 1 Pulse Width You can choose the length of the open drawer signal that is sent from the printer to Cash Drawer 1. Value Default Details 10 milliseconds Pulse width is set as 0.01 sec. 100 milliseconds Pulse width is set as 0.1 sec.
Page 47 Software Manual Buzzer1 - Off Time If the Peripheral Unit Type is set to Buzzer, this setting selects the beep OFF time for the buzzer operating as peripheral unit 1. Value Default Details 20 milliseconds Silent on for 0.02 sec. 40 milliseconds Silent on for 0.04 sec.
Page 48 Software Manual Buzzer2 - On Time If the Peripheral Unit Type is set to Buzzer, this setting selects the beep ON time for the buzzer operating as peripheral unit 2. Value Default Details 20 milliseconds Sound on for 0.02 sec. 40 milliseconds Sound on for 0.04 sec.
Page 49 Software Manual Buzzer2 - Repeat If the Peripheral Unit Type is set to Buzzer, this setting selects the number of beeps produced by buzzer #2 when it is activated. (Each beep will sound for the specified ON time, followed by silence for the specified OFF time).
Page 50: Paper Size Settings
Software Manual 3.2. Paper Size Settings This driver allows you to use both the predefined and user-defined paper sizes. Each paper size is defined by "width" and "length", enabling printing of all the area in the defined range. Margin setting is not required in a document. To print on a variable-length sheet such as a receipt, select the paper size that includes "Receipt"...
Page 51: Standard Paper Sizes
Software Manual 3.2.1. Standard Paper Sizes This driver set defines two standard paper sizes (Built-in paper size) - A4, Letter, four custom paper sizes, and also supports user defined paper sizes. The following table is the list of the custom paper sizes supported by this printer driver. Built-in paper sizes Width Length...
Page 52: User-Defined Paper Size
Software Manual 3.2.2. User-Defined Paper Size Follow the steps below to specify a user-defined paper size using a Windows standard function. In Control Panel, select “Devices and Printers”. Select a target printer, and click "Print Server Properties". Click the "Forms" tab. Check the "Create a new form"...
Page 53: Device Font Usage
Software Manual 3.3. Device Font Usage This driver supports various device fonts. Printer fonts provide some font sizes, enabling clearer printing than for the TrueType font. Using barcode and 2D code fonts allow you to generate and print barcodes and 2D codes of various standards and sizes you entered.
Page 54 Software Manual Number of Width Height Device Font Name Details digits, 72 mm (Pixels) (Pixels) (576 dots) Printer font Printer Front B 8.5cpi (ANK font B) Printer Front B 8.5cpi Tall Printer Front B 10cpi Printer Front B 10cpi Tall Printer Front B 11cpi Printer Front B 11cpi Tall Printer Front B 17cpi...
Page 55 Software Manual Digit number Width Height Device Font Name Details 72 mm (Pixels) (Pixels) (576 dots) Control Device control font ESC_FONT UPC-E UPC-A JAN/EAN-8 JAN/EAN-13 Barcode device font CODE39 NW-7 (Codaber) QR_CNTL PDF417 DATA1 2D code font DATA2 DATA3...
Page 56: Control Font Usage
Software Manual 3.4. Control Font Usage The Control device font is used to provide for control within the span of a single document. This font is not used for character printing. 3.4.1. Control Font list The following table is the list of the supported control device fonts. Character Function Open cash drawer 1 for 50 mSec.
Page 57 Software Manual Character Function Select Denmark II international character set Select Spain II international character set Select Latin America international character set Select turn over printing Cancel turn over printing Select the customer display Deselect the customer display Clear the customer display Notes: The settings above will be ignored if a specified control character is not supported by the printer.
Page 58: Control Font Usage
Software Manual 3.4.2. Control Font Usage Usage of the Control font must be done as follows: - Select Control Font 1. Choose the control font from your editor’s font menu. - Input Control Font 2. Enter the characters for the printer actions which you want to use.
Page 59: Barcode Font
Software Manual 3.5. Barcode Font After printing Barcode, small characters are printed under barcode. But the barcode image data is not displayed. This action is only available when Print mode option is set to Line mode. On Raster Mode, this setting is not available. 3.5.1.
Page 60 Software Manual Barcode Device Font Parameter Function Character UPC-E, UPC-A, for Barcode Details CODE39 JAN/EAN-8, printing NW-7 JAN/EAN-13 2 dot 2 dot (6) 2 dot (5) Minimum module width 3 dot 3 dot (9) 4 dot (10) Minimum module width 4 dot 4 dot (12) 6 dot (15)
Page 61: Barcode Font Usage
Software Manual 3.5.3. Barcode Font Usage Usage of the Barcode device font must be done as follows: - Select Barcode Font 1. Choose the barcode device font from your editor’s menu...
Page 62 Software Manual - Input Barcode font 2. Input code. The specified function is performed by printing. <Print result sample> Please set the barcode device font's character size to the standard value (8.5 points).
Page 63: Code Printing Function (2D Code Fonts)
Software Manual 3.6. 2D Code Printing Function (2D Code Fonts) The 2D code printing function performs QR code or PDF417 printing using device fonts supported in this driver. QR code or PDF417 printing is realized with a combination of 2D code fonts (”QR_CNTL”, ”PDF417”, ”DATA1”, ”DATA2”, and ”DATA3”) and control fonts (”ESC_FONT”...
Page 64: Code Command Setting Font
Software Manual Description data: E2A0* 012345ABCDP Description character Setting font Meaning (1) ‘E2’ QR_CNTL Sets to correct errors level Q (25%). (2) ‘AO’ QR_CNTL QR Code data setting (Automatic data analysis) (2) ‘*’ DATA1 QR Code data setting parameter A = ￥x0A = ‘*’ *１ (2) ‘...
Page 65 Software Manual QR_CNTL Fonts Function Output Code Set model of QR code: Model 1 \x1b\x1dyS0\x01 Set model of QR code: Model 2 \x1b\x1dyS0\x02 Set up correct errors level \x1b\x1dyS1 Correct errors level L * El (E0) \x1b\x1dyS1\x00 (correction rate: 7%) Correct errors level M * Em (E1) \x1b\x1dyS1\x01...
Page 66 Software Manual Character Function Driver-output code command Used for parameter of each PDF417 setting \x07 command Used for parameter of each PDF417 setting \x08 command Used for parameter of each PDF417 setting \x09 command Specifies the PDF417 code size. \x1b\x1dxS0 Specifies the PDF417 security level (ECC).
Page 67: Code Data Setting Font (Data1, Data2, Data3, Esc_Font)
Software Manual 3.6.3. 2D Code Data Setting Font (DATA1, DATA2, DATA3, ESC_FONT) Input Data Output Data On applications (Word, VB, etc), Output code for printer user specified characters Character Code ESC_FONT DATA1 DATA2 DATA3 <SP> \x20 \x20 \x00 \x60 \xC0 \x21 \x21 \x01...
Page 68 Software Manual Input Data Output Data On applications (Word, VB, etc), Output code for printer user specified characters Character Code ESC_FONT DATA1 DATA2 DATA3 \x47 \x47 \x27 \x87 \xE7 \x48 \x48 \x28 \x88 \xE8 \x49 \x49 \x29 \x89 \xE9 \x4A \x4A \x2A \x8A...
Page 69 Software Manual Input Data Output Data On applications (Word, VB, etc), Output code for printer user specified characters Character Code ESC_FONT DATA1 DATA2 DATA3 \x72 \x72 \x52 \xB2 \x73 \x73 \x53 \xB3 \x74 \x74 \x54 \xB4 \x75 \x75 \x55 \xB5 \x76 \x76 \x56...
Page 70: Code Font Usage
Software Manual 3.6.4. 2D Code Font Usage QR code can be specified up to 500 bytes. (It includes input data and punctuated marks in 500bytes.) Sample programs of Visual Basic using 2D code is as follows; QR Code Print Sample1: Private Sub Command1_Click() Printer.Font.Name = "Printer 17cpi Tall Printer.Print "QR Code Test Print for VB 6.0"...
Page 71 Software Manual QR Code Print Sample2: Private Sub Command2_Click() Printer.Font.Name = "Printer 17cpi Tall" Printer.Print "QR Code Test Print for VB 6.0" Printer.Font.Name = "Printer 17cpi" Printer.Print Printer.Print "DATA:" Printer.Print "http://www.star-m.jp/" Printer.Print Printer.Print "QR code:"; Printer.Font.Name = "QR_CNTL" ' QR_CNTL font setting Printer.Print "M1";...
Page 72 Software Manual ■ PDF417 printing - Sample 1 Private Sub Command4_Click() Printer.Font.Name = "Printer 17cpi Tall" Printer.Print "PDF417 Test Print for VB 6.0" Printer.Font.Name = "Printer 17cpi" Printer.Print Printer.Print "DATA:" Printer.Print "1234567890" Printer.Print Printer.Print "PDF417: "; Printer.Font.Name = "PDF417" Printer.Print "S023"; ' Specifies the barcode size.
Page 73 Software Manual ■ PDF417 printing - Sample 2 Private Sub Command5_Click() Printer.Font.Name = "Printer 17cpi Tall" Printer.Print "PDF417 Test Print for VB 6.0" Printer.Font.Name = "Printer 17cpi" Printer.Print Printer.Print "DATA:" Printer.Print " http://.star-m.jp/" Printer.Print Printer.Print "PDF417:"; Printer.Font.Name = "PDF417" Printer.Print "S023"; ' Specifies the barcode size.
Page 74: 2-Tone Color Printing And Paper Type Settings
Software Manual 3.7. 2-Tone Color Printing and Paper Type Settings This driver supports two-tone color printing. To perform two-tone color printing and use special paper, load the appropriate thermal paper in the printer, and configure the following setting. In Control Panel, select “Devices and Printers”. Right-click on the icon of the target printer queue, and select “Printing preferences”...
Page 75 Software Manual When the “Printing Preferences ... ” window opens, click the “Paper/Quality” tab. Then, select the type of paper that suits the print color that has been specified. Paper Type and Print Color Configuration Window Select paper type Specify print color For normal gray scale printing For gray scale printing on normal thermal paper, select the following:...
Page 76: Tsp100 Configuration Application
Software Manual 4. TSP100 Configuration Application The TSP100 configuration application lets you control the look and content of printed receipts. You can set up separate configurations for Star Line mode and for ESC/POS mode. Notes: TSP100 configuration application settings require computer administrator privileges. There are the following two methods to launch the TSP100 configuration application.
Page 77 When using the TSP100LAN, click “OK” to start the Ethernet setup tool, and add the required printer, referring to "1.3 Adding a Printer (TSP100LAN)", “1.4 Adding a Printer(TSP100IIIW)” or “1.5 Adding a Printer(TSP100IIILAN)”. When using a non-TSP100LAN printer, click “Cancel” to stop the procedure, and add the...
Page 78 Software Manual If the application is launched from the Start menu while there are multiple available printer queues, the following window will appear. Select a target printer, and click “OK”. If the LAN function is installed, you can select the "Add TSP100LAN" checkbox to start the Ethernet setup tool.
Page 79: Menu Functions
Software Manual 4.1. Menu Functions The menu bar in the “TSP100 Configuration” contains the “File”, “View”, “ECO”, “Management” and “Help” menus. Each menu is explained on the following pages. 4.1.1. File 1. Export The settings made using the “TSP Configuration” can be saved. The settings are saved as a file with an “.xml”...
Page 80 Software Manual When importing data using an operating system or user different from that for exporting data, execute the following steps to use the HexDump mode, ECO settings - on-demand function, and journal function.  HexDump Mode 1. Change the folder where to save data in the HexDump mode setting window. 2.
Page 81: View
Software Manual 3. HexDump Mode All of the data transmitted to the printer from the computer is printed or output as a file using hexadecimal code. The data transmitted to the printer can be checked for correctness and the causes of errors can be investigated.
Page 82 Software Manual 1. List display/Icon display The setting items for the “TSP Configuration” can be displayed as a list or as icons. 2. Language selection The display language can be selected. STEP 1: On the “View” menu, select “Language selection” to display the list of available languages.
Page 83: Eco
Software Manual STEP 2: Select the language, and then click “Select”. STEP 3: Click “Select”, and then temporarily close the “TSP Configuration”. By opening the “TSP Configuration” again, the selected language will be displayed. Note: If the characters are corrupted, change the settings in the Advanced tab in Regional Options in Control Panel in Windows.
Page 84 Software Manual ECO indicator setting Select "Enabled" checkbox in the "ECO Indicator" window to start measurement. Check the result. After printing, open the "ECO Indicator" window again to check the result. Clear the accumulated result. Click “Clear” to clear the accumulated result.
Page 85: Management
Software Manual 4.1.4. Management This is used to record logs and identify causes when communication errors occur. 4.1.5. Help The software version can be confirmed using the “Help” menu.
Page 86: Information
Software Manual 4.2. Information The Information window displays device information of the printer to be configured.
Page 87: General Settings
Software Manual 4.3. General Settings Click the "General Settings" tab in the left pane of the window. When the printer driver is used for printing, text and line spacing settings are available only when device fonts are used.
Page 88: Default Text Settings
Software Manual 4.3.1. Default Text Settings ■ Zero Style The default zero style is "Standard". Selects whether the printer prints zeros in non-slashed form or slashed form. Select either “Standard” (O) or “Slashed” (Ø). ■ International Character Set The default international character set is "USA". Changing the international character set will change certain characters in the character table to match those characters fitting the selected location.
Page 89: Default Print Settings
Software Manual ■ Character Encoding The default character encoding is "Single Byte Characters". Selects the character encoding used by the printer. You can select either single-byte encoding (common for all non-Asian languages) or any of the four available double-byte encodings (for the corresponding Asian languages).
Page 90 Software Manual mm-tall line of characters. If the spacing is set to 3 mm, the added spacing is omitted and receipts are correspondingly shorter. But note that the shorter receipts may be harder to read. ■ Print Density Adjusting the print density allows for adjustment in the level of contrast to compensate for the different levels of sensitivity of different types and grades of thermal paper.
Page 91 Software Manual ■ Print Width The print width should be set according to the size of paper used. The default (recommended print width) is 72 mm.The standard default print width is 72 mm, which provides 4-mm margins on both sides of 80-mm paper. The 51-mm print width setting is appropriate if you are using the optional 58-mm paper supported by the TSP100 futurePRNT.
Page 92 Software Manual ■ Resolution Pitch <ESC/POS mode only> Star Line standard: Uses Star Line mode’s standard resolution. (Characters are smaller than on true ESC/POS printers, so the printer receipt is smaller and the right margin is larger.) ESC/POS compatible (default): Margins and line widths are the same as on a typical ESC/POS printer.
Page 93: Star Cloud Services
Software Manual 4.4. Star Cloud Services Click the Star Cloud Services tab on the left side of the dialog box. To use the Star Cloud Services, it is required to register a Star Cloud Services account in advance. Please click “Here” for details.
Page 94: Device Registration
Software Manual 4.4.1. Device Registration Register the device (futurePRNT series printer queue) using your registered Star Cloud Services account. Once you have registered the device, you can use the service of uploading print data to the cloud server and manage the registered device from the Star Cloud Services dashboard. (1) Enter the username and the password of your registered Star Cloud Services account and click “Register Device”.
Page 95: Setting Of Registration
Software Manual 4.4.2. Setting of Registration When “Print Data Upload” is checked, the QR code is added on the receipt and the data of printed receipt is uploaded on the Star Cloud Server. The print size of QR code can be specified. Print Sample) Note: To upload data on the Star Cloud Server, the host device must be connected to the network.
Page 96: Eco Settings
Software Manual 4.5. ECO Settings Click the ECO Settings tab on the left side of the dialog box. 4.5.1. Auto Reduction Setting This function reduces the overall size of the printing. However, to prevent any scanning errors, the size of printed barcodes is not reduced even if the reduction settings are selected.
Page 97: Top Margin To First Line
Software Manual ■ Paper width used The default setting is “80mm (Do Not Compress)”. By changing the setting to 80mm->58mm, the printing area is compressed widthwise so that 58 mm width roll paper can be used instead of 80 mm width roll paper. 1) If the printing width is set to 51 mm using General Settings in the configuration utility, the 80mm->58mm setting in Paper width used is disabled.

Page 98: On Demand
Software Manual The default setting is 3mm. We recommend 3 mm as being effective for the ECO function; however, backward feeding is carried out for each cut operation when 10 mm or fewer is specified. To reduce the printing time, set to 11 mm. 4.5.3.
Page 99 Software Manual Normally, the confirmation dialog box appears before the data is printed. However, in rare cases, the confirmation dialog box may not appear, the dialog box may appear after the data is printed, or other problems with the operation of the function may occur. If any of these problems occur, restart your computer.
Page 100 Software Manual ■ View Save Data The data for canceled printings can be viewed. In addition, to print data that was saved from a canceled printing, perform the following procedure. Click View Save Data. The Journal tool window appears. Click “Search” to search for the saved data. Enter the date to start searching, and click “OK”.
Page 101 Software Manual Enter the date to end searching, and click “OK”. This will search for the data saved in the specified period. Click the date to check data details in the preview screen. The saved data appears. Click Print to print the data.
Page 102 Software Manual Caution When using the on demand function, check the following information. When the on demand function is enabled, the time that the confirmation dialog box appears may vary according to the printing channel that is used. The time that the confirmation dialog box appears for each channel is as follows: Printer Driver Immediately after a cut command is sent...
Page 103: Printer Tests
Software Manual 4.6. Printer Tests The page lets you generate various sample receipt printouts. Use this feature to test or demonstrate the TSP100 futurePRNT’s printing capabilities. 4.6.1. Default Character Set Prints a table exhibiting the entire TSP100 futurePRNT default single byte character table. ■...
Page 104: Cashdrawer/Peripheral Device Test
In the ESC/POS mode, you can click the cash drawer test button to check that the buzzer connected to the printer sounds. 4.6.3. TSP100III Connection check <<TSP100IIIW, TSP100IIILAN only>> ■ Connection check Click [Check the connection] to check whether you can communicate with the printer. The connected...
Page 105: Opos Installation
Software Manual 4.7. OPOS Installation <Star Line mode only> The OPOS printer driver is included with the Windows driver installation. However, before it can be used with an OPOS application, the printer must be registered. If a cash drawer is connected to the printer, the cash drawer must also be registered.

Page 106: Adding A Printer
Software Manual 4.7.1. Adding a Printer ● When no control object is registered: “Not Selected” is selected in the ‘Control Object Registration’ field. Click “Add New”. The following dialog box appears. Enter the name of the printer to be added, select the print width and click “OK”.
Page 107 Software Manual ● When "OPOS CCO" or "Star CO" is registered as a control object: "OPOS CCO" or "Star CO" is selected in the ‘Control Object Registration’ field. Click “Add New”. <When "Star CO" is selected> The following dialog box appears. Enter the name of the printer to be added, select the print width and click “OK”.
Page 108 Software Manual ● When a non-Star control object is registered: "Others" is grayed out in the ‘Control Object Registration’ field. Click “Add New”. The following confirmation dialog box appears. To register the recommended common control object (OPOS CCO), click “Yes”, and proceed to step (3).
Page 109 Software Manual The following dialog box appears. Enter the name of the printer to be added, select the print width and click “OK”. ■ 180dpi compatible mode When 180dpi compatible mode is checked, the left and right margins are automatically adjusted.
Page 110: Configuring A Printer
Software Manual 4.7.2. Configuring a Printer Click “Configure” for OPOS POSPrinter to specify a logical device name for a target printer. Select a target printer, and click “Configure”. The following window appears. Click “Add New”. The setting value is displayed only when the print width of the printer is set to 51 mm. Enter the name, and click “OK”.
Page 111: Adding A Cash Drawer
Software Manual To check the printing status in the specified range, select the "Do Checked Block Printing" checkbox. Click “Accept”. 4.7.3. Adding a Cash Drawer ● When no control object is registered: “Not Selected” is selected in the ‘Control Object Registration’ field. Click “Add New”.
Page 112 Software Manual The cash drawer is added, and "OPOS CCO (OPOS common control object)" is selected in the ‘Control Object Registration’ field. Click “Apply Changes” to register the new cash drawer. ● When "OPOS CCO" or "Star CO" is registered as a control object: "OPOS CCO"...
Page 113 Software Manual The cash drawer is added. Click “Apply Changes” to register the new cash drawer. ● When a non-Star control object is registered: "Others" is grayed out in the ‘Control Object Registration’ field. Click “Add New”. The following confirmation dialog box appears. To register the common control object (OPOS CCO), click “Yes”, and proceed to step (3).
Page 114 Software Manual The following confirmation dialog box appears to check with you if you want to delete the currently registered control object. To continue, click “Yes”. Notes: Once a control object is deleted, it cannot be recovered. The following dialog box appears. Enter the name of the cash drawer to be added. Click “OK”.
Page 115: Configuring A Cash Drawer
Software Manual 4.7.4. Configuring a Cash Drawer Click “Configure” in the OPOS CashDrawer window to specify a logical device name for a target cash drawer. When necessary, you can configure cash drawer operations. Select a target cash drawer, and click “Configure”. The following window appears.
Page 116: Delete
Software Manual Configure cash drawer operations. ■ Status Selecting the "Status" checkbox notifies the open-close state of the cash drawer. If the "Status" checkbox is not selected, it will not be possible to notify the open-close state of the cash drawer. Notes: This function is available only when the selected cash drawer supports the open-close detector switch.
Page 117: Check Health
Software Manual 4.7.6. Check Health The “Check Health” button performs a system check to ensure that the printer is connected and working properly under OPOS. After the initial check, a sample receipt will be printed to show the printer is printing with its full capability. 4.7.7.
Page 118: Javapos™ Installation
Software Manual To begin the sample application, first select the device from the drop-down menu. Next follow the steps below: 1. Click “Open” to open the OPOS device. 2. Click “Claim” to claim the device for the sample application’s use. Start 3.

Page 119 Software Manual connected to the printer, the cash drawer must also be registered. Registration of the printer and cash drawer is accomplished through the configuration utility.
Page 120 Software Manual The "JavaPOS XML file" is required to register and configure printer and cash drawer. First, click “Create JavaPOS XML Registry File” to create a JavaPOS XML file. If the JavaPOS XML file resides, click “Load JavaPOS XML Registry File” to load the JavaPOS XML file. Then, to register printer and cash drawer, execute the steps shown in the following page.
Page 121: Add A New Printer Device
Software Manual 4.8.1. Add a New Printer Device Click “Add New” next to the POSPrinter textbox Enter a logical name for your JavaPOS™ printer device in the resulting dialog. 4.8.2. Configure a Printer Device Click “Configure” next to the POSPrinter textbox with the desired device highlighted.
Page 122: Add A New Cash Drawer Device
Software Manual 4.8.3. Add a New Cash Drawer Device Click “Add New” next to the Cash Drawer textbox. Enter a logical name for your JavaPOS™ cash drawer in the resulting dialog. 4.8.4. Configure a Cash Drawer Device Click “Configure” on the right of the text box in the JavaPOS CashDrawer window to configure cash drawer operations.
Page 123 Software Manual ■ Status Select the “Status” checkbox to enable monitoring of the compulsion switch if the cash drawer supports Notes: This function is available only when the selected cash drawer supports the open-close detector switch. ■ Active Select the “Active” checkbox to choose whether the “open” setting of the compulsion switch is recognized as an open or closed cash drawer.
Page 124: Deleting A Printer Or Cash Drawer
Software Manual ■ Activation Pulse Width Select how long the signal to open the cash drawer will be sent. ■ Post Activation Pause Select how long the pause between cash drawer open signals will be. For cash drawer 2, the power distribution and delay times are fixed to 200 msec. 4.8.5.
Page 125: Check Health
Software Manual 4.8.6. Check Health Click “Check Health” next to each text box to perform a system check about whether the printer or cash drawer is connected normally or it is working properly under JavaPOS. After the initial printer check, the results of all printer functions are printed on a sample receipt. If the initial check succeeds, the following window appears.
Page 126 Software Manual Refer to the following information for setting the environment variables when using JavaPOS. 1. At the Windows Start menu, right-click Computer, and then select Properties. 2. The System dialog box appears. Click Change settings. 3. At the System Properties dialog box, click the Advanced tab, and then click Environment Variables. 4.
Page 127: Seral Port (Star Serial Port Emulator)
This function generates a virtual serial port (COM port). Using this function allows you to use the TSP100U/TSP100PU/TSP100GT/TSP100ECO with the USB interface equipped or the TSP100LAN/TSP100IIIW/TSP100IIILAN with the Ethernet interface equipped using applications for a serial printer. Print data must be sent to a virtual serial port on a one-document basis. If print data is divided into many parts for sending, the print speed will slow down compared to when sending on a one-document basis.
Page 128: Creating A Virtual Serial Port
Software Manual 4.9.1. Creating a Virtual Serial Port The procedure for creating a virtual serial port varies depending on the model you are using and the firmware version of the printer. ● For TSP100ECO (firmware version 2.0 or later) and TSP100GT (firmware version 2.0 or later) Click “Add Port”.
Page 129 Software Manual ● For TSP100U/PU, TSP100LAN, TSP100ECO (firmware versions earlier than firmware version 2.0), TSP100GT (firmware versions earlier than firmware version 2.0), TSP100IIIW and TSP100LAN. Click “Add Port”. The following window appears. Enter the port name, and click “OK”. For Input Port Name, enter the name of the output destination port of the currently used POS application.
Page 130: Configuring The Port Emulator Service
Software Manual 4.9.2. Configuring the Port Emulator Service By default, the port emulator service is disabled. To use the port emulator, the service must be set to either manual or automatic operation. Automatic is the most common usage as it will start each time the system is booted.
Page 131: Image List
Software Manual 4.10. Image List The image list allows for the queuing of bitmap images (jpg, gif, bmp format) for later automatic printing. An infinite number of images can be queued at any given time for fast and easy recall during printing. 4.10.1.
Page 132 Software Manual Click “Add New” to browse for an image to add to the list. The following "Image Import" window appears.
Page 133: Renaming An Image
Software Manual Use the image importer to: • Give your image a unique name using the Image ID Name field • Adjust image width in 1/8 mm increments using the image width slider • Select the preferred dithering method • Adjust dither settings to desired image quality Note: Each dither method offers different adjustment options.
Page 134: Logos & Cropping
Software Manual 4.11. Logos & Cropping Logos & Cropping allows for the selection of images to be printed at the top of each receipt (logos) and images to be printed at the bottom of each receipt (coupons). The ability to crop a receipt for white space or logo/coupon removal can also be configured here.
Page 135: Logo Printing
Software Manual 4.11.1. Logo Printing The following shows the setting required to print an image on a receipt.
Page 136 Software Manual ■ Top image setting Print the selected image at the top of a receipt. Click “Add” next to the “Top Image List” text box. Select the desired image from the image list registered in "4.8.1 Adding an Image", and specify the image printing position in Alignment.
Page 137 Software Manual  Bottom image setting Print the selected image at the bottom of a receipt. Click “Add” next to the “Bottom Image List” text box. Select the desired image from the image list registered in "4.8.1 Adding an Image", and specify the image printing position in Alignment.
Page 138 Software Manual  Merge image setting Print the selected image in the background of a receipt. Click “Select” in the ‘Merge Image’ field. Select the desired image from the image list registered in "4.8.1. Adding an Image". Click “Use”. Select the "Include logos and coupons when merging" checkbox to apply the selected merge image to the entire printing area.
Page 139: Logo Cropping
Software Manual 4.11.2. Logo Cropping Specify the top and bottom crop lengths of a receipt. Using this function performs printing while leaving the blank spaces specified with the top and bottom crop lengths. This function is available when not printing the top and bottom images that are pre-specified in a higher-level application.
Page 140: Text Processing
Software Manual 4.12. Text Processing The Text Processing configuration panel allows for setting options that enable the TSP100 to detect certain “Text Keys” and modify each receipt based on them. This panel also allows for configuring how the TSP100 futurePRNT will detect the end of page so that receipts can be properly buffered and modified in full.
Page 141: Text Triggers
Software Manual 4.12.1. Text Triggers In order to modify receipts based on their contents, Text Keys that will serve as triggers must be inputted. 1 Click the “Add Key” button to input a new Text Key. 2 When satisfied with the contents of the Text Key, click “OK” to add it to the Text Key list.
Page 142 Software Manual 3 The default character code is 1252 (Windows Latin 1). If you cannot do a search or the replaced character string has become corrupted, change the character code as necessary. * See Windows 1252 Code Table in “4.16 Printer Font”. 4 With the proper Text Key selected, Configuration options are enabled.
Page 143 Software Manual Depending on the option that you select, the printer performs one of the following operations. Add Multiple Coupons: Multiple coupons are added. The number of coupons that are added equals the number of text keys that are detected. Add Single Coupon: When multiple text keys are detected, only a single coupon is added for multiple copies of the same graphic data.
Page 144: End
Software Manual 4.12.2. End Page Detect It is possible to change how the TSP100 futurePRNT detects the end of the receipt. ■ Cut or Feed to Tearbar Commands Select this option if the TSP100 futurePRNT should treat the “Cut” command as a signal that the receipt has ended.
Page 145: Barcodes
Software Manual 4.13. Barcodes Printing of barcodes can be accomplished using any of three methods. The preferred method is to print barcodes using control codes by programming directly to the printer. The second method is to print barcodes using the embedded printer font for the barcode. The final method is to print barcodes using a barcode font that resides on the host PC.
Page 146: Itf Bearer Bars
Software Manual 4.13.1. ITF Bearer Bars Bearer bars help to insure that a barcode is not misread by preventing partial scanning. ITF Barcode without Bearer Bars ITF Barcode with Bearer Bars 4.13.2. UPC-A Guard Bar Length Guard bars act as reference points for the scanner to aid in proper reading of the barcode. UPC-A Barcode without Guard UPC-A Barcode with Guard Bars Extended...
Page 147: Jan/Ean-13 Guard Bar Length
Software Manual 4.13.3. JAN/EAN-13 Guard Bar Length Guard bars act as reference points for the scanner to aid in proper reading of the barcode. JAN/EAN-13 Barcode without JAN/EAN-13 Barcode with Guard Bars Extended Guard Bars Extended 2 mm 4.13.4. CODE39 Guard Bar Length <Star Line Mode Only> Guard bars act as reference points for the scanner to aid in proper reading of the barcode.
Page 148: Code39 Character Set
Software Manual 4.13.5. CODE39 Character Set <Star Line Mode Only> Specify the character set for CODE39 barcode. Selecting "Standard" sends only Code39 standard code data. Selecting "Extended" sends all code data. The default is "Standard".

Page 149: Journaling, And Printing Of Multiple Customized Copies
Software Manual 4.14. Journaling, and Printing of Multiple Customized Copies Use this page to set up journaling and multi-copy printing.
Page 150: Multi-Copy
Software Manual 4.14.1. Multi-Copy Select the "Automatic Multiple Copies" checkbox when copying a receipt separately from the master. This function is helpful when issuing a receipt as a shop's or customer's copy. You can print up to four copies, and specify the header, footer, or merge image for each copy. Furthermore, you can only select the images that are pre-registered in "4.8.1 Adding an Image".
Page 151: Journal
Software Manual 4.14.2. Journal A journal is a function that saves printed data. To use this function, select the "Enable Journal" checkbox. Follow the steps below to display and print saved data. Click “View Journal”. The following Journal window appears. Click “Search”...
Page 152 Software Manual The following dialog box then appears. Enter the date to end searching, and click “OK”. This will search for the data printed in the specified period when the journal function is enabled.
Page 153 Software Manual Dates will appear as shown in the following window. Click a desired date to check data details in the preview screen. If you wish to print an image, click “Print”. Journal print data is saved into the following folder. <System Drive>\Star\TSP100\Journal Note: When the driver utility application is updated from future PRNT CD 5.5 or earlier, the stored data for canceled printing is transferred to the above folder.
Page 154: Vertical Mounting
Software Manual 4.15. Vertical Mounting If you are setting the printer upright or mounting it on the wall, check this checkbox to invert the printing. If the button is checked, receipts are printed bottom-to-top so that they are easier to present correctly to the customer.
Page 155: Printer Font
Software Manual 4.16. Printer Font <Star Line mode only> You can convert device fonts of the printer into a standard Windows font for printing. Also, you can increase the default 24-dot character height to 35-dot for printing. Click the “Printer Font” tab on the left side of the window.

Page 156 Software Manual Windows 1252 Code Table Windows-1252 (CP1252) x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF NUL SOH STX ETX EOT ENQ ACK BEL BS TAB LF DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS "...
Page 157: Virtual Tcp/Ip Ports
Software Manual 4.17. Virtual TCP/IP Ports <TSP100LAN / TSP100IIIW / TSP100IIILAN Only> By setting up virtual TCP/IP ports, you make it possible for your applications to directly designate TCP/IP sockets. Virtual ports are registered under the operating mode under which they are generated.

Page 158: Creating A Virtual Tcp/Ip Port
Software Manual 4.17.1. Creating a Virtual TCP/IP Port Use the following procedure to create a virtual TCP/IP port. 1. Click Add Port. 2. At the following dialog, enter the output port number used by the application. (If the output port number is 9100, for example, enter "9100".) Then click [OK].
Page 159: Tcp/Ip Port Emulator Service Setting
Software Manual 4.17.2. TCP/IP Port Emulator Service Setting Select the Startup Type for the emulator service. To enable use of the emulator service, set the Startup Type to either Manual or Automatic. If you select Automatic, the port emulator service will start automatically when the system starts up. If you select Manual, the service will not start until you click the [Start] button.
Page 160: Print Job Routing (Write Printer)
Software Manual 4.18. Print Job Routing (Write Printer) <ESC/POS Mode Only> Click the “Write Printer API” tab in the left pane of the window. When printing in the ESC/POS mode, use one of the following methods. ・ Select the "Enable ESC/POS Routing" checkbox on "Print Job Routing". ・...

Page 161: Guidelines For Printing Documents
Software Manual 5. Guidelines for Printing Documents ○ There is no need to set paper margins with this driver. Set all margins to 0. ○ This driver supports 4 predefined custom paper sizes and user-defined paper sizes. Feel free to use user-defined sizes as needed.
Page 162: Restrictions And Cautions
Software Manual Select the “Use printer metrics to lay out document” check box. Then click the “OK” button. Open Word’s File menu, and select Save to save the document. When the page settings are changed, the option settings may return to the original settings.
Page 163: Guidelines For Using Ethernet Environment
Software Manual 6. Guidelines for Using Ethernet Environment 6.1. Manually Setting a Temporary IP Address You can use the following procedure to set a temporary IP address for a TSP100LAN printer. Use of a temporary address will allow you to connect to a printer that does not yet have an IP address setting. 1.
Page 164: Manually Setting An Ip Address (Using The Tsp100Lan Telnet Utility)
Software Manual 6.2. Manually Setting an IP Address (Using the TSP100LAN Telnet Utility) You can use the telnet command to connect directly to a TSP100LAN printer. ■ Begin with the following preliminary steps to ensure that Telnet is enabled. 1. From the [Start] menu, open the [Control Panel]. 2.
Page 165 Software Manual 5. If [Telnet Client] is not yet checked, place a check next to it. Then click [OK]. 6. If you had to add the check in the previous step (if Telnet Client was not already checked to begin with), you must now restart your computer.
Page 166 Software Manual To manually set the IP address, proceed as follows. Open a Command Prompt window. At the Windows Start menu, select [All Programs]  [Accessories] click [Command Prompt] . (If using Windows 10, [All Apps]  [Windows System] click [Command Prompt].) Use the telnet command to connect to the printer you wish to set.
Page 167 Software Manual The following menu appears. 1) IP Parameters Configuration 2) System Configuration 3) Change Password 96) Display Status 97) Reset Settings to Defaults 98) Save & Restart 99) Quit Enter Selection: Enter the number corresponding to the action you wish to carry out. When you have finished making settings, select 98 (Save and Restart) and then select either 1 (Save &...
Page 168: Restrictions And Cautions
Software Manual 7. Restrictions and Cautions Below is the restrictions and cautions for this version. Please read through and have well understanding before use. ■ Emulation: Star Line mode - Barcode Printing when Horizontal Compress & Two Color Printing is selected. In this case, please do not print Barcode and Text within the same line.
Page 169 Software Manual ■ Emulation in common - Text Triggers in Text Processing When you register multiple text keys, character strings that you can use when you select "Replace with alternate text" have the following limitations. - You cannot use strings that have already been used. - You cannot use substrings of strings that have already been used.
Page 170 Software Manual - Time out value using Virtual Serial Port Depending on the setting of theVirtual Serial Port, the time out value willl be different. Refer to the SDK of the Virtual Serial Port in this CD to change it. - Virtual Serial Ports The Virtual Serial Port Emulator is not suppoprted by OPOS.
Page 171 Software Manual - Preview and On Demand When On Demand is in use, Preview function cannot be used. - Ethernet Setup Tool After generating the printer queue using the Ethernet Setup Tool, the "Complete" message may appear behind other windows. Star recommeds to close other windows first before using the Ethernet Setup Tool.
Page 172 Windows 8.1 support Rev. 6.1 9/16/2015 Added Windows 10 support Rev. 6.2 10/30/2015 Added ESC/POS support for Star Cloud Services Added TSP100IIIW, TSP100IIILAN Rev. 7.0 12/24/2015 Function addition of TSP100LAN Ethernet setting tool Windows XP and Windows Vista end of support...
Page 173 http://www.starmicronics.com/support/...

This manual is also suitable for:

Tsp100iiiw Tsp100eco Tsp100u/pusb Tsp100gt Tsp100lan

Star Micronics TSP100IIILAN Software Manual

1 Installation and Uninstallation

2 Features

3 Windows Printer Driver Usage

4 TSP100 Configuration Application

5 Guidelines for Printing Documents

6 Guidelines for Using Ethernet Environment

7 Restrictions and Cautions

8 Release History

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Star Micronics TSP100IIILAN

Summary of Contents for Star Micronics TSP100IIILAN

This manual is also suitable for:

Table of Contents