Tailoring Performance; Information Readouts - Martin MX-10 User Manual

Tailoring performance

M O V E M E N T
The MX-10 provides the three options for optimizing movement to suit different applications.
PA TI , the pan and tilt invert menu, allows you to swap the pan and tilt channels (
P I N V > O N
(
some fixtures to mirror the performance of others with the same DMX address, or when fixtures are not oriented as
programmed.
P T S P , the pan/tilt speed menu, provides 2 settings:
FA ST provides better performance in applications where speed is most important.
SC UT , the shortcuts setting, determines whether the color and gobo wheels scroll past open when changing positions.
When set to
position. The wheels do not scroll past open when
D I S P L A Y
The display menu (
remain lit, or OFF to extinguish the display two minutes after the last key press.
To flip the display for easier reading, press [up] and [down] simultaneously.
The display intensity setting (
dimming of the display using the built-in light sensor, or manually select an intensity level from 10 to 100.
L A M P P O W E R
There are two settings that modify lamp control: Automatic Lamp On (
( P E RS > DL oF
There are three options for automatic lamp control:
off until a lamp-on command is received from the controller. When
the fixture is powered on. When
data, and it extinguishes automatically 15 minutes after DMX data is lost. When ALON is either ON or DMX, lamp
strike timing is determined by the fixture address to prevent all lamps from striking at once.
The DMX Lamp-Off setting effects how the lamp can be turned off. When
off by sending a DMX value from 248 to 255 on channel 1 for five seconds. When
command will not work unless special conditions are met. Refer to the DMX protocol.
R E S E T
The fixture can be reset from the controller if DMX reset (
command will not work unless special conditions are met. Refer to the DMX protocol.
D E F A U L T S E T T I N G S
The fixture can be reset to its factory default settings by selecting

Information readouts

P O W E R - O N H O U R S
Read the total number of hours the fixture has been on since fabrication (
number of hours on since the counter was last reset (
maintenance intervals. Press [up] for 5 seconds while displayed to reset.
L A M P H O U R S
Read the total number of lamp hours since fabrication (
hours since the counter was last reset (
lamp. Press [up] for 5 seconds while displayed to reset.
12
), and invert tilt movement (
O N , the wheels can "take a shortcut" and scroll through open when this is the shortest path to the next
PE R S> dI S P ) determines whether the display remains lit or not. Select
P E R S > d I N T
).
A LO N is set to
I NF O >T I ME > L H R> R SE T
T I N V > O N
). These options can be useful in situations where you want
F A S T and N O R M
SC U T is set to OFF.
) controls display brightness. You can select
O N , O F F , and D M X
A LO N
D M X , the lamp strikes automatically when the fixture receives DMX
P E R S > d R E S
dF SE > FA C T> LO A d.
I N F O > T I M E > H R S > R S E T
I N FO >T I ME > L H R> TO T L
MX-10
S W AP > O N ), invert pan movement
. N O R M is best for most applications.
O N to have the display
A U T O
P E R S > A L O N
) and DMX Lamp-Off
. When A L O N is O F F , the lamp remains
is ON , the lamp strikes automatically after
dL O F is O N , lamp power can be switched
d L O F is O F F
) is O N . If DMX reset is
I NF O >T IM E >H R S> TO T L
). This can be used to track
), and the number of lamp
). Reset this counter after installing a new
for automatic
, the lamp-off
O F F , this
), and the