Martin MAC Aura XB Service Manual
Hide thumbs Also See for MAC Aura XB:

Advertisement

SERVICE MANUAL
MAC Aura XB
Revision A, 05-15-2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MAC Aura XB and is the answer not in the manual?

Questions and answers

carlos
March 31, 2025

tengo un caso **** una mac aura xb **** problemna de que unos de los motores al inicio de hacer el reset no hace el stop le e cambiado los sensores y le echo un reflluo al procesador pero sigue igual ya seria tema de software?

1 comments:
Mr. Anderson
March 31, 2025

If one of the motors on a Martin MAC Aura XB does not stop during the reset after changing the sensors and reflowing the processor, a likely software issue could be corrupt or missing calibration values on one of the boards.

This answer is automatically generated

Summary of Contents for Martin MAC Aura XB

  • Page 1 SERVICE MANUAL MAC Aura XB Revision A, 05-15-2017...
  • Page 2: Table Of Contents

    Replacing the yoke bracket ....................................19 Base ........................................21 Replacing the base fan ......................................21 Replacing the PSU ....................................... 22 Maintenance ................................25 Cleaning the product ....................................25 Conditions ......................................25 Maintenance schedule ..................................26 MAC Aura XB - Revision A, 05-15-2017 2 of 27...
  • Page 3: General Information

    • ESD mat and wristband. Figure 2: Tools Take the necessary precautions to prevent static electricity from damaging the product during modification or repair. Figure 3: ESD mat and wristband MAC Aura XB - Revision A, 05-15-2017 3 of 27...
  • Page 4: Spare Parts

    Service manual Spare parts For an overview of the spare parts and spare part numbers of MAC Aura XB, refer to martin.com Login with your user login details. Search for “MAC Aura XB”. Clik “Partfinder: Layered” (1). Figure 4: PartFinder: Layered...
  • Page 5 Most of the wires that are connected to the mainboard are small. Use a small flatheaded screwdriver to loosen the connectors. NOTE! Never disconnect the connectors by pulling the wires. Figure 7: Loosening the connectors MAC Aura XB - Revision A, 05-15-2017 5 of 27...
  • Page 6: Troubleshooting

    The fixture does not show the correct color. The fixture does not have the same intensity. The fixture does not have the same intensity. The fixture does not show the correct color. MAC Aura XB - Revision A, 05-15-2017 6 of 27...
  • Page 7 The beam angle is not the same as the other The wire connection is faulty. Replace the wire set. fixtures’. The main PCB is faulty. Replace the main PCB. MAC Aura XB - Revision A, 05-15-2017 7 of 27...
  • Page 8: Wiring Diagram

    Service manual Wiring diagram Figure 8: Wiring diagram, MAC Aura XB Hybrid MAC Aura XB - Revision A, 05-15-2017 8 of 27 8 of 27...
  • Page 9: Repair And Maintenance

    Remove the four TX20 screws (2) that hold the fan. Remove the fan. To replace the fan, follow the procedure in reverse order. Figure 10: Removing the screws Figure 11: Removing the screws MAC Aura XB - Revision A, 05-15-2017 9 of 27...
  • Page 10: Replacing The Main Lcd Display

    (3) below the main PCB. Remove the screws to loosen the LCD display. To install the new display, follow the procedure in reverse order. Figure 14: LCD display, ribbon cable and screws MAC Aura XB - Revision A, 05-15-2017 10 of 27...
  • Page 11: Replacing The Thermo Switch

    88V supply to the main PCB. Remove the main PCB. See “Replacing the main LCD display” on page 10. Remove the wires (1). Figure 17: Thermo switch MAC Aura XB - Revision A, 05-15-2017 11 of 27...
  • Page 12: Replacing The Front Lens

    The lens, pixel boards, heat sink, mainboard and fan are assembled in a complete assembly. Disconnect all the wires to this assembly and place them on the table before you begin. Figure 19: Front lens MAC Aura XB - Revision A, 05-15-2017 12 of 27...
  • Page 13 Pixelboard secondary Insulation paper Enclosure plate Light rod assembly Zoom motors Pixelboard primary Thermal pad Heatsink Thermo switch Air guide Mainboard LCD display Figure 20: Exploded view of head assembly MAC Aura XB - Revision A, 05-15-2017 13 of 27...
  • Page 14: Replacing The Diffuser Plate

    To install the new diffuser plate, follow the procedure in reverse order. NOTE! Make sure to align the diffuser plate according to the alignment markers. Figure 23: Diffuser plate taps MAC Aura XB - Revision A, 05-15-2017 14 of 27...
  • Page 15: Replacing The Secondary Pixel Board

    To mount a new light rod, follow the procedure in reverse order. NOTE! Remember to wear gloves when you replace the light rods to avoid leaving grease and residue on them. Figure 26: Light rod MAC Aura XB - Revision A, 05-15-2017 15 of 27...
  • Page 16: Replacing The Primary Pixel Board

    To install the new primary pixel board, follow the PL39 procedure in reverse order. NOTE! Make sure to add Loctite 243 to the PL44 screws before fastening them. PL43 Figure 28: PCB connections MAC Aura XB - Revision A, 05-15-2017 16 of 27...
  • Page 17: Yoke

    Remove the two TX10 screws (4). Remove the tilt sensor PCB. To install the new tilt sensor PCB, follow the Figure 31: Tilt sensor and belt tensioner procedure in reverse order. MAC Aura XB - Revision A, 05-15-2017 17 of 27...
  • Page 18: Adjusting The Tilt Timing Belt

    Remove the two TX10 screws (1). Remove the pan reset sensor PCB (2). To install a new pan reset sensor PCB, follow the procedure in reverse order. Figure 34: Replacing the pan reset sensor PCB MAC Aura XB - Revision A, 05-15-2017 18 of 27...
  • Page 19: Replacing The Pan Positioning Sensor Pcb

    (7). 13. Remove all the parts attached to the yoke bracket, such as pan motor, tilt motor, belt tensioners, rubber grommets and the two sensors. Figure 37: Yoke MAC Aura XB - Revision A, 05-15-2017 19 of 27...
  • Page 20 19. Remove the yoke bracket. 20. To install the new yoke bracket, follow the procedure in reverse order. Figure 39: Replacing the gobo rotation belt MAC Aura XB - Revision A, 05-15-2017 20 of 27...
  • Page 21: Base

    PSU PCB (3). Disconnect the connector (4) before you pull away the cover. Figure 42: Connector for the fan wire MAC Aura XB - Revision A, 05-15-2017 21 of 27...
  • Page 22: Replacing The Psu

    Disconnect the 6-pin 24V 88V connector (2) from the PSU board. Disconnect the white DMX connector (3) from the PSU board. Remove the M4 (4) nut that holds the ground connection. Figure 45: Disconnecting the connectors MAC Aura XB - Revision A, 05-15-2017 22 of 27...
  • Page 23 Remove the eight TX10 screws that hold the base connectors. Figure 47: Removing screws 10. Disconnect the blue and brown wires (7) from the PSU board. Figure 48: Mains wires MAC Aura XB - Revision A, 05-15-2017 23 of 27...
  • Page 24 FET to the heat sink to the base frame. 13. Remove the PSU. 14. To install a new PSU, follow the procedure in reverse order. Figure 50: Screws holding the FET MAC Aura XB - Revision A, 05-15-2017 24 of 27...
  • Page 25: Maintenance

    Check again at frequent intervals. This procedure will allow you to assess cleaning requirements in your particular situation. If in doubt, consult your Martin™ by Harman dealer about a suitable maintenance schedule. Work in a clean, well lit area. Use gentle pressure only when cleaning.
  • Page 26: Maintenance Schedule

    Service manual Maintenance schedule MAC Aura XB - Revision A, 05-15-2017 26 of 27 26 of 27...
  • Page 27 Martin™, Harman™ and all other trademarks in this document pertaining to services or products by Martin Professional™...

Table of Contents

Save PDF