Motorola 2.1 Networking Setup Manual page 9

Figure 4-27 Antenna Heights.............................................................................................................4-18
Figure 4-28 Antenna Patterns ...........................................................................................................4-19
Figure 4-29 Poor Install Example 1 ...................................................................................................4-19
Figure 4-30 Poor Install Example 2 ...................................................................................................4-20
Figure 4-31 Poor Install Example 3 ...................................................................................................4-20
Figure 9-1 Initial Power Connector Package Contents........................................................................9-10
Figure 9-2 Required Items ...................................................................................................................9-10
Figure 9-3 Feed flying lead cable through components ......................................................................9-11
Figure 9-4 Attach flying lead cable to the plug.....................................................................................9-11
Figure 9-5 Assemble plug ....................................................................................................................9-12
Figure 9-6 Arrange the components ....................................................................................................9-12
Figure 9-7 Tighten plug........................................................................................................................9-13
Figure 9-8 Finished Power Connector and Cable Assembly...............................................................9-13
Figure 9-9 European Power Connector Front View.............................................................................9-14
Figure 9-10 European Power Connector Side View .........................................................................9-14
Figure 9-11 Top View of European Power Connector Showing Access Screw................................9-15
Figure 9-12 Side View of Plug Showing Detail of the Stress Relief Bar............................................9-15
Figure 9-13 Side View of Plug Contents and Plug Shell ...................................................................9-15
Figure 9-14 Initial Power Cable View ................................................................................................9-16
Figure 9-15 Side View of Plug Showing Detail of the Stress Relief Bar and Screws........................9-16
Figure 9-16 Power cable pulled through the Plug Shell and Under the Stress Relief Bar ................9-17
Figure 9-17 Wire Base is Not Visible on the Right Side of the Stress Relief Bar..............................9-17
Figure 9-18 Stress Relief Bar Screws ...............................................................................................9-18
Figure 9-19 Power Cable Designations.............................................................................................9-18
Figure 9-20 Position of the Neutral, Line, and Earth Ground Screws ...............................................9-18
Figure 9-21 Correct Position of the Cable Wires Attached to the Plug. ............................................9-19
Figure 9-22 Finished Plug .................................................................................................................9-19
Figure 9-23 Front View of the Australian Power Connector Plug......................................................9-20
Figure 9-24 Side View of the Australian Power Connector Plug.......................................................9-20
Figure 9-25 Front View of the Australian Power Connector Plug with Opened Sides ......................9-21
Figure 9-26 Side View of the Australian Power Connector Plug with Opened Sides .......................9-21
Figure 9-27 Inside View of the Australian Power Connector Plug ....................................................9-21
Figure 9-28 Power Cable with Wire Designation...............................................................................9-23
Figure 9-29 Inside View Pointing out Strain Relief Bar and Screws .................................................9-23
Figure 9-30 Correct Wire Positioning on Either Side of Screw Well .................................................9-24
Figure 9-31 Correct Position of the Cable Below the Strain Relief Bar.............................................9-24
Figure 9-32 Correct Wire Attachment to the Terminal Plug ..............................................................9-25
Figure 9-33 Position of Access Screw When the Plug is folded Half Way........................................9-25
Figure 9-34 Configuring a Wireless Client Adapter with a Static IP Address....................................9-26
Figure 9-35 Creating a Profile ...........................................................................................................9-27
Figure 9-36 Verify Backdoor Access by Performing a Ping ..............................................................9-28
Figure 9-37 Select "Continue to Website" in Internet Explorer..........................................................9-29
Figure 9-38 Login to the MOTOMESH Duo 2.1 Backdoor ................................................................9-29
Figure 9-39 General Settings Tab in the Web User Interface ...........................................................9-30
Figure 9-40 MOTOMESH DUO 4300 - 49 AC and DC Device Product Labels (Samples)...............9-31
Figure 9-41 MOTOMESH DUO 4300 - 58 AC and DC Device Product Labels (Samples)...............9-31
Figure 9-42 MOTOMESH DUO 4300 - 54 AC and DC Device Product Label ..................................9-31
ix