Panasonic AJ-PX800G Operating Instructions Manual page 154

10 Remote control display in an IP connection
The remote control status in an IP connection is displayed when main menu → [NETWORK SETUP] → [NETWORK FUNC] → [IP REMOTE] is set
to [ENABLE].
f [IP REMOTE] (lashing): Displayed during connection waiting status in an IP connection.
f [IP REMOTE] (illuminated): Displayed when remote control is possible in an IP connection.
11 USER button information display
When the USER button is pressed, "USER button name: assigned function name" is displayed for three seconds. The USER button name is
indicated by [UM], [U1], or [U2].
12 Focus bar display
Displays the following items in the bottom left of the viewinder. The high-frequency component of the video is displayed in a numerical value.
f White bar: Focus bar display
f Green line: Peak display
13 Date and time display
Displayed in the order of "mmm dd yyyy hh:mm:ss".
The display/hide status differ depending on the settings in the main menu → [DISPLAY SETUP] → [DATE/TIME].
f mmm: Month (JAN (January), FEB (February), MAR (March), APR (April), MAY (May), JUN (June), JUL (July), AUG (August), SEP (September),
OCT (October), NOV (November), DEC (December))
f dd: Date
f yyyy: Year (2000 to 2037)
f hh: Hour
f mm: Minute
f ss: Second
14 Audio level meter display
Switches between level meter display of audio output channels 1/2 and 3/4 while holding down the USER button where [LEVEL METER] is
assigned.
The peak display on right edge is displayed in red during peak over.
The standard level display will switch as follows depending on the main menu → [AUDIO SETUP] → [RECORDING CH SETTING] → [HEADROOM]
setting.
f When set to [20dB]
f When set to [18dB]
15 Digital zoom display
Displays the digital zoom ratio.
f [D2×]: two times
f [D4x]: four times
16 Y GET brightness display
In the Y GET mode, the image level in the frame displayed near the center of the screen is displayed as 0% to 109%.
17 ND ilter display
Displays the selected ND ilter.
When [ND−] is displayed, the <ND FILTER> dial is shifted to position out of <1> to <4>. Check the position of the <ND FILTER> dial.
18 Shutter speed display
Displays the shutter speed. When synchro scan is performed, the display shows the content set in the main menu → [SCENE FILE] → [SYNC SCAN
TYPE] (time (minutes) or open angle image).
19 <WHITE BAL> switch position display
Displays the position currently selected. Also, the white balance operation is indicated when the automatic white balance is preset. In auto tracking
white balance (white balance with automatic tracking) mode, [ATW] is indicated, and when auto tracking white balance mode is locked, [LOCK] is
indicated.
20 Gain display
Displays the gain value of the image ampliier conigured.
[AGC] is displayed when auto gain control is active.
21 Iris display
Displays the F value.
[NC] is displayed when a lens connector is not connected.
22 Zoom position display
Displays the zoom position from [Z000] (maximum wide angle) to [Z999] (maximum zoom). Note, however, that this item is not displayed in the case
of lenses without a zoom position return even if it is set to be displayed.
When a serial lens is connected, the display unit can be changed in main menu → [DISPLAY SETUP] → [ZOOM/FOCUS].
23 Focus control information display
Displays the focus control information from [99] to [00]. This item is not displayed, when other than a serial lens is connected or a lens that has no
return of focus control information is connected.
When a serial lens is connected, the display unit can be changed in main menu → [DISPLAY SETUP] → [ZOOM/FOCUS].
Chapter 8 Display — Screen status display
-20dB
CH1
CH2
-18dB
CH1
CH2
– 154 –
0dB
0dB