Table of Contents
Advertisement
2. Build the plane according to the instructions. Do not
alter or modify the model, as doing so may result in an
unsafe or unflyable model.
3. Use an R/C radio system and components that are in first-
class condition. The FlatOut Flatana ARF requires
specialized radio gear. Refer to the "DECISIONS YOU
MUST MAKE" section to get an accurate description of the
specialized gear required.
4. You must properly install all R/C and other components so
that the model operates correctly on the ground and in the air.
5. You must test the operation of the model before every
flight to insure that all equipment is operating, and that the
model has remained structurally sound. Be sure to check
connectors often and replace them if they show signs of
wear or fatigue.
Note: We, as the kit manufacturer, provide you with a top
quality kit and great instructions, but ultimately the quality
and flyability of your finished model depends on how you
build it; therefore, we cannot in any way guarantee the
performance of your completed model, and no
representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow directions to end
up with a well-built model that is straight and true.
If you're not already an AMA (Academy of Model
Aeronautics) member, we highly recommend that you join.
In addition to providing liability protection while operating
under the AMA Safety Code, the AMA is the governing body
of model aeronautics in the United States and fights for your
rights as a member of the modeling community. You must
also be an AMA member to fly at R/C clubs chartered by the
AMA–most of which are.
Contact the AMA at the address or toll-free phone
number below.
DECISIONS YOU MUST MAKE
In the hands of a capable pilot the FlatOut Flatana ARF is
an impressive 3D performer. But for the FlatOut Flatana
ARF to perform to its full potential, it must be properly
equipped with all the right gear (servos, batteries, receiver,
speed control). There may be more than one type and brand
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302
Tele: (800) 435-9262
Fax (765) 741-0057
Or via the Internet at:
http://www.modelaircraft.org
of radio equipment that can be used, but based on extensive
testing, following is the equipment we recommend so you
can get the most performance out of your FlatOut Flatana
ARF and assemble it as shown in this instruction manual.
Transmitter
With a standard, four-channel radio, the FlatOut Flatana
ARF is capable of all the basic 3D maneuvers. However,
some advanced pilots who are already familiar with handling
"flat foamies" may prefer to fly the FlatOut Flatana ARF with
a computer radio capable of endpoint adjustments (for fine-
tuning control throws), exponentials (for "softening" the
throws near the center of the travel), and various mixing
functions (such as rudder-to-elevator mixing for extended
knife-edge flight).
The FlatOut Flatana ARF requires three, sub-micro servos
with a maximum weight of .3 oz [9g] each and a minimum
torque rating of 15 oz-in. Futaba
connector) servos (FUTM0700) are ideal because they
meet the torque and weight requirements and have a micro
connector that is compatible with the Futaba Ultra Micro
receiver. Although there may be other servos that will
physically fit in the model, those outside of the
recommended weight and torque specifications will
adversely
affect
flight
recommended. Note: During assembly when it's time to
mount the servos, you will be instructed to glue them in. Do
not be alarmed as this is a common practice with this type
of lightweight, high-performance model. Should servo
removal ever be necessary for repair, replacement or
transfer to another model this can be done by prying them
out with a hobby knife or a small screwdriver.
The lightest, four-channel receiver is recommended and
must be compatible with whatever servos will be used (not
all servos are compatible with all receivers–even servos and
receivers within the same brand). The Futaba R-124F Ultra
Micro receiver is recommended and is compatible with the
3108M servos recommended. Note: Futaba receivers are
sold on high and low bands and come without crystals.
Following are the order numbers for the R-124F receiver
and compatible crystals:
(Channels 11-35)
R124F Receiver
Crystal
** Replace the "**" in the order number for the crystals with
the preferred channel number. For example, if you want to fly
3
Servos
®
S-3108M (micro
performance
and
Receiver
Low Band
High Band
(Channels 36-60)
FUTL0438
FUTL0439
FUTL62**
FUTL63**
are
not
Advertisement
Table of Contents
