Table Of Contents - jablotron JA-82K OASiS Installation Manual

Contents:
1 Control panel architecture.................................. 3
1.1 Required system configuration
2 Preparing the control panel for installation ........ 3
3 Control panel main board................................... 3
3.1 Main board terminal description:
3.2 Hard-wired inputs on the main board
3.3 Installation of additional hard-wire input modules
3.4 Radio module installation
3.5 Y,X,V communicator module installation
3.6 Control panel memory chip
3.7 Wired keypad connection
3.8 Control panel resetting
4 Control panel power supply ............................... 5
4.1 Backup battery connection
4.2 Power supply connection
4.3 Powering-up the control panel for the first time
5 OASiS wireless devices ..................................... 6
5.1 Enrolling wireless devices to the control panel
5.2 Testing enrolled wireless devices
5.3 Signal strength measuring
5.4 Erasing enrolled devices
5.5 Enrolling the control panel to UC and AC modules
6 Control panel programming ............................... 7
6.1 Exit delay time
6.2 Entrance delay time
6.3 Alarm duration time
6.4 PGX and PGY functions
6.5 Changing telephone numbers in maintenance mode
6.6 Radio interference indication
6.7 Radio communications supervision
6.8 RESET enabled
6.9 Enrollment to a sub control panel for setting control
6.10 Master code reset
6.11 Enrollment to other devices (UC, AC)
6.12 Setting (Arming) without an access code
6.13 Triggered-detector indication
6.14 Confirmation of intruder alarms
6.15 Exit delay beeps
6.16 Exit delay beeps while partially setting (arming)
6.17 Entrance delay beeps
6.18 Setting (arming) confirmed by wired-siren chirp
6.19 Sirens always sound during audible alarms
6.20 Wireless siren alarm enabled (IW and EW)
6.21 Bypass user approval
6.22 Final-door detectors
6.23 Partial setting (arming) or system splitting
This manual is valid for control panel JA-82K
The control panel can be configured by a PC running OLink software.
JA-82K control panel installation manual
6.24 Automatic summer time (daylight saving time)
6.25 Pulse reaction of tamper sensors
3
6.26 Operating the PG outputs using
6.27 Permanent alarm status display for a set system
6.28 Tamper alarm if unset
3
6.29 Recording PG output activation to memory
4
6.30 Engineer reset
4
6.31 Social alarm feature
4
6.32 Annual check notification
4
6.33 Only single alarm indication
4
6.34 Setting (arming) by service code
5
6.35 Audible panic alarm
5
6.36 Higher control-panel receiver-sensitivity
6.37 Access by code plus card
5 6.38 Audible 24 hour intruder alarm
5 6.39 Service mode only with service and user code
5 6.40 Device reactions and section assignment
6.41 Code/card reactions and section assignment
6.42 Enrollment by keying in production codes
6
6.43 Automatic setting / unsetting schedule
6
6.44 Changing the service code.
6
6.45 Go to maintenance mode
6
6.46 Setting the internal clock
6
6.47 Editing keypad text
6.48 Recommended settings
7
7 Operating the system....................................... 13
7
7.1 The system keypad
7
7.1.1 Keypad indicators: .........................................................13
7
7.1.2 LCD display ...................................................................13
7
7.1.3 Keypad display sleep-mode...........................................13
7
7.1.4 Keys...............................................................................13
7
7.1.5 Functions beginning with the
7
7.2 Programming access codes and cards
7
7.3 Setting and unsetting (arming/disarming) the system
8
7.4 Maintenance Mode
8
7.4.1 Displaying which user/card positions are occupied .......14
8
7.4.2 Bypassing devices .........................................................14
8
7.4.3 Protecting a car near the system ...................................14
8
8 Operating/programming the system by PC...... 15
8
8 9 Basic guidance for installers ............................ 15
8
10 Trouble-shooting .............................................. 15
8
11 Control panel technical specifications.............. 16
9
12 Control panel programming sequences........... 17
9
9 13 Programming access codes and cards............ 20
9
9
- 2 -
10
10
8 and 9 10
10
10
10
10
10
10
11
11
11
11
11
11
11
11
12
12
12
13
13
13
13
13
13
key ..........................14
14
14
14
MKH51102