Serial And Ir Insertion Connections; Control Connections; Switcher Reset; Power - Extron electronics DTP CrossPoint 84 IPCP Setup Gudie

Serial and IR Insertion Connections

RS-232 IR
1 2 3
4
Tx Rx G Tx Rx
SIG LINK OVER TP SIG LINK
XTP
RS-232 IR
DTP DTP
HDBT OUT Tx Rx G Tx Rx OUT
5
1 2 3 4 6
SIG
XTP
DTP
Figure 6. Serial and IR Insertion Connections
Over TP (Inputs 7 and 8) Ports — Plug serial RS-232
O
signals, modulated IR signals, or both into these 3.5 mm,
5-pole captive screw connectors to insert bidirectional
RS-232 and IR communications. See
connectors
on page 13 to wire the connectors.
Over TP (Outputs 3 and 4) Ports — Plug serial RS-232
P
signals, modulated IR signals, or both into these 3.5 mm,
5-pole captive screw connectors to insert bidirectional
RS-232 and IR communications. See
connectors on page 13 to wire the connectors.

Control Connections

COM 1 COM 2 COM 3 DIGITAL I/O
LAN 1
Tx Rx G RTS CTS Tx Rx G Tx Rx G 1 2 3 4 G
REMOTE
IR/SERIAL RELAYS eBUS
Tx Rx G 1 2 1 2 C 3 4 C +V +S -S G
R
S G S G PWR OUT = 6W LAN 2
Figure 7. IPCP Control Processor and Remote Port
IPCP control processor —The DTP CrossPoint 84 includes a built-
Q
in IPCP control processor that can control and monitor a variety of
external devices. The IPCP offers RS-232 and IR-based control,
relays, and digital I/O controls. See the IPCP Pro Series Setup Guide,
included in the carton with the switcher to make all connections and
to configure and operate the IPCP control processor.
Remote Port — Plug a serial RS-232 device into the matrix
R
switcher via this 3.5 mm, 3-pole captive screw connector for
remote control of the switcher (see
connectors on page 13 to wire the connector).

Switcher Reset

Switcher Reset button and LED — Initiates four levels of
S
matrix switcher reset. For different reset levels, press and hold
the recessed button while the switcher is running or while you
power up the switcher.
See the DTP CrossPoint 84 IPCP Series User Guide, available at
www.extron.com.

Power

T Power connector — Plug the switcher into a grounded AC source.
8 DTP CrossPoint 84 IPCP • Installation
4
S/PDIF
OUT
XTP
HDBT
RS-232 IR
8
Tx Rx G Tx Rx
LINK SIG LINK
OVER TP
XTP
RS-232 IR
DTP
IN Tx Rx G Tx Rx IN
Tx Rx
RS-232 and IR
Tx Rx
RS-232 and IR
LAN 3
RS-232 and IR

Additional Connector Information

RS-232 IR
G Tx Rx
RS-232 IR
G Tx Rx
REMOTE
Tx Rx G
RESET
HDMI connectors
Use a LockIt Lacing Bracket to securely fasten each HDMI cable to the
switcher as follows.
1. Plug the HDMI cable into
the panel connection.
3 3
2. Loosen the HDMI
connection mounting screw
from the panel enough
to allow the LockIt lacing
bracket to be placed over it.
1 1
The screw does not have to
be removed.
3.
Place the LockIt lacing
bracket on the screw
and against the HDMI
connector, then tighten
the screw to secure the
4 4
5 5
bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The
shield it fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI.
Le blindage auquel elle est attachée est très fin et peut
facilement être dénudé
4.
Loosely place the included tie wrap around the HDMI connector and
the LockIt lacing bracket as shown.
5.
While holding the connector securely against the lacing bracket, use
pliers or similar tool to tighten the tie wrap, then remove any excess
length.
DTP CrossPoint 84 IPCP • Installation
2 2
3
9