Dtp Input And Output Signals - Extron electronics DTP CrossPoint 84 IPCP Setup Gudie

Extron
TLP 1020T
AV
10" Tabletop
Control
TouchLink Pro
Ethernet
Network
Touchpanel
Ethernet
Extron
CATx Cable
DTP CrossPoint 84 SA up to 230' (70 m)
Scaling Presentation
Matrix Switcher with
DTP Extension
RS-232 IR
DTP CROSSPOINT 84
1 2 3 4 4
Tx Rx G Tx Rx
SIG LINK S/PDIF
OVER TP SIG LINK
OUT
XTP XTP
RS-232 IR
HDBT
DTP OUT Tx Rx G Tx Rx OUT DTP HDBT
100-240V ~ 2.0 A MAX
1 2 3 4 5 6 7
SIG LINK
XTP
DTP IN
50-60 Hz
HDMI
CATx Cable up to 230' (70 m)
DTP HDMI 230 Tx
Extron
DTP HDMI 230 Tx
POWER SIG LINK OVER DTP REMOTE
Transmitter 12V 1 2 3
--A MAX AUDIO
RS-232 IR CONTACT TALLY RS-232 RESET
INPUTS RGB, Y, R-Y, B-Y HDMI HDMI
DTP OUT Tx Rx G Tx Rx 1 2 3 G 1 2 3 + V Tx Rx G
Extron
DTP T USW 333 Inputs
DTP Transmitter
Table Microphones
Wireless
Microphones
Audio
100-240V ~ --A MAX 1 2 3 4 9 10 DMP 128 C
Camera
MIC +48V
1 2 3 4
5 6 7 8 11 12
50/60 Hz 5 6 7 8
1 2
Figure 1. Typical DTP CrossPoint Application
The switchers provide four mono microphone (mic)/line level inputs that
can be mixed with or across one or all audio outputs.
The switcher also features the built-in Extron IPCP Pro 350 control
processor, which has local area network (LAN) Ethernet ports, RS-232
and IR-based control, relays, and digital I/O controls that can control and
monitor a variety of external devices, such as projectors and lights.
The matrix switcher can be remotely controlled via Ethernet LAN ports on
the IPCP control processor, a serial port, or a USB port connection using
either the Extron Product Configuration Software, DSP Configurator
software, or the Simple Instruction Set (SIS).
2 DTP CrossPoint 84 IPCP • Introduction
Flat Panel Display Flat Panel Display
HDMI RS-232 HDMI RS-232
Extron Extron
OUTPUTS OUTPUTS OUTPUTS OUTPUTS
DTP HDMI DTP HDMI
OVER DTP OVER DTP
OVER DTP OVER DTP
RS-232 RS-232 IR IR 230 D Rx RS-232 RS-232 IR IR 330 D Rx
AUDIO AUDIO AUDIO AUDIO
Tx Rx G Tx Rx Tx Rx G Tx Rx Tx Rx G Tx Rx Tx Rx G Tx Rx
Receiver Receiver
Outputs
CATx Cable
up to 330' (100 m)
COM1 COM2 COM3 DIGITAL I/O
LAN 1 8 / 4
1
Tx Rx G RTS CTS Tx Rx G Tx Rx G 1 2 3 4 G
REMOTE L R
IR/SERIAL RELAYS eBUS
RESET
Tx Rx G 1 2 C 3 4 C
1 2 +V G D -S +S
R
CLASS 2 WIRING
S G S G PWR OUT = 6W LAN 2 LAN 3
RS-232 IR
+48V
8
Tx Rx G Tx Rx
L 1 R L 3 R L 5 R 1 1 3 L R L 3 R
1
OVER TP SIG LINK MIC/LINE
2
XTP 2 4 6 2 4
RS-232 IR L R L R L R 2 4 L R L R
3
4
IN
Tx Rx G Tx Rx DTP
EXP
Audio Audio
Microphones
Audio Audio
CATx Cable
up to 330' (100 m)
Extron Extron
Extron
SM 26
Surface Mount
Speakers
1 2 3 4
1 2 3 4 5 G 6 7 8 9 10 G
5 6 7 8
RS-232
11 12 13 14 15 G 16 17 18 19 20 G Tx Rx G EXP LAN
Extron
Audio Audio
DMP 128 C
Digital Matrix
1 2 3 Processor
4
3 LAN
Video Conference
Codec

DTP Input and Output Signals

RESET
The DTP inputs and outputs are proprietary signals that are created
within any of the Extron DTP Extenders systems and transmitted over a
single shielded twisted pair (STP) cable.
The DTP CrossPoint accepts DTP inputs from transmitting devices such
as the DTP T USW 333. Depending on the connected transmitting model,
it generates the DTP signal from a variety of video and audio inputs,
including HDMI, DVI, analog VGA, and embedded and analog audio. The
DTP signal can also include bidirectional RS-232 and IR control signals
from the connected transmitting and receiving devices or inserted locally,
on the DTP CrossPoint switcher.
Depending on the technology of the transmitting or receiving device,
DTP 330 or DTP 230, the TP inputs and outputs can travel up to 330 feet
(100 meters) or 230 feet (70 meters) without a loss of signal integrity.
DTP CrossPoint 84 IPCP • Introduction 3