Table of Contents
Advertisement
Quick Links
P
P P P
P
PECO
PECO
PECO
PECO
PECO
DESIGNED TO FIT:
900 SERIES BRIGGS & STRATTON
OPERATOR'S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0432
MODEL #: 37721231
PTO DRIVE
MODEL #: 37721232
MODEL #: 37721233
6.5HP BRIGGS & STRATTON
VANGUARD
PTO GRASS
COLLECTION
SYSTEM
2012 MODEL YEAR
TIGER CAT
52" & 61" VELOCITY
PLUS DECK
Advertisement
Table of Contents
Related Manuals for Peco 37721231
Summary of Contents for Peco 37721231
- Page 1 PECO COLLECTION SYSTEM DESIGNED TO FIT: 2012 MODEL YEAR TIGER CAT 52” & 61” VELOCITY PLUS DECK MODEL #: 37721231 PTO DRIVE MODEL #: 37721232 900 SERIES BRIGGS & STRATTON MODEL #: 37721233 6.5HP BRIGGS & STRATTON VANGUARD OPERATOR’S MANUAL...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Preparation Of Mower
Section II - INSTALLATION FOR USE Figure 2-1c 2-1 Preparation Of Mower Electric Engine Pulley Clutch Remove the rear shield and skid plate from the mower. Assembly Remove (3) 3/8” carriage bolts and (3) 3/8”-16 nuts from the rear bumper to disconnect the rear shield. Remove Flat Washer (2) 3/8”-16 carriage bolts (2) 3/8”-16 nuts from the skid plate to disconnect the skid plate from the frame of the... -
Page 7: Lower Frame Leg Installation
2-3 Lower Frame Leg Installation 2-4 Main Frame Assembly Installation Attach the left lower frame leg P#(B0725) and right lower Lift the main frame assembly P#(A1833) into position frame leg P#(B0724) to the rear bumper of the mower above the left and right lower frame legs. Secure the using (4) 3/8”-16 x 1”... -
Page 8: Lift Handle Installation
2-5 Lift Handle Installation Fasten the ball joint P#(K1442) to the end of the latch NOTE: Before continuing the lift handle installation, rod P#(A0620). Tighten the ball joint to approximately have someone assist you in turning the grass container half way down the threads on the latch rod. Attach the upside down. -
Page 9: Aluminum Grass Container Installation
2-6 Aluminum Grass Container Installation NOTE: It is recommended that (3) people assist in mounting the container. With three people available, two Figure 2-6b can lower the container onto the frame while the third person inserts the pivot pins P#(K0172) through the holes. -
Page 10: Aluminum Grass Container Parts List
A0560 ALUMINUM GRASS CONTAINER EXPLODED VIEW... -
Page 11: Exhaust Diverter Installation
On all engine models with an engine oil drain hose on 2-8 Exhaust Diverter Installation the right side of the engine, attach the existing J-hook to the rear bumper using the PTO mount assembly Insert the exhaust deflector P#(J0251) onto the end of hardware shown in Figure 2-9b. -
Page 12: Belt Installation And Adjustment
Connect the belt A58K P#(M0236) from the engine 2-11 Belt Installation and Adjustment pulley to the lower gear box pulley (Figure 2-11d). PTO MODELS ONLY Figure 2-11d Loosen the (4) bolts P#(K1191), (2) on each side, that Connect Belt secure the gear box assembly to the PTO assembly To Both Pulleys P#(A0623) (Figure 2-11a and 2-11b). -
Page 13: Pto Handle Assembly
2-12 PTO Handle Assembly 2-14 Outer Engine Mount Tube Installation Installation PTO MODELS ONLY Position the outer engine mount tube P#(B2220) as Attach the PTO handle P#(A1142) to the PTO assembly shown in Figure 2-14. Secure the outer engine mount using (3) 1/4”-20 x 3/4”... -
Page 14: Engine/Blower/Blade Assembly Installation
2-16 Engine/Blower/Blade Assembly 2-18 Boot To Mower Deck Installation Installation Position the boot plate P#(B0309) on top of the aluminum boot P#(E0012) as shown in Figure 2-18a. Place the engine blower blade assembly on top of the Secure the boot plate to the boot using (2) 3/8”-16 x 1” carriage bolts P#(K1182) and (2) 3/8”-16 nylon flange engine mount arm as shown in Figure 2-16a. -
Page 15: Hose Clamp Preparation
Step 3: Using a flat file or disc grinder, remove sharp 2-19 Hose Clamp Preparation edges from clamp cut in Step 2. Refer to Figure 2-19d. CAUTION Figure 2-19d Note: To prevent injury, wear safety gear when cutting or grinding hose clamps. Remove Sharp Edge From Hose Clamp The hose clamps P#(J1000), provided with your... -
Page 16: Length Of Hose Adjustment
2-20 Length Of Hose Adjustment 2-22 Lower Hose To Blower Cone Installation The hoses in steps 2-21 and 2-22 must be cut to fit your machine. Follow steps 2-21 and 2-22. do not cut the Slide a pre-assembled hose clamp P#(J1000) over both hoses until you have tried to fit them on your machine. -
Page 17: Impeller Blade Removal Replacement
2-24 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the 1 - Try carefully hitting the base of the impeller blade blower cone (#2) from the blower housing, located on (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 18: Weight Kit Installation
2-25 Weight Kit Installation The collection system requires that a weight kit is After the weight brackets have been secured to the installed to the front of the mower to counter-balance the caster supports, place (1) weight bar P#(B0035) onto the weight of the collection system, when filled with debris. -
Page 19: Throttle Cable Installation
2-26 Throttle Cable Installation NOTE: Engine Driven Models Only Figure 2-26c To install the throttle cable kit to the ROPS (roll over protection system), place the 3/8” U-Bolt P#(K0136) onto the ROPS with the threads facing the front of the mower. -
Page 20: Exploded Views And Parts List
Exploded Parts View A0623 PTO Assembly ISO VIEW M0241 A50K BELT (INCLUDED IN H.W. BAG) - Page 21 PTO Parts List A0623 PTO Assembly Item Document Title Quantity Number Number A0429 GEAR BOX ASSEMBLY K0348 3/8"-16 x 2" ALL THREAD HHCS K0047 3/8" FLAT WASHER 1.00 OD x .446 ID x .075 T K0353 1/4"-20 x 1/2" HHSTS K1159 5/16"-18 x 2"...
-
Page 25: Operating Instructions
3-3 Disengagement Of The Blower SECTION III PTO MODELS OPERATING INSTRUCTIONS A. To disengage the blower, rotate the engagement handle towards the mower. 3-1 General Safety WARNING: The blower will continue to spin. DO NOT Only qualified people familiar with this operator’s manual TOUCH the blower, pulleys, or the belt until the tractor is and the mower’s operator’s manual should operate this turned off. -
Page 26: Lubrication
5-1 Parts And Service Information container, underneath the belt shields, and safety decals. Replace any missing or illegible decals. PECO collection system owners should record the name 2. Inspect the unit for worn or damaged components. and telephone number of their Service Center. Your Repair or replace before the next use. -
Page 27: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. # R2008 # R2007 Part #: R1057... - Page 29 NOTES...
- Page 30 P P P PECO PECO PECO PECO PECO 100 AIRPORT ROAD ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...