Table of Contents
Advertisement
4. You must use an R/C radio system that is in good condition
and a correctly sized motor and components as specifi ed in
this instruction manual.
5. You must correctly install all R/C and other components
so that the model operates correctly on the ground and in
the air.
6. You must check the operation of the model before every
fl ight to ensure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not fl own
this type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for
your fi rst fl ights. If you're not a member of a club, your local
hobby shop has information about clubs in your area whose
membership includes experienced pilots.
8. WARNING: The cowl and wheel pants included in this kit
are made of fi berglass, the fi bers of which may cause eye,
skin and respiratory tract irritation. Never blow into a part
(wheel pant, cowl) to remove fi berglass dust, as the dust
will blow back into your eyes. Always wear safety goggles, a
particle mask and rubber gloves when grinding, drilling and
sanding fi berglass parts. Vacuum the parts and the work
area thoroughly after working with fi berglass parts.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and fl yability of your fi nished model depends
on how you build it; therefore, we cannot in any way
guarantee the performance of your completed model,
and no representations are expressed or implied as to
the performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
DECISIONS YOU MUST MAKE
This is a partial list of items required to fi nish the "Eagle
580 EP" that may require planning or decision making before
starting to build.
Radio Equipment
A 4-channel radio system with four micro servos and micro
receiver are required for this plane. The servos and receiver
shown in the manual are Futaba
Servos and the Futaba 607FS FASST
lower priced alternative would be the Futaba 3115 Micro
Precision Servo.
TRANSMITTER:
❏
4-channel radio (minimum) OR
❏
5-channel computer radio with mixing capabilities
(for fl aperons).
®
S3150 Slim Digital
™
2.4 GHz receiver. A
3
RECEIVER:
❏
4- to 6-channel R146iP PCM receiver, [FUTL0601]; Futaba
FM Single Conversion Short Crystal [Low Band (11-35) –
FUTL62**, High Band (36-60) – FUTL63**]
❏
7-channel Futaba 607 FS FASST 2.4 GHz receiver
(FUTL7637)
SERVOS:
❏
(4) Futaba S3115 Micro Precision Servos [FUTM0415]
[38.9 oz-in (2.8 kg-cm) of torque] OR
❏
(4) Futaba S3150 Slim Digital Servos [FUTM0303] [51.4
oz-in (3.7 kg-cm) of torque]
❏
For 3D rudder throws a 2" [50.8mm] double-sided servo
arm may be required (GPMA1155)
CONNECTORS:
❏
(1) "Y" harness [FUTM4135]
❏
(1) 24" extensions [HCAM2721]
❏
(2) 12" extensions [HCAM2711]
❏
(1) 6" extension [HCAM2701]
The Eagle 580 EP ARF comes with a mounting box for
the Great Planes RimFire brushless out-runner motor. The
RimFire .32 (42-50-800kV) Brushless Out-runner Motor
(GPMG4700) motor has been tested with this plane and
works well.
Electronic Speed Control (ESC)
A brushless ESC (electronic speed control) is required for the
recommended motor set-up. We recommend using the Great
Planes Silver Series SS-45A Brushless ESC [GPMM1840].
If you will be using the 4S LiPo set-up for 3D fl ying, a voltage
regulator must be used with this ESC (we recommend the
Great Planes 3A BEC, GPMM1920). If a voltage regulator is
not used the ESC may be damaged.
Flight Battery
We recommend two different battery and prop set-ups
depending on the type of fl ying you prefer to do. For basic
sport fl ying we recommend the Great Planes Power Series
LiPo 2100mAh 11.1V, 3200mAh 11.1V battery or Flight
Power 2170mAh 11.1V and the 2500mAh 11.1V with an
APC 13 x 8E propeller.
For all out 3D type fl ying we recommend the Great Planes
Power Series LiPo 2100mAh 14.8V or Flight Power 2170mAh
14.8V battery with an APC 12 x 6E propeller. A voltage
regulator will also be required to power the receiver. Be sure to
follow the ESC instructions for using a separate power source
(voltage regulator or receiver battery) for the receiver.
When charging the batteries we highly recommend using a
™
Great Planes Equinox
LiPo Balancer (GPMM3160).
Motor
™
Advertisement
Table of Contents
