Security Tronix ST-PTZ550-27 Installation Manual

High-speed intelligent dome ptz color camera

Advertisement

Quick Links

INSTALLATION MANUAL
©
ST-PTZ550-27
High-Speed Intelligent Dome
PTZ Color Camera
Copyright North American Cable Equipment, Inc.
V2.0 06/13/13
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST-PTZ550-27 and is the answer not in the manual?

Questions and answers

Summary of Contents for Security Tronix ST-PTZ550-27

  • Page 1 INSTALLATION MANUAL © ST-PTZ550-27 High-Speed Intelligent Dome PTZ Color Camera Copyright North American Cable Equipment, Inc. V2.0 06/13/13...
  • Page 2: Package Contents

    One installation manual. PRODUCT DESCRIPTION The ST-PTZ550-27 is a professional grade intelligent dome color camera with pan, tilt and zoom (PTZ) capability of 550TVL (color) and 680TVL (black & white) of resolution. The camera’s design allows the saving of all settings in non-volatile memory. Its 128 preset positions and 8 privacy zones provides versatility for cruise routes and auto tracking functions.
  • Page 3: Unpacking And Handling

    25. Intelligent Power Off 26. Home Position 27. Camera Menu Operation 28. IP66 for Outdoor Use 95% 29. Operating Humidity 30. Heater Operation 42ºF on; 57ºF off 31. Operating Temperature -40ºF - 122ºF 32. Video Connection BNC coaxial 33. Power 24VAC @3A, 35W 34.
  • Page 4: Camera Setup

    The installation site and material must fully support the weight of the product. g. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe gently with a mild detergent. Never use strong or abrasive detergents. h.
  • Page 5: Wiring Connections

    To select the baud rate set switches 3 and 2 on the System Setup DIP Switch as described above. Camera Module Selection The ST-PTZ550-27 uses the Samsung SDM-270 camera module although various other camera modules may be compatible with the unit. The DIP switch settings on the camera module’s PCB board are factory...
  • Page 6: Functions And Operation

    6. FUNCTIONS and OPERATION Basic Operation After powering up the ST-PTZ550-27’s version number, High Speed Dome communication protocol, baud rate and address will be Ver:2.20 shown on the monitor. At the same time, the system will PELCO D/P check the pan and tilt status and display the results. The BPS:2400...
  • Page 7 programming menu. Press [FAR] to increase horizontal zones. Press [NEAR] to reduce horizontal zones. Privacy Zone Press [TELE] to increase vertical zones. Press [WIDE] to reduce vertical zones. Menu Operation Call preset 95 to enter the menu setup. The main menu will be shown on the screen. Note the following symbols: ...
  • Page 8 Exp Mode AUTO Exp Mode Auto (0 – 19) Shutter speed Shutter Speed (0 – 17) Iris Iris (0 – 15) Gain Gain (0 – 18) Bright Bright Backlight (ON/OFF) BackLight Backlight Val BackLight Val Slow Shutter (ON/OFF) Slow Shutter To change exposure mode under ...
  • Page 9 WB mode Auto White Balance Auto R Gain (0 – 255) R Gain (0 – 255) B Gain B Gain For WB Mode Setup – Under  ”WB mode” press OPEN to activate the WB mode menu after “WB mode”. Move the joystick up or down to change the setup. which the menu turns to The order of parameters on the right will be Auto, Manual, Outdoor, Indoor, ATW and OPW.
  • Page 10: Day Night

    To cancel privacy zones – There are two options: (a) restart the camera or (b) decide which privacy zone(s) is to be cancelled. Then enter the relative privacy zone menu, press OPEN to enter the menu, the press CLOSE to cancel the relative privacy zone when the above menu appears.
  • Page 11 NORMAL – call preset 100 DAY – call preset 101 NIGHT – call preset 102. NORMAL is the default mode. Zoom Speed Under the Exposure sub-menu move the cursor to “Zoom Speed” and press OPEN and change the parameters after the  symbol turns to .
  • Page 12 The Shortcut Key Menu is found under the Main Menu. Shortcut keys allow the association of a certain function with a corresponding preset allowing for quick and convenient function selection. Open Menu Open Menu Opens the menu Auto Flip Auto Flip Auto Flip Reference Reference...
  • Page 13 If the Leisure Time reached the previous set value after manual operation the unit will automatically run according to Self Act (except when Self Act is set to “Noting”). If the parameter in Self Act is “Home Place” the user must ensure that “Home Place” is on. The value of Leisure Time can be set from 1 to 240.
  • Page 14: Troubleshooting

    parameters can now be changed. Press OPEN to confirm or CLOSE to cancel. The symbol will return to . Degree The Degree Menu is found under the Main Menu and is used to display the pan degree on the monitor. Move the cursor to Degree and press OPEN. The  symbol turns to .
  • Page 15 CAM ID ∶ ∶ ∶ ∶ ∶ ∶ V2.0 06/13/13...

Table of Contents