Arming In Stay Mode 1; Arming In Stay Mode 2; Table 3: Table; How To Arm The System In Away - Bosch CC484 Operator's Manual

CC484/CC486/CC488 | Operators Manual | 3.
Table 9:

How to Arm the System in AWAY

Mode

Enter your user code followed by
Method
the [#] button (for example,
One
[2580#]).
Two beeps sound and the AWAY
indicator displays. Exit time starts
counting.
Method Hold down the [#] button until two
Two beeps sound.
The AWAY indicator displays and
exit time starts counting.
3.10.3

Arming in STAY Mode 1

STAY Mode 1 is only used when the perimeter
and unused areas of the premises need to be
armed to detect an intruder from entering the
premises. At the same time, you can move freely
within an area that is automatically isolated.
Only your security company can program zones
automatically isolated in STAY Mode 1.
There are two different methods for arming the
system in STAY Mode 1. Method one is standard
and always operates. Method two is optional and
may be disabled by your installer if you do not
want to use single button arming.
Entry Guard Timer for STAY Mode 1
When arming the system in STAY Mode 1, an
optional entry timer called Entry Guard Timer for
STAY Mode 1 is available. Use this entry timer to
delay the sirens if a zone is not automatically
isolated and triggered an alarm condition. Entry
Guard Timer For STAY Mode 1 is the delay time
used for all zones except 24-hour zones when the
system is armed in STAY Mode 1 or STAY Mode
2.
If the Entry Guard Timer for STAY Mode 1 is
programmed and a zone was not automatically
isolated is triggered, the codepad beeps twice a
second until the entry timer expires or the system
is disarmed. If the alarm condition is not reset by
entering your user code followed by the [#] button
(such as, [2580#]) before the entry timer expires,
the sirens activate into alarm. Only your installer
can program this feature.
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Codepad Indicators
Table 10: How to Arm the System in STAY
Mode 1
Method One Enter your user code followed by the [*]
button (for example, [2580*]).
Two beeps sound and the STAY
indicator displays. Exit time starts
counting.
Any zones programmed to be
automatically isolated in STAY Mode 1
flash until exit time expires. At the end of
exit time, all zones selected to be
automatically isolated turn off and the
codepad gives one short beep.
Hold down the [*] button until two beeps
Method Two
sound.
The STAY indicator displays and exit
time starts counting.
Any zones programmed to be
automatically isolated in STAY Mode 1
flash until exit time expires. At the end of
exit time, the zone indicators turn off and
the codepad gives one short beep.
3.10.4

Arming in STAY Mode 2

STAY Mode 2 is only used when the perimeter
and unused areas of the premise need to be armed
to detect an intruder from entering the premise. At
the same time, allowing you to move freely within
an area that is automatically isolated. Any Master
Code user can program zones to be automatically
isolated in STAY Mode 2.
Entry Guard Timer for STAY Mode 2
When arming the system in STAY Mode 2, an
optional entry timer called Entry Guard Timer for
STAY Mode 2 is available. Use this entry timer to
delay the sirens if a zone is not automatically
isolated and triggered into alarm condition. Entry
Guard Timer for STAY Mode 2 is the delay time
used for all zones except 24-hour zones when the
system is armed in STAY Mode 1 or STAY Mode
2.
If the Entry Guard Timer for STAY Mode 2 is
programmed and a zone that was not
automatically isolated triggers, the codepad beeps
twice a second until the entry timer expires or the
system is disarmed. If the alarm condition is not
reset by entering your user code followed by the
[#] button (for example, [2580#]) before the entry
timer expires, the sirens activate into alarm. Only
your installer can program this option.
EN | 8