Codepad Tamper Alarm (Access Denied); Isolating Zones; Standard Isolating; Code To Isolate - Bosch CC484 Operator's Manual

CC484/CC486/CC488 | Operators Manual | 8.
7.5 Codepad Tamper Alarm (Access
Denied)
Codepad tamper restricts the number of times an
invalid user code can be used in an attempt to
operate the system. When the number of incorrect
code attempts equals the number programmed by
your installer, the system activates an alarm
condition. If reporting back to a security
monitoring station, the system sends an Access
Denied report.
To shutdown and lockout a codepad for a period
of time (0 seconds to 150 seconds), ask your
installer to program this function.
8.

Isolating Zones

Use isolating zones to manually disable one or
more zones before arming the system. Once a
zone is isolated, you can access that zone during
the armed state without activating an alarm.
For example, you need to isolate a zone because
before arming the system a PIR detector may be
false alarming, or you need to leave a pet inside a
particular zone while away.
Isolating zones is performed by one of two
methods. Method two is optional and only allows
those user codes programmed by your installer to
have access to isolate zones.
8.1

Standard Isolating

Standard isolating allows all operators to isolate
zones without knowing a valid user code.
How to Isolate a Zone
1. Press the [*] button twice to enter the Isolating
Mode.
Three beeps are heard and the STAY
indicator flashes.
2. Enter the zone number (1 to 8), followed by
the [*] button (for example, [1*] = Zone 1, [2*]
= Zone 2).
Each zone to be isolated has a corresponding
zone indicator that flashes. If you selected an
incorrect zone to be isolated, enter the
incorrect zone number again followed by the
[*] button.
Repeat Step 2 if more than one zone is to be
isolated until all zones to be isolated are
selected.
3. Press the [#] button after all selected zones are
isolated.
Two beeps are heard and the system returns
to the disarmed state.
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Isolating Zones
8.2

Code to Isolate

This method restricts only those User Codes with
the Code to Isolate priority level to isolate zones.
If any User Code has this priority level, the
method of standard isolating does not function.
How to Isolate a Zone
1. Press the [*] button followed by your User
Code and the [*] button again to enter the
Isolating Mode (for example, [*2580*]). Three
beeps sound and the STAY indicator flashes.
2. Enter the zone number (1 to 8), followed by
the [*] button (for example, [1*] = Zone 1, [2*]
= Zone 2).
Each zone to be isolated has a corresponding
zone indicator that flashes. If you selected an
incorrect zone to be isolated, enter the
incorrect zone number again followed by the
[*] button.
Repeat Step 2 if more than one zone is to be
isolated until all zones to be isolated are
selected.
3. Press the [#] button after all selected zones are
isolated.
Two beeps sound and the system returns to
the disarmed state.
9.

Fault Analysis Mode

If a fault occurs, the FAULT or MAINS indicators
flash and the codepad beeps once every minute.
If the AC mains supply fails, the MAINS indicator
flashes until the AC mains supply is restored.
Pressing the [#] button once acknowledges the
fault and stops the codepad from beeping once
every minute.
How to Determine the Type of System Fault
To determine which system fault occurred, enter
Fault Analysis Mode by following the steps below:
1. Hold down the [5] key until two beeps sound.
The FAULT indicator remains steady and the
STAY and AWAY indicators flash in unison.
A zone indicator displays the type of fault that
occurred (for example, Zone 1 = System
Fault). See Table 11 for the list of possible
system faults.
2. To further determine the type of fault
condition, press and hold down the key that
corresponds to the zone indicator displayed.
For example, if Zone 1 displayed System
Fault, press and hold the [1] key to display
which system fault occurred.
3. To exit Fault Analysis Mode and return to the
disarmed state, press the [#] key. The FAULT
indicator continues to display and the codepad
stops sounding once a minute.
EN | 11