Table of Contents
Advertisement
CC484/CC486/CC488 | Operators Manual | 15.
2. Activate all zones requiring the test.
3. When you finish testing all required zones,
press the [#] key to exit this mode. Two beeps
sound, and the STAY and AWAY indicators
turn off. The system returns to the disarmed
state.
14.5
Test Report
This feature only applies if your system reports
using the telephone. By holding down the [9] key
until two beeps sound, the system sends a Test
Report.
15. Event Memory
Use this function to replay the last 40 events that
the system recorded. The event memory history
replays all alarms and the arming/disarming of the
system in AWAY Mode, STAY Mode 1, and
STAY Mode 2. However, the system cannot
differentiate between arming the system in STAY
Mode 1 or STAY Mode 2.
How to Enter Event Memory
Enter your four-character Master Code, followed
by [8] and the [#] button (for example, [25808#]).
Three beeps sound. The last 40 events display one
at a time by the codepad indicators, starting with
the most recent event. A beep sounds as each
event displays.
16. Day Alarm
Day alarm monitors a combination of zones
during the disarmed state. It beeps the codepad
buzzer if activated. Only your installer can
program zones 1 to 4 to operate for day alarm.
Example
A day alarm can be configured for the front door
of a shop with a pressure mat or electronic beam
that customers activate as they enter the shop.
When customers step on the pressure mat or
break the electronic beam, the codepad buzzer
beeps.
How to Turn Day Alarm On
Hold down the [4] key until three beeps sound.
Day alarm turns on. All zones programmed for
day alarm operation cause the codepad buzzer to
beep during the disarmed state when activated.
How to Turn Day Alarm Off
Hold down the [4] key until two beeps sound.
Day alarm turns off.
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Event Memory
17.
Codepad Buzzer Tone
Change
Hold down the [8] key to continuously change the
tone of the codepad buzzer. There are 50 different
tones, from 1500 Hz to 5000 Hz. If multiple
codepads are installed, each codepad can have a
different tone.
18. Remote Arming by
Telephone
Arm your system from any remote location using
the telephone. For security reasons, the system
cannot be disarmed using this method. This
feature requires a touch-tone telephone. Your
installer must program this feature to operate.
How to Remotely Arm Your System by
Telephone
1. Call the telephone number connected to your
control panel.
2. When the control panel answers the incoming
call, a short jingle sounds. To arm the system,
press the [*] key on the touch-tone telephone
for 1 second to 3 seconds.
If you hear modem tones when the control
panel answers the incoming call, the system
was programmed for remote programming
functions by your installer. Wait for a pause
between the tones before pressing the [*] key.
After releasing the [*] key on the touch-tone
telephone, two beeps sound, indicating that
the system is armed in AWAY Mode.
3. Hang up the telephone and the system
remains armed.
If your installer programmed answering
machine bypass, call the control panel
twice to make a connection with the
system. For example, call the telephone
number your control panel is
connected to and let the call ring no
more than four times. Hang up the
telephone. Wait a minimum of 8
seconds before you calling the control
panel again.
19. Partitioning
This feature only applies to the Solution Ultima
880 Control Panels. Your control panel can be
partitioned into four individual areas. Each area
can be operated from one Master Partitioned
codepad, or from separate Area Addressable
codepads.
EN | 15
Hide quick links:
Advertisement
Table of Contents
