Sony PDW-75MD Instructions For Use Manual page 18

p Clip number
This displays the clip number of the clip being monitored.
The clip number in the figure indicates that the first clip
out of 34 clips is selected.
q System frequency
This displays the system frequency being used by this unit
(60I, 50I, 30P, or 25P) (see page 26).
r Audio monitor channels
This displays the audio monitor channels, as set with
MONI CH and MONI SEL on page P1 of the function
menu (see page 73).
When you are monitoring channels 1 and 2 (MONI CH is
set to "CH 1/2"), the display changes as follows,
depending on the setting of MONI SEL.
MONI SEL setting
MONO L (monaural L)
MONO R (monaural R)
STEREO
MIX
2 Audio level adjustment section
1 CH 1 to CH 4 knobs
CH 1 CH 2 CH 3
a CH 1 to CH 4 (audio level) knobs
Depending on the setting of the VARIABLE switch, these
adjust the input audio or playback audio levels of CH 1 to
CH 4.
b VARIABLE (audio level adjustment selector)
switch
This selects whether the input audio or the playback audio
has the levels adjusted by the CH 1 to CH 4 knobs.
REC: Adjust the input audio levels. The playback audio
levels are fixed at their preset values.
PRESET: All of the audio levels are fixed at preset values.
PB: Adjust the playback audio levels. The input audio
levels are fixed at their preset values.
3 Arrow buttons
The four arrow buttons are also used as the MARK1
button, MARK2 button, IN button, and OUT button, as
follows.
M button: MARK1 button
18
Names and Functions of Parts
Display
1 1
2 2
1 / 2
1 + 2
2 VARIABLE switch
CH 4
VARIABLE
REC
PRESET
PB
m button: MARK2 button
< button: IN button
, button: OUT button
You can use these buttons for menu setting operations,
thumbnail selection, setting or deleting In/Out points, and
so on.
1 </IN button and ,/OUT button
MARK1
IN OUT
2 M/MARK1 button and m/MARK2 button
MARK2 3 IN indicator and OUT indicator
a </IN button and ,/OUT button
When the setup or disc menu is visible, use these buttons
to change menu settings. When the THUMBNAIL button
is lit, you can use these for thumbnail selection.
An In or Out point is set when you press the SET button
with the </IN or ,/OUT button held down. The In or
Out point setting is deleted when you press the RESET
button with the </IN or ,/OUT button held down.
b M/MARK1 button and m/MARK2 button
When the setup or disc menu is visible, use these buttons
to change menu settings. When the THUMBNAIL button
is lit, you can use these for thumbnail selection.
During recording and playback, the M/MARK1 or m/
MARK2 button can be pressed with the SET button held
down to record a SHOT MARK1 or SHOT MARK2 as an
essence mark.
To delete or change essence marks, use the supplied PDZ-
1 Proxy Browsing Software. See "Using PDZ-1 Proxy
Browsing Software" in Chapter 4 (page 66) for more
information about installing the PDZ-1 software. See the
online help of PDZ-1 for more information about using
PDZ-1.
You can delete SHOT MARK1 and SHOT MARK2 in the
CHAPTER screen. For details, see "To delete shot marks
at chapter positions" (page 45).
c IN indicator and OUT indicator
IN indicator: This lights when an In point exists. It flashes
if an attempt is made to set an In point after a recorded
Out point.
OUT indicator: This lights when an Out point exists. It
flashes if an attempt is made to set an Out point before
a recorded In point.