Display Diagnostic Codes; Cycle Count Since A Diagnostic Code Occured/Clearing Diagnostic Codes - Maytag MAH9700AW* Service Manual

Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing
requires power.
Selection
Rotary cycle
selector set to
Quick Wash. Press
Rotary Selector
Knob.
Press Delay switch
pad
Press Chime
switch pad
Press Temperature
switch pad
Rotary cycle
selector set to
Colors. Press
Rotary Selector
Knob.
Press Rinse & Spin
switch pad

Display Diagnostic Codes

The diagnostic code display can be
toggled on and off from Service
Mode by pressing the Rinse&Spin
key and rotating the cycle select knob. The display will
show a "d". Rotating the Cycle Selector knob in either
direction will cycle through the list of codes one code
at a time with no wrap. Once an initial direction is
selected by the user (either Clockwise or
Counterclockwise), subsequent movements of the
knob in the same direction will show older codes. If
the user changes direction and turns the knob in the
opposite direction, the more recent code will be
displayed. If rotation is continued to the limits of the
list, the display will remain at the top or the end of the
list. A pair of dashes "- -" will be displayed at the end
of the list of codes, when the control reaches the top,
it will again show "d". A code generated during the
current cycle will be displayed with the Spin Indicator
LED turned "ON". If no cycle is currently running, a
code generated during the previous cycle will be
displayed with the Spin Indicator LED turned "ON".
Access Other Features While a diagnostic code is
displayed, if the Rotary Selector is pressed and held,
the machine will display the number of cycles since
the diagnostic code occurred. To clear the diagnostic
list press the Delay and Chime keys for 3 seconds
while viewing the list.
18
!
Component Function
st
1 press
Drain Pump
nd
Drain Pump on. 2 press
Drain Pump
off.
st
1 press
Motor on. 2
Motor
press Motor
off.
1 Attempt to
Door Lock
unlock
Lock Door
Door Lock
st
1 press
Bleach Valve Fabric
and Cold Softener fill.
nd
Water Valve 2 press
valves off
st
1 press
heater on. 2
Heater
press heater
off.
WARNING
A code generated during the current cycle will be
displayed with the Spin Indicator LED turned "ON". If
no cycle is currently running, a code generated during
the previous cycle will be displayed with the Spin
Indicator LED turned "ON".
Cycle Count Since A Diagnostic Code
nd
Occured/Clearing Diagnostic Codes
While a diagnostic code is displayed, if the Rotary
Selector is pressed and held, the machine will display
the number of cycles since the diagnostic code
occurred. To clear the diagnostic list press the Delay
and Chime keys for 3 seconds while viewing the list.
Diagnostic Codes
Diag. Description
Code
nd
1 No Drain
The door
fails to
2
unlock
3 No Fill
The door
4 fails to lock
5-7
16025909 Rev. 0
Trigger Action to be
taken
The water
level fails to
Displays "nd"
drop below
the Low Go to "Will Not
Water level
Drain"
reset within
Troubleshooting
15 minutes,
Section
before a spin
begins.
Door failed to Displays "LO" Go to
unlock after
"Will Not Unlock"
3attempts Troubleshooting
Section
Continuous fill
Displays "nF"
of 12
Go to "No Water
minutes.
Fill"
Total fill of
Troubleshooting
14minutes.
Section
Door failed to Displays "FL" Go to
lock after 3
"Will not lock"
attempts Troubleshooting
Section.
Not Used
©2005 Maytag Services