Display Diagnostic Codes; Diagnostic Codes - Maytag MAH6700AW Series Service

Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing
requires power.

Display Diagnostic Codes

The diagnostic code display can be toggled 'ON' and
'OFF' from Service Mode by pressing the Rinse &
Spin key and rotating the Rotary Cycle Selector knob.
The display will show a "d".
Rotating the Rotary Cycle Selector knob in either
direction will cycle through the list of codes one code at
a tim e with no wrap. Once an initial direction is selected
by the user (either Clockwise or Counterclockwise),
subsequent m ovem ents of the knob in the same
direction will show older codes. If the user changes
direction and turns the Rotary Cycle Selector knob in
the opposite direction, the m ore recent code will be
displayed. If rotation is continued to the limits of the list,
the display will rem ain at the top or the end of the list. A
pair of dashes "- -" will be displayed at the end of the list
of codes, when the control reaches the top, it will again
show "d".
A code generated during the current cycle will be
displayed with the Spin Speed LED turned 'ON'. If no
cycle is currently running, a code generated during the
previous cycle will be displayed with the Spin Speed
LED turned 'ON'.
Access Other Features
W hile a diagnostic code is displayed, if the Rotary
Cycle Selector knob is pressed and held, the machine
will display the num ber of cycles since the diagnostic
code occurred.
Clear Diagnostic Codes
To clear the diagnostic codes list, press the Delay Start
and Chime keys for 3 seconds while viewing the list.

Diagnostic Codes

Diag. Description
Code
The water level
fails to drop
below the Low
1 No Drain W ater level
reset within 15
m inutes, before
a spin begins.
The door Door failed to
fails to unlock after 3
2
unlock
Continuous fill
of 12 m inutes.
3 No Fill
Total fill of 14
©2006 Maytag Services
!
Trigger Action to be
taken
Displays "nd".
See Will Not
Drain
"Troubleshooting
Procedures"
Displays "LO".
See Will Not
Unlock
attempts
"Troubleshooting
Procedures"
Displays "nF".
See No Water
Fill
"Troubleshooting
m inutes.
Procedures"
WARNING
Diag. Description
Code
The door/lid
4 fails to lock
5-7
W ater level
8
sensor fault.
9
Unbalance
or cabinet
hit detected
during final
spin, which
10
prevented
the spinner
from
exceeding
400 rpm
W ater
E sensor level
fault.
W ill not
rem ember
11
m achine
settings
12-14
16026186
Trigger Action to be
taken
Displays
Door failed to
"FL".See Will
lock after 3
Not Lock
attem pts
"Troubleshooting
Procedures".
Not Used
Input signal
from water level Displays "LE".
sensor is out of
See No Water
range, W asher
Fill
will beep and
"Troubleshooting
pause the wash
Procedures".
cycle.
Not Used
W ill display "dc"
Never
exceeded
See Wet
400rpm due to
Clothes
an unbalance
"Troubleshooting
load.
Procedures "
W ater level in
the m achine is
believed to be
above the
First check to
overflow level.
see that water
W hen this
valve is not
condition is
stuck. If water
detected, the
valve is OK,
machine will
check water level
autom atically
sensor
begin pumping
water out until it
falls below the
overflow level.
See Clear
Diagnostic
Codes.
Disconnect and
reconnect the
Difficulty in
washer power
reading
cord at power
m emory
supply outlet.
If condition still
exists, replace
machine control
board.
Not Used
17