Maytag MAH9700AW* Service Manual page 17

Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing
requires power.
•
Selector" button is pressed, the Main relay
will be toggled (either from "on" to "off" or
from" off" to "on").
•
When the "Rotary Cycle Selector" is set to
"Normal" and the "Rotary Cycle Selector"
button is pressed, the hot water valve will be
turned on. This output will remain on until the
"Rotary Cycle Selector" button is pressed
again to turn off the output. The control will
not allow the machine to fill past the High
water level.
•
When the "Rotary Cycle Selector" is set to
"Wrinkle Control" and the "Rotary Cycle
Selector" button is pressed, the cold water
valve will be turned on. This output will remain
on until the "Rotary Cycle Selector" button is
pressed again to turn off the output. The
control will not allow the machine to fill past
the High water level.
•
When the "Rotary Cycle Selector" is set to
"Delicates" and the "Rotary Cycle Selector"
button is pressed, the bleach valve will be
turned on. This output will remain on until the
"Rotary Cycle Selector" button is pressed
again to turn off the output. The control will
not allow the machine to fill past the High
water level.
•
When the "Rotary Cycle Selector" is set to
"Hand Wash" and the "Rotary Cycle
Selector" button is pressed, the pre wash
valve will be turned on. This output will remain
on until the "Rotary Cycle Selector" button is
pressed again to turn off the output. The
control will not allow the machine to fill past
the High water level.
•
When the "Rotary Cycle Selector" is set to
"Quick Wash" and the "Rotary Cycle
Selector" button is pressed, the drain pump
will be turned on. This output will remain on
until the "Rotary Cycle Selector" button is
pressed again to turn off the output.
•
Pressing the "Delay" switch pad will turn on
the motor and the "Delay" LED. This output
and the LED will remain on until the "Delay"
switch pad is pressed again to turn off the
output. When activated, the machine will
tumble for 5 seconds in the CW direction,
pause for 2seconds, tumble in the CCW
direction for 5 seconds, pause for 2 seconds;
repeating this pattern until " Delay" button is
pressed again to turn off the tumbling. Note
that all tumble speeds are assumed to be 45
rpm.
•
Pressing the "Chime" switch pad will unlock
the door and turn on the all the LED's above
©2005 Maytag Services
!
WARNING
•
•
•
Selection
Rotary cycle selector
set to Super Wash.
Press Rotary
Selector Knob.
Rotary cycle selector
set to Normal. Press
Rotary Selector
Knob.
Rotary cycle selector
set to Wrinkle
Control. Press
Rotary Selector
Knob.
Rotary cycle selector
set to Delicates.
Press Rotary
Selector Knob.
Rotary cycle selector
set to Hand Wash.
Press Rotary
Selector Knob.
16025909 Rev. 0
the "Chime" button. This output will attempt to
unlock one time, if safe to do so.
Pressing the "Temperature" switch pad will
lock the door and all the Temperature LED's
will turn ON. Pressing the "Chime" button will
unlock the door and the all the Chime LED's
will turn ON.
When the "Rotary Cycle Selector" is set to
"Colors" and the "Rotary Cycle Selector" is
pressed, the bleach valve and the cold water
valve will be turned on to check the fabric
softener fill. This output will remain on until
the "Rotary Cycle Selector" button is
pressed again to turn off the output. The
control will not allow the machine to fill past
the High water level.
When the "Rinse & Spin" keypad is pressed,
the Heater will be turned on if the water level
is above the Heater Safety Level. If the water
level is below the Heater Safety Level, a
warning beep will be given and the heater will
not be turned on. The Heater output will
remain on until the "Rinse & Spin" keypad is
pressed again to turn off the output.
Component
Main Relay
Hot Water
Valve
Cold Water
Valve
Bleach Valve
Pre Wash
Valve
Function
On to Off or
Off to On
st
1 press valve
nd
on. 2 press
valve off.
st
1 press valve
nd
on. 2 press
valve off.
st
1 press valve
nd
on. 2 press
valve off.
st
1 press valve
nd
on. 2 press
valve off.
17