Maytag W10240878A Use & Care Manual page 7

more (_
time
[ess
time
[]
wrink[e
prevent
options and modifiers p,os,_,o_tOLock;o_o_k ®
controls
Estimated Time Remain[ng
Moisture sensing strips in the dryer measure the amount of moisture
in the clothes. The estimated time display may adjust to show a
more accurate drying time.
WRINKLE PREVENT Feature
When you are unable to remove a load of clothes from the dryer as
soon as it stops, wrinkles can form. The WRINKLE PREVENT feature
periodically tumbles, rearranges, and fluffs the load to help keep
wrinkles from forming.
[] Get up to 60 minutes of heat-flee, periodic tumbling at the end
of a cycle. Press the WRINKLE PREVENT button to turn ON or
OFF at any time before the cycle has ended.
[] The WRINKLE PREVENT feature is preset to "OFF." if selected
for other cycles, the WRINKLE PREVENT feature setting will
remain "ON" the next time that cycle is selected.
Cycle Signal
The Cycle Signal produces an audible sound when the drying cycle
is finished. Press the CYCI_E SIGNAl. button to turn On or Off at any
time before the cycle has ended.
NOTE: When the WRINKI_E PREVENT feature is selected and
the Cycle Signal is on, an audible sound will be emitted every
20 minutes until the clothes are removed, or the WRINKI.E
PREVENT feature is finished.
This feature allows you to lock your settings to avoid unintended
use of the dryer. YOU can also use the I_ock/Unlock Controls
feature to avoid unintended cycle or option changes during dryer
operation.
To enable the Lock/Unlock Controls feature when dryer
is running:
Press and hold the CYCI_E SIGNAl. button for 3 seconds.
The control is locked when a single beep is heard and the
I.ocWUnlock Controls status light is on.
To enable the Lock/Unlock Controls feature when dryer
is OFF:
When the dryer is off, it is not necessary to press the
POWER/CANCEl. button before activating the I.ocWUniock
Controls feature.
To unlock:
Press and hold the CYCI.E SIGNAl. button for 3 seconds to turn this
feature off.
NOTE: When the dryer is running and Lock/Unlock control is on,
the dryer can be stopped by pressing the START/PAUSE button, but
cannot be restarted until the control is unlocked.
YOu can change Auto Cycles, Timed Cycles, and the drying
temperature on Timed Cycles at any time before pressing Start/
Pause.
[] Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changlng Cycles after starting dryer
1. Press the POWER/CANCEl. button. This ends the current cycle
and turns the dryer OFF.
2. Press the POWER/CANCEl. button again to turn on the dryer.
3. Select the desired cycle and options.
4. Press and hold START/PAUSE. The dryer starts at the beginning
of the new cycle.
Changlng settings on Timed Cycles during the cycle
YOU can change the temperature setting at any time during the cycle
by pressing the TEMPERATURES button.
Follow the progress of your dryer with the drying Status indicator
lights.
Wet
The Wet light illuminates at the beginning of an Auto Cycles if a wet
item is detected.
[]
In an Auto Cycle, if a wet item is not detected after
approximately 5 minutes, the dryer goes directly into Coo[
Down and the Coo[ Down and Wrinkle Prevent indicators
illuminate, if selected.
[] In a Timed Dry Cycle, wet items are not detected. The dryer
will continue to run for the length of time selected, and the Wet
light will illuminate. The damp light will not illuminate.
Damp
The Damp light illuminates in an Auto Cycle when the laundry is
approximately 80% dry.
Cool
Down
The Cool Down light illuminates during the cool down part of the
cycle. I.aundry cools for ease in handling.
Done
The Done light illuminates when the drying cycle is finished. This
indicator stays on during Wrinkle Prevent
Wrinkle Prevent
The Wrinkle Prevent light illuminates when this option is selected.
This indicator stays on during the Wrinkle Prevent setting.
Clean Lint Screen
The Clean [.int Screen light is a reminder to check and clean the lint
screen. The Clean I_int Screen light will come on when the machine
is turned on. The light will flash until the cycle is started or the door
is opened, and then the light will turn off.