Table of Contents
Advertisement
5)
Press as to select the item and press asqw to change the setting according to the instructions.
[SSID]
[AUTHENTICATION]
[OPEN]
[SHARED]
[WPA-PSK ]
[WPA2-PSK ]
[WPA-EAP/WPA2-EAP ] Select when the access point authentication method is WPA-EAP/WPA2-EAP.
[WPA-EAP]
[WPA2-EAP]
[ENCRYPTION]
[NONE]
[WEP]
[TKIP]
[AES]
[DEFAULT KEY]
[KEY1] - [KEY4]
[KEY]
[EAP]
[USER NAME]
[PASSWORD]
Note
f If you are unable to connect to the wireless LAN through the access point even after performing the steps in "Projector
settings" (x page 98), contact the manufacturer of the access point (Radio repeater).
f When using EAP, the projector needs to be set according to the setting of the RADIUS server. Check with the network
administrator for the setting of the RADIUS server.
f When using an EAP together with an access point with invalid SSID broadcast, select [WPA-EAP] or [WPA2-EAP] for the
authentication method even if the authentication method of the access point is WPA-EAP / WPA2-EAP.
f If USER1 ~ 3 use, you cannot connect to the access point of stealth SSID configuration, please use it to cancel the stealth
setting. For details, please refer to the Operating Instructions of the access point.
6)
Press as to select [OK], and press the <ENTER> button.
Chapter 4 Settings - [NETWORK/USB] menu
Enter the same character string that is registered in the access point.
Set the user authentication method used by the network to be connected.
Select when the access point authentication method is Open System.
Select when the access point authentication method is Shared Key.
Select when the access point authentication method is WPA-PSK.
Select when the access point authentication method is WPA2-PSK.
Select when the access point authentication method is WPA-EAP.
Select when the access point authentication method is WPA2-EAP.
Select the encryption method to be used for communication between the projector and
the network.
Select when transmit without encryption.
It is selectable only when [AUTHENTICATION] is [OPEN] or [SHARED].
Select when Encryption is WEP.
Select when Encryption is TKIP.
Selectable when [AUTHENTICATION] is either [WPA-PSK], [WPA2-PSK], [WPA-EAP],
[WPA2-EAP].
Select when Encryption is AES.
Selectable when [AUTHENTICATION] is either [WPA-PSK], [WPA2-PSK], [WPA-EAP],
[WPA2-EAP].
Set 1 – 4 numerals for the default key.
It is can be set when [AUTHENTICATION] is [OPEN] or [SHARED] and [ENCRYPTION]
is [WEP].
Set a [WEP] key to the key number selected with [DEFAULT KEY].
It is can be set when [AUTHENTICATION] is [OPEN] or [SHARED] and [DEFAULT KEY]
is [WEP].
Either the 64-bit or 128-bit WEP key can be set. For the 64-bit key, input 5 alphanumerics
(or a 10-digit string for the hexadecimal format) for the 128-bit key, input 13
alphanumerics (or a 26-digit string for the hexadecimal format).
Set a key.
It is can be set when [AUTHENTICATION] is [WPA-PSK] or [WPA2-PSK].
Input either 8 to 63 alphanumerics or a 64 digit string in the hexadecimal format.
Select the EAP setup in the RADIUS server.
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-EAP] or
[WPA2-EAP].
The types of EAP that can be selected are as follows.
PEAP (MS-CHAPv2), PEAP (GTC), EAP-TTLS (MD5), EAP-TTLS (MS-CHAPv2 ),
EAP-FAST (MS-CHAPv2), EAP-FAST (GTC)
Input a user name used for authentication (excluding spaces) (maximum 64 characters).
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-EAP] or
[WPA2-EAP].
Input a password used for authentication (maximum 64 characters).
It is can be set when [AUTHENTICATION] is [WPA-EAP/WPA2-EAP], [WPA-PSK] or
[WPA2-PSK].
ENGLISH - 91
Advertisement
Table of Contents
