Olivetti d-Copia 3501 Service Manual page 177

SIMULATION 41-3
PD SENSOR DATA DISPLAY.
OCSW
PD1[128]: 200 PD2[128]: 200
PD3[128]: 50 PD4[128]:
PD5[128]: 51 PD6[128]:
PD7[128]: 52
43
43-1
Setting
Purpose
Used to set the fusing temperature in each
Function
operation mode.
(Purpose)
Fixing (Fusing)
Section
Operation
Item
Operation/Procedure
1) Select the number corresponding to the setting mode with 10-
key.
2) Press [START] key.
3) Press [CUSTOM SETTINGS] key.
4) Press [START] key.
Item
1 INSIDE NORMAL Heater inside/normal
2 OUTSIDE NORMAL Heater outside/normal
3 INSIDE PREHEAT Heater inside/preheat
4 OUTSIDE PREHEAT Heater outside/preheat
SIMULATION 43-1
FUSER TEMPERATURE SET. SELECT 1-4, AND PRESS START.
1. INSIDE NORMAL 190
2. OUTSIDE NORMAL 190
3. INSIDE PREHEAT 150
4. OUTSIDE PREHEAT 150
Press [START] key.
SIMULATION 43-1
FUSER TEMPERATURE SET. INPUT VALUE, AND PRESS START.
1. INSIDE NORMAL
44
44-1
Setting
Purpose
Used to set enable/disable of correction
Function
operations in the image forming (process) section.
(Purpose)
Image process (Photoconductor/Developing/
Section
Transfer/Cleaning)
Operation
Item
Operation/Procedure
When bit =1, correction is made.
Bit 15 14 13 12 11 10 9
0 0 0 0 0 0 0
9-34
52
50
Default
190
190
150
150
1
Press [CUSTOM SETTINGS] key.
190
8 7 6 5 4 3 2 1
Vg4 Vg3
Vb1
0 Vb4 Vbr Vb3 Ld2 Vg2 Ld1
Vb2
Ld4 Ld3
SIMULATION 44-1
PROCESS CORRECTION VALUE SETTING. INPUT VALUE 0-255
AND PRESS START.
BIT0:Vg1, BIT1:Ld1, BIT2:Vg2,
BIT4:Vb1, Vb2
BIT5:Vg3, Vb3, Ld3
BIT6:Vbr
BIT7:Vg4, Vb4, Ld4
44-4
Setup
Purpose
Used to set the target image (reference) density
Function
level in the developing bias voltage correction.
(Purpose)
Process
Section
(OPC drum, developing, transfer, cleaning)
Data
Item
Operation/Procedure
1) Select the number corresponding to the setting mode with 10-
key.
2) Press [START] key.
3) Enter the set value.
4) Press [START] key.
1 TEMP. AREA *1
2 HUMIDITY AREA *1
3 S_WT
4 Vb1
5 Vb2
*1: Only when this value is 0, control is made with the actual mea-
surement value of the process thermistor (temperature/humid-
ity). When it is not 0, control is made with the forcible setting
value.
SIMULATION 44-4
PROCESS CONTROL VALUE SETTING. SELECT 1-5 AND PRESS
START.
1.TEMP. AREA
2.HUMIDITY AREA
3.S_WT 100
4.Vb1 50
5.Vb2 50
Press [START] key.
SIMULATION 44-4
PROCESS CONTROL VALUE SETTING. INPUT VALUE, AND PRESS
START.
3.S_WT
0
Vg1
Service Manual
BIT3:Ld2
111
Item
Process environment temperature
forcible setting value
(0 - 13 /normal: 0)
Process environment humidity
forcible setting value
(0 - 14 /normal: 0)
Vb rising correction standby time
(0 - 180 sec/default: 90)
Vb correction amount (first rotation)
(0 - 150V/default: 50)
Vb correction amount (second
rotation) (0-50V/default: 15)
0
0
Press [CUSTOM SETTINGS] key.
101
Y105220-6
3