Olivetti d-Copia 3501 Service Manual page 173

26-41
Setting
Purpose
Used to set the automatic magnification ratio
Function
selection (AMS) in the pamphlet mode.
(Purpose)
Section
Specifications
Item
Operation/Procedure
1) Enter the number corresponding to whether AMS operation is
automatically performed or nor in the center binding mode with
the 10-key.
2) Press [START] key.
0 NO AMS/APS selection allowed
1 YES AMS is forcibly operated.
(Default: 1 for Europe and UK, 0 for the others)
SIMULATION 26-41
PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS
START.
0. NO
1. YES
26-50
Setting
Purpose
Black-White reverse YES/NO setting
Function
(Purpose)
Specifications
Item
Operation/Procedure
1) Select ENABLE/DISABLE of the B/W reverse mode with 10-
key.
2) Press [START] key.
0 DISABLE B/W reverse mode DISABLE
1 ENABLE B/W reverse mode ENABLE
SIMULATION 26-50
B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS
START.
0. DISABLE
1. ENABLE
26-52
Setting
Purpose
Used to set whether non-print paper (insertion
Function
paper, cover paper) (blank image print paper) is
(Purpose)
counted up or not.
Paper transport (Discharge/Switchback/Transport)
Section
Specifications
Item
Operation/Procedure
1) Select YES/NO of the non-print paper count-up with 10-key.
2) Press [START] key.
Non-print paper means an insert paper (without copying) in the
OHP insertion mode, a cover (without copying) in the cover inser-
tion mode, back surface, and white paper in the duplex exit mode
(CA, etc.).
0 NO (NO COUNT UP)
1 YES (COUNT UP)
(Default: 0 for Japan and Australia, 1 for the other)
The target counters are as follows:
• Copies counter
• Printer counter
• Department management counter
• Total counter
9-30
Operation mode (Common)
1
Operation
Default
1
Operation mode
No count up
Count up
Service Manual
• Effective paper counter
SIMULATION 26-52
BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS
START.
0. NO (NO COUNT UP)
1. YES (COUNT UP)
26-68
Setting
Purpose
Used to set ENABLE/DISABLE of the CA key
Function
cancel function of print stop.
(Purpose)
Section
Specifications
Item
Operation/Procedure
1) Select ENABLE/DISABLE of the CA key cancel function of
print stop with 10-key.
2) Press [START] key.
0 DISABLE
1 ENABLE (PRINT STOP)
(Default: 1)
SIMULATION 26-68
CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS
START.
0. DISABLE
1. ENABLE (PRINT STOP)
27
27-1
Setting
Purpose
Used to set the specifications for operations in
Function
case of communication trouble between the host
(Purpose)
computer and MODEM (machine side). (When
communication trouble occurs between the host
computer MODEM and the machine, the self diag
display (U7-00) is printed and setting for inhibition
of print or not is made.)
Communication unit (TEL/LIU/MODEM etc.)
Section
Specifications
Item
Operation/Procedure
1) Select the number corresponding to the operation mode with
10-key.
2) Press [START] key.
0 YES Though a communication trouble occurs between
the host computer and the MODEM (machine side),
there is no effect on the machine operations.
1 NO When a communication trouble occurs between the
host computer and the MODEM (machine side), the
self diag display (U7-00) is displayed and printing is
inhibited.
(Default: 0)
SIMULATION 27-1
DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.
0. YES
1. NO
1
Operation
Disable
Enable
0
Operation mode
1
Y105220-6