Acceptable Originals - Olivetti d-Copia 3501 Service Manual

[10] MACHINE OPERATION

1. Acceptable originals

A stack of up to 50 original sheets (30 original sheets*
14" (B4) or larger) of the same size paper can be set in the docu-
ment feeder tray provided the stack height is within the limit shown
below.
A stack of up to 30 mixed size originals can be set if the width of
the originals is the same and the stack height is within the limit
shown below. In this case, however, stapling and duplex will not
function and some special functions may not give the expected
result.
*1: For paper heavier than 28 lbs. (105g/m
15 sheets can be set. Setting 16 or more sheets may cause
incorrect scanning of original and scanned image may
become expanded compared with original itself.
A. Size and weight of acceptable originals
5-1/2" x 8-1/2"
or A5
Original size:
(148 x 210 mm)
Weight (thickness):
14 lbs. or
2
g/m ... Weight of a sheet of paper of 1 m
B. Total number of originals that can be set in
the document feeder tray
Total aggregate thickness must not exceed 1/4" or
6.5 mm (for 14 to 21 lbs. or 50 to 80 g/m
Total aggregate thickness must not exceed 3/16" or
5.0 mm (for 21 to 34 lbs. or 80 to 128 g/m
<Notes on use of the automatic document feeder>
• Use originals within the specified size and weight ranges. Use of
originals out of the specified range may cause an original mis-
feed.
• Before loading originals into the document feeder tray, be sure
to remove any staples or paper clips.
• If originals have damp spots from correction fluid, ink or glue
from pasteups, be sure they are dried before they are fed. If not,
the interior of the document feeder or the document glass may
be soiled.
• Do not use the following originals. These originals may cause
incorrect original size detection, original misfeeds, and smudges
on copies.
Transparency film, tracing paper, carbon paper, thermal paper
or originals printed with thermal transfer ink ribbon should not be
fed through the document feeder. Originals to be fed through
the feeder should not be damaged, crumpled or folded or have
loosely pasted paper on them or cutouts in them. Originals with
multiple punched holes other than two-hole or three-hole
punched paper may not feed correctly.
Y105220-6
1
for 8-1/2" x
2
), only a stack of up to
11" x 17"
or A3
(297 x 420 mm)
50g/m 2 34 lbs. or 128g/m 2
2
2
paper).
1/4" or 6.5 mm
or less
2 paper).
3/16" or 5.0 mm
or less
• When using originals with two or three holes, place them so that
the punched edge is at a position other than the feed slot.
2. Standard original placement
orientations
Place originals in the document feeder tray or on the document
glass so that the top and bottom of the original is positioned as
shown in the illustration. If not, staples will be incorrectly posi-
tioned and some special features may not give the expected
result.
[Example 1]
Document feeder tray
Top
Bottom
[Example 2]
3. Automatic copy image rotation -
rotation copying
If the orientation of the originals and copy paper are different, the
original image will be automatically rotated 90° and copied. (When
an image is rotated, a message will be displayed.) If a function is
selected that is not suitable for rotation, such as enlarging the
copy to greater than 8-1/2" x 11" (A4) size or staple sorting with
the saddle stitch finisher, rotation will not be possible.
[Example]
Orientation of original
Face down
Sevice Manual
Hole positions
Hole
positions
Hole positions
Document glass
Top
Bottom
Top
Top
Bottom
Bottom
Orientation of paper Copy after rotation
Face down
10-1