Olivetti d-Copia 3501 Service Manual page 151

SIMULATION 2-2
SPF SENSOR CHECK.
SPFSET SOCD
SPPD SPOD
SWD4 SWD3
SPLS2 SPLS1
SWD_LEN: 2100
2-3
Operation test/Check
Purpose
Used to check the operations of the loads in the
Function
automatic document feeder unit and the control
(Purpose)
circuits.
DSPF
Section
Operation
Item
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
1 MOTOR(H) Motor high speed
2 MOTOR(L) Motor low speed
3 SDSS SPF gate solenoid
4 SPFS SPF pick-up solenoid
5 SPFC SPF paper feed clutch
6 SRRC
SPF resist roller clutch
7 STMPS Stamp solenoid
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-7, AND PRESS START.
1.MOTOR(H) 2.MOTOR(L)
3.SDSS 4.SPFS 5.SPFC
7.STMPS
Press [START] key, and the
operation is started.
SIMULATION 2-3
SPF LOAD TEST. EXECUTING···.
1.MOTOR(H) 2.MOTOR(L)
3.SDSS 4.SPFS 5.SPFC
7.STMPS
3
3-2
Operation test/Check
Purpose
Used to check the operation of sensor and
Function
detector in the finisher and the related circuit.
(Purpose)
Finisher
Section
Operation
Item
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
9-8
SCOV SPED
SWD6 SWD5
SWD2 SWD1
CISSET STSET
SWD_AD: 600
2
6.SRRC
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
2
6.SRRC
STHP Stapler HP detection
POD Tray 2 paper exit detection
SCID Staple compiler paper entry detection
PID Paper entry detection
T2PD Tray 2 paper empty detection
T2DN Tray 2 lower limit detection
T2UP Tray 2 upper limit detection
JRHP Jogger R HP
JFHP Jogger (F) HP
SCID2 Staple compiler paper entry detection 2
STTHP2 Staple rotation HP detection 2
STTHP1 Staple rotation HP detection 1
STUHP Staple shift HP detection
PSHP Pusher HP detection
PPD Paper hold return detection
DSW2 Staple replacement door open detection
DSW1 Compiler jam cancel door open detection
24VM 24V power supply
T1PF Tray 1 full detection
STSP Stapling ready detection
STLS Cartridge inside spare staple empty detection
STNC Cartridge empty detection
DOPD Interface unit door open detection
MMLK Main drive motor lock detection
SCPD Staple compiler paper empty detection
FSSS Stapler safety switch
FJS Joint switch
FFDSW Front door switch
FTCS Upper cover sensor
FFDS Front door sensor
FSPS Self prime sensor
FSUC Stapler connection detection
FSS Staple sensor
FSTHPS Stapler HP sensor
FSHPS Slide HP sensor
FLE Lift lock sensor
FLLLS Lift lower limit sensor
FULS Lift upper limit sensor
FFE Bookbinding clock sensor
FFES Bookbinding paper sensor
FFRHPS Bookbinding roller HP sensor
FFHPS Bookbinding HP sensor
FFPS Bookbinding position sensor
FSLS Paper surface sensor
FBES Tray paper sensor
FOBHPS Paper exit belt HP sensor
FAS Alignment tray sensor
FRJHPS Alignment HP sensor R
FFJHPS Alignment HP sensor F
FARHPS Bundle roller HP sensor
FPHPS Paddle HP sensor
FES Entry port sensor
• The following units are added when the punch unit is installed to
the console finisher:
FPE
FPSHPS
FPUC
FPDS
FPDSS4
FPDSS3
FPDSS2
FPDSS1
FPTS
Service Manual
Built-in finisher
Console finisher
Punch motor encoder
Punch side register HP
Punch connection detection
Punch dust sensor
Punch side register sensor 4
Punch side register sensor 3
Punch side register sensor 2
Punch side register sensor 1
Punch timing sensor
Y105220-6