Kyocera Mita S-9100DN Operation Manual page 73

Chapter 4 Troubleshooting
Message
Close
front cover
Close left
cover 1 (-3)
Close reverse
adapter
Face-down tray
paper full
Finisher tray 1(2)
paper full
Finisher
path error
Install MK
Load Cassette 1(to4)
(paper size)/(paper type)*
*(paper size) and (paper type)
are displayed flashing
alternately.
Load MP tray
(paper size)/(paper type)
*(paper size) and (paper type)
are displayed flashing
alternately.
Missing
chad box
Missing
toner container
Missing
stapler unit
Missing waste
toner box
Option interface
Error ##
Paper jam
###############
:Alarm buzzer sounds when an error occurs. Press the CANCEL key to stop the alarm buzzer.
4-5
Close the printer front cover.
Close the printer left cover. If left cover of the option paper feeder is open, 2 or 3 is displayed.
Close the reverse adapter cover of the option document finisher.
The face-down tray has become full (approx. 500 pages). You must remove all printed pages from the
face-down tray. When the printer senses that the face-down tray is empty again, it will continue printing
into the face-down tray.
The finisher tray is full. When removing the paper, printing will be resumed, "1" indicates the upper tray,
while "2" indicates the lower tray.
The option document finisher is not installed correctly. Install it correctly.
The maintenance kit (MK-700 for FS-9100DN/MK-701 for FS-9500DN) needs to be replaced.
Replace the maintenance kit since the total number of printed pages has reached 500,000. Call for
service. The maintenance kit includes a drum unit, developer unit and so on.
There is data for printing that matches with a paper cassette setting (paper size, paper type), but there
is no paper in the paper cassette.
Set paper into the paper source as displayed on the operator panel, and press the GO key to restart
printing. However, the paper source numbers (3 to 4) are only displayed when there is an option
paper feeder installed.
Or, if you want to print from a different paper source press the 3 or 4 key to display Use
alternative? and you can change the source for paper feeding.
After selecting a paper source and pressing the MENU key, Paper Handling > appears. By
pressing the 2 key, the paper type settings menu appears. After setting the correct paper type, press
the ENTER key and printing starts.
There is no paper cassette set (paper size, paper type) that matches with the data for printing, so
printing is done from the MP tray. Set paper into the MP tray that matches the paper size and type
shown on the display and press the GO key to restart printing.
Or, if you want to print from a different paper source press the 3 or 4 key to display Use
alternative? and you can change the source for paper feeding.
After selecting a paper source and pressing the MENU key, Paper Handling > appears. By
pressing the 3 key, the paper type settings menu appears. After setting the correct paper type, press
the ENTER key and printing starts.
The punch unit chad box of the DF-70 is not installed correctly. Install it correctly.
Install the toner container. See
The printer does not operate when this message is displayed.
The stapler unit is not installed correctly in the document finisher. Install it correctly.
Install the waste toner box. See
operate when this message is displayed.
A failure has occurred with the option network interface card.
Check the option network interface card installed in the printer.
Open the front cover or left cover and correct the paper jam (or paper mis-feeding in the paper
cassette). The location of the paper jam is also indicated in place of the #'s. Online help messages
which are useful for correcting the paper jam will be displayed by pressing the
a Paper Jam on page 4-8.)
Corrective Action
Toner Container Replacement on page
Toner Container Replacement on page
6-1.
6-1. The printer does not
key. (See Correcting
?
(Continued on next page)