Oven Control Testing Procedures - Jenn-Air JDS8850AAB Service Manual

Testing Procedures
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to oven before servicing,
unless testing requires power and/or gas.
To avoid risk of electrical shock, personal injury or equipment failure, use extreme caution when taking voltage
measurements in the Electronic Control. Failure to do so could short-circuit the control or result in electrical shock.
Illustration
Electronic control

Oven Control Testing Procedures

Changing factory set default options: 1. Press Setup Options and the desired pad simultaneously (see table).
Control Component
EOC II Oven
temperature
adjustment
EOC II End-of-Timer
Reminder beeps
EOC II Control Lock
EOC II Twelve Hour off/
Sabbath mode
EOC II Sound Level
(Beeper Volume)
EOC II 24-Hour Clock
EOC II Scroll Speed
EOC II End-of-Cook-
Time Signal
EOC II Temperature
Display
EOC II Language
Display
EOC II Factory Default
EOC II Clock Display
EOC II Test Access
©2005 Maytag Services
!
!
Component
Door logic sensor ..............................
Meat probe ........................................
Downdraft motor high setting.............
Downdraft motor low setting ..............
2. Press Autoset to change the option.
3. Press any pad except Cancel to accept the change.
4. Press Cancel to cancel the operation.
Test Procedure
Press Bake pad and enter 550° F (288° C).
Press and hold Bake pad until TEMP ADJ
displays. Press Autoset pad to adjust oven in
5° F (-15° C) increments, from -35° F
(-37° C) to 35° F (2° C).
Press Setup Options and the applicable timer
pad ( Timer 1 or Timer 2 ) simultaneously.
Press Setup Options and the Control Lock pad
(also the 1 pad) simultaneously.
Press Setup Options and the 12 Hour Off pad
(also the 2 pad) simultaneously.
Press Setup Options and the Sound Level pad
(also the 3 pad) simultaneously.
Press Setup Options and the 12/24 Hour Clock
pad (also the 4 pad) simultaneously.
Press Setup Options and the Scroll Speed pad
(also the 5 pad) simultaneously.
Press Setup Options and Cook Time Beeps
pads (also the 6 pad) simultaneously.
Press Setup Options and the Temp C/F pad
(also the 7 pad) simultaneously.
Press Setup Options and the Language pad
(also the 8 pad) simultaneously.
Press Setup Options and the Default pad (also
the 9 pad) simultaneously.
Press Setup Options and the Display On/Off
pad (also the Clock pad) simultaneously.
Press and hold Cancel and Broil pads for 3
seconds at power up or within 5 minutes of
power up mode. See "Quick Test Mode."
WARNING
WARNING
Test Procedure
16026016
Results
P11 (Red, pin 5) to P11 (Black,
pin 2):
Door Locked: Continuity
Door Unlocked: Infinity
P2 (Red) to P2 (Red). See "Meat
Probe" chart.
P14 (Tan) to P5 (White): 120 VAC
P22 (Orange) to P5 (White): 120 VAC
Results
While increasing or decreasing oven
temperature, this does not affect self-
cleaning temperature.
Selects the number of beeps emitted
when a timed bake cycle ends.
Press Autoset to select option (enable
disable). The timer, clock and oven light
remain operational.
Disables the normal 12-hour shutoff,
allowing the oven to operate indefinitely.
Press Autoset to select setting (I lowest
through IIIIIIII 8 highest).
Press Autoset to select option (12-hour
time or 24-hour time).
Press Autoset to set speed of displayed
messages (slow, medium, fast).
Press Autoset to set the number of
beeps emitted at the end of a "clock-
controlled" cook cycle.
Press Autoset to select option
(°F or °C).
Press Autoset to select option
(English, French or Spanish).
Press Autoset to reset clock to factory
settings.
Press Autoset to select clock display (on
or off).
Allows access to each function for testing
purposes.
19