Sony SR-R1 Operation Manual page 56

Using the Select FPS function
1
Connect the unit to the PMW-F3.
For details on the connection settings, see
"Connection to the PMW-F3" (page 96) or
refer to the operation manual supplied with the
PMW-F3.
2
Make the system settings.
Select the target frame frequency (24, 25, or
30PsF) and recording format (4:2:2 Lite,
4:2:2 SQ, or 4:4:4 SQ).
Setting example: When setting the target
frame frequency to 24PsF (23.98PsF) and
recording format to 4:4:4 SQ
Display the SYSTEM Setup menu and then
1 select and confirm SYSTEM FORMAT
t2 set the format to match the system
format of the camera as shown below t3
move the cursor to and confirm [SET].
1 SYSTEM FORMAT
S Y S T E M S e t u p
FILE LIST
SYSTEM FORMAT
INGEST
PB FUNCTION
TEST SG
LCD
KEY MAP
KEY INHI
REMOTE/LOCAL
REC INHI
POWER
BATTERY
SRMemory
OTHERS
S T O P
S R - R 1
The formats of the unit and camera are
switched, and "S59P(23PsF)" is displayed on
the display (for about 30 seconds).
SR Motion Recording
dB
SDI SDI SDI SDI SDI
0
-10
SYSTEM : 23.98PsF
-20
SEL-FPS : 59.94P
-30
MODE : ON
-60
SIGNAL : 48 FPS
EMP EMP EMP EMP EMP
EE
L R L R L R L R L R
1 2 3 4 5
STBY OFF
TCG
01 01
H
A001C001_120530RT
16.5V REMAIN
- - -
56
SR Motion
2 Set to match
the camera
System Format
SELECT FPS ON
FPS FORMAT S59/S60
ENCODE SR-SQ
SDI IN 1.5G Dual
SDI OUT 1.5G Single
[SET]
MAP
LCL
OFF
0 0: 00: 00 :0 0
TCR
3 SET
SDI SDI SDI SDI SDI SDI SDI SDI SDI SDI SDI
48
FPS
EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP
[ x 0.500 ]
L R L R L R L R L R L R L R L R L R L R L R
6 7 8 9 10 11 12 13 14 15 16
SR-R1
KEYINHI
51 11 RECINHI
M S F
MK: --:--:--:--
LOCAL
1920x1080
ENCODE
S59P
EE
SR-SQ
(23PsF)
10bit
17:11
4:2:2
"S59P" indicates that SR Motion is enabled
(SELECT FPS is set to "ON") and that the
FPS FORMAT (system frequency during
recording) is set to 59.94P.
The "(23PsF)" indicates that the target frame
frequency is set to 23.98PsF.
To make the time code continuous
Make the following settings in the TC Setup
menu. (see page 34)
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset)
3
Set the number of frames to shoot.
You can also set the number of frames to shoot
from the camera. For details, refer to the
operation manual supplied with the PMW-F3.
If the system is set to Select FPS, the "SR
Motion Recording" window appears in the
audio level meter area, allowing you to
confirm the number of shooting frames.
If you press the HOME button while holding
down the FUNC button, the signal format
display at the bottom of the screen changes to
the SR Motion display, allowing you to
check the setting for the number of frames to
shoot.
SR Motion Recording
dB
SDI SDI SDI SDI SDI
0
-10
SYSTEM : 23.98PsF
-20
SEL-FPS : 59.94P
-30
MODE : ON
-60
SIGNAL : 48 FPS
EMP EMP EMP EMP EMP
EE
L R L R L R L R L R
1 2 3 4 5
OO3O CASS OUT
TCG
00 17
H
A001C001_120530RT
ENCODE
16.5V REMAIN
SR-SQ
- - -
10bit
Playback speed
4
Start shooting.
Use the SYNCHRO REC function, and use
the REC button on the PMW-F3 to start/stop
recording.
For details on the SYNCHRO REC function, see
"Synchronized Recording" (page 96).
SDI SDI SDI SDI SDI SDI SDI
48
FPS
EMP EMP EMP EMP EMP EMP EMP
[ x 0.500 ]
L R L R L R L R L R L R L R
6 7 8 9 10 11 12
SR-R1
KEYINHI
55 16
RECINHI
M S F
MK: --:--:--:--
1920x1080 LOCAL
S59P
EE
(23PsF)
4:2:2 10:11
Number of frames (FPS)