Nikon D300 Repair Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Digital Camera
  5. D300
  6. Repair manual

Nikon D300 Repair Manual

Hide thumbs Also See for D300:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Quick Manual
Printed in Japan NOV.2007
logo Q0310 forGraphic
070509 Gdesign ito
REPAIR MANUAL
作成承認印
VBA20001
Copyright ｃ 2007 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
INC
VBA20001-R.3720.A
配布許可印
サービス
計画課
Ｍ

Advertisement

Table of Contents
loading

Related Manuals for Nikon D300

Summary of Contents for Nikon D300

  • Page 1 VBA20001-R.3720.A 作成承認印 配布許可印 サービス 計画課 Ｍ VBA20001 logo Q0310 forGraphic 070509 Gdesign ito REPAIR MANUAL Copyright ｃ 2007 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !! Printed in Japan NOV.2007...
  • Page 2 When "Separation of Front body from Rear body", "Disassembly of CCD/FPC unit" and "Disassembly of Bayonet" are performed, be sure to carry out "RESET AF-DEFOCUS COMPENSATION" of the D300 adjustment software after assembly. - Ｄ  ･ logo Q0310 forGraphic...
  • Page 3 VBA20001-R.3720.A Disassembly 1. External area and Image-related PCB/base plate External rubber ※ Caution: Take out the screw (#1647) first, and then remove the grip rubber (#B60). ・ Remove the external rubber (#B60, #B61, #B63, and #B447). #B447 #B61 #1647 #B63 #B60 IF lid ・Take out the two screws (#1642).
  • Page 4 VBA20001-R.3720.A Bottom cover / Battery lid unit ・Open the battery lid (#B�01) approx. 4�-degree upwards, #B�01) approx. 4�-degree upwards, upwards, , and remove as if pulling it out. ・Take out the three screws (#1��0), five screws (#1��6), two screws (#1509). Battery cover (#B801) ・Remove the bottom cover.
  • Page 5 VBA20001-R.3720.A Rear cover unit ・Take out the two screws (#1553), two screws (#1547) and one screw (#1551). ・Remove the rear cover slowly, and disconnect the three FPCs from each connector. #1551 #1553×2 #1547×2 2-803 (5) CF cover, sponge, other small parts ・Take out the two screws (#1518).
  • Page 6 VBA20001-R.3720.A TFT monitor and other small parts #431 #433 #434×2 #488 #1057 #435×2 #489 #492 #432 #1629 　#484 #487 #1627×2 #1627 #1546×2 #1626×3 　#486 #491 　#493 #1571 Selector button, Sponge, and other small parts #985 #1538×2 　#467 #468 　#986 #962 #481 　#469 #474...
  • Page 7 VBA20001-R.3720.A I/F cover ・Take out the two screws (#1510) and remove the I/F cover (#B28). ・Remove the conduct plate (#695). #B28 #695 #1510×2 WARNING Take extra care not to get an electric shock when detaching covers. After removing covers, b e sure to discharge the main condenser according to the instructions of repair manuals .
  • Page 8 VBA20001-R.3720.A DG-PCB ・Remove the harnesses (#1075, #1074, and #1073) from each connector. ・Disconnect the FPC (#1027 #1027､#1040､#1041､#1039､#1038) from each connector. ) from each connector. ・Take out the screw (#1546) and remove [#B1017]. #1039 #1074 #1027 #1041 #1038 #1075 #1073 #1040 #1546 #B1017 CF base plate unit...
  • Page 9 VBA20001-R.3720.A Top cover unit Removal of Top cover ・Remove the dioptor-adjustment knob cover plate (#850), and take out the screw (#1622). ・Remove the dioptor-adjustment knob (#852), drip-proof sponge (#857) and drip-proof collar (#851). ・Raise the built-in speedlight, and take out the two screws (#1548), two screws (#1547), three screws (#1555) and two screws (#1511).
  • Page 10 VBA20001-R.3720.A DR base plate and other small parts #690 #1537×2 　#1502 #1014 　#1541×2 　#1502×2 　#811 　#1541 #688 #1541 #439 #691 #769 #B687 　#15337 　#1027 - Ｄ  ･ logo Q0310 forGraphic 070509 Gdesign ito...
  • Page 11 VBA20001-R.3720.A Command dial, Shoe base and other small parts Shoe base #318 ・Take out the four screws (#321). ・Remove the four solders of the shoe base. #316 #948×2 #B317 Solder #701 #702 #920 #972 #708 #321×4 #B726 #517 #1541 #1571×2 #324 #323 #1033...
  • Page 12 VBA20001-R.3720.A Outside LCD, Release SW and other small parts Outside LCDFPC LCDFPC ・Unsolder the three wires . ・Take out the screw (#1606) and remove the spring (#750). ・Take out the two screws (#1547), three screws (#1544), two screws (#1540) and one screw (#1560). ・Remove the power plate (#747), outside LCD frame (#703), #787 Compensation/mode button support plate (#731).
  • Page 13 VBA20001-R.3720.A SB case, Synchro-terminal and other small parts #B302 #301 #305 #303 #796 #1601 #322 #1623×2 #1601 #322 #796 #307 #513 #770×2 #917A ～ C #188 #309 #310 #308 #312 #306 #765×2 #766×2 #1565 - Ｄ  ･ logo Q0310 forGraphic 070509 Gdesign ito...
  • Page 14 VBA20001-R.3720.A Mode dial, Eyelet and other small parts Soldering bridge Solder Mode dial / Trefoil button Trefoil button ・Remove the soldering bridges of the FPC (#1025) and [#1026]. ・Take out the screw (#1574) and remove the mode dial unit (#B504) and the trefoil button unit (#B502).
  • Page 15 VBA20001-R.3720.A Main PCB unit ・Remove the five solders of the Shutter-FPC main PCB (#1001). ・Disconnect the FPCs (#1030, #1009 #1030 #1009, #1005) and the shutter- Main-PCB (#B1001) FPC from each connector. ・Take out the three screws (#1616), and remove the main PCB #1005 (#B1001) and the conduction lug plate (#775).

  • Page 16: Front Body

    VBA20001-R.3720.A 2. Separation of Front body from Rear body #1042 #1047 ・Remove the FPC (#1042) from the connector. ・Take out the six screws (#1�7�), one screw (#1�2�), one screw (#1�72), and two screws (#1531). ・Remove the front body from the rear body. #1526 Dioptor adjustment gear case ・Take out the screw (#1526) and remove the dioptor...
  • Page 17 VBA20001-R.3720.A AE FPC unit ・Disconnect the FPC from the connector. ・Take out the three screws (#1617). ・Remove the AE FPC unit. #1617×3 #883×3 #B1006 #933 #884×3 #B882 Eyepiece block unit ・Peel off the eyepiece lower dustproof tape (#909). ・Take out the two screws (#1619) and remove the eyepiece block unit. #1619×2 #B846 #844...
  • Page 18 VBA20001-R.3720.A P.Box unit #956 #B1005 #1542×2 #1618×2 #955 #871×2 #B1004 #840 #910 #904 #872×2 #891 #837 #874×2 #873×2 #839 #833 #890 #838×2 #1055 #901 #877 #B832 #895A ～ C #876×2 #834 AF FPC unit ・Take out the two screws (#1507). ・Disconnect the FPC of AF FPC unit (#B1007) from the connector.
  • Page 19 VBA20001-R.3720.A PD base plate/10-pin terminal ・Remove the ten solders of the wires that are connected to the PD base plate (#1002). ・Disconnect the FPC (#1010) from the connector. ・Take out the screw (#1522), and remove the PD base plate. ・Remove the solder of the lens release SW lug plate (#680) and also remove nine solders of the 10-pin terminal (#41) (which is assembled from the other side and soldered).
  • Page 20 VBA20001-R.3720.A Front cover, Bayonet and other small parts #1527 #B382 #992 #38×2 #407 #1514 #387 #383 #1514 #406 #402 #401 #1621×4 #906 #1620 - Ｄ  ･ logo Q0310 forGraphic 070509 Gdesign ito...
  • Page 21 VBA20001-R.3720.A Mirror box, I base plate, Release base unit and other small parts #B211 #263 #1523×2 #233 #232 #1525×3 #231 #241 #214 #B10201 #243 #B10212 #242 #1568 #210 #236A ～ E #1523×2 #170 #1516 #B71 #B381 I base plate #1530 #66×3 #377 ・Remove the soldering bridges.
  • Page 22 VBA20001-R.3720.A AF drive section, P/F button, Lens contact, and other small parts Lens contact #261 #1504×2 #B1009 #234 Soldering bridge #1510×4 #1652×2 #35×2 #B1024 #B1008 #608 #1521 #1615 AF drive section #934×2 #1636×2 #B328 #36×2 #343×2 #33×2 #342 #1513 #B10355 - Ｄ...
  • Page 23 VBA20001-R.3720.A 4 ． Rear body Charge-base plate, I/F base plate, Main condenser and other small parts #B1067 #1572 #1573×3 #1638 #1029 #B326 #1564 #614 #B1067 #B602 #606×2 #930 #1029 #1564 #1101 #1102 #710 #399 Brown Yellow DI base plate #1509×2 #1543×2 #B1019 #B812...
  • Page 24 VBA20001-R.3720.A Shutter unit #956 #398 #1541 #31(1) #1611 #1611 Rear Body #561×2 #1567 #560 #1567 #B823 #1540 #B822 #B824 #1641 #915×2 #B682 #1540 #821 #B682 #1084 #925×3 #248 #1540 #1641 #B820 #247 #244×4 #609 - Ｄ  ･ logo Q0310 forGraphic 070509 Gdesign ito...
  • Page 25 VBA20001-R.3720.A Assembly / Adjustment 1. Rear body #561×2 #1567 #560 #1567 #B823 #1540 #B822 #B824 #1641 #915×2 #B682 #1540 #821 #B682 #1084 #925×3 #248 #1540 #1641 #B820 #247 #244×4 #609 #B823 Position for attaching the double-stick tape for removing dusts around aperture. #B824 #B822 #821...
  • Page 26 VBA20001-R.3720.A Shutter unit Position for attaching [#956] ・With the shutter unit (#31) charged (ready for releasing the shutter), assemble it into the body. ・Attach the conduction plate (#398). ・Tighten two screws (#1611) and one screw (#1541) (in #956 numeric order from #398 .）...
  • Page 27 VBA20001-R.3720.A Charge base plate, I/� base plate, Main condenser Shutter �PC #B326 and other small parts #1572 #1573×3 #1638 #B326 After mounting the charge base plate, make make #614 a mountain fold on the shutter �PC as above, �PC as above, and fit with the boss of the charge base plate.
  • Page 28 VBA20001-R.3720.A 2. �ront body A� drive section, P/� button, Lens contact and other small parts ・As shown in the right middle illustration, position [#B1008] upwards and tighten the screw (#1615). ・Attach [#�1�24� by fitting with the positioning boss of [#26]. ・Make soldering bridges at three places to joint [#B1024] and [#B1008].
  • Page 29 VBA20001-R.3720.A Mirror bo�, � base plate, Release base unit and other small parts Mirror bo� unit Position for hooking the spring (#263) ・Mount the mirror bo� unit (#�211) by fitting it with the boss and the front body. #�211) by fitting it with the boss and the front body. ・Position [#B211] in the direction of the arrow, Position for hooking the spring (#214) and tighten three screws (#1525).
  • Page 30 VBA20001-R.3720.A �ront cover, Bayonet and other small parts Oil barrier: OS-30MEL ※ Apply to the inside of each area so that the grease is not forced out. #1527 #B382 #992 Oil barrier: OS-30MEL #38×2 #407 #1514 #387 #383 #1514 �ront cover unit ・While releasing the aperture-coupled ring (#406) counterclockwise, mount the front cover (#22) on the front body.
  • Page 31 VBA20001-R.3720.A 　Height adjustment of A� coupling shaft ・Set the position of the focus mode select dial to "C". ・Adjust the height of the coupling shaft (#342) to become "1.7±0.2 mm" by using the screw (#359). 　※ ※ When the focus mode is set to "S", [#342] does not move. 　※...
  • Page 32 VBA20001-R.3720.A PD base plate/10 pin terminal ・Assemble the 10-pin terminal (#41) as below, and tighten the screw (#65). ・Attach the 1��pin ��PC (#1�1�) by fitting with the bosses. ・ Put the lens�release SW lug plate (#�8�) by fitting in the screw hole of �#1�1��, and tighten the screw (#15�3). ・Make the solder to joint the 10-pin terminal and the �PC (at nine places), and solder the wire (#1119) of the lens-release SW on the lug plate (#680).
  • Page 33 VBA20001-R.3720.A PD base plate, A� �PC unit and other small parts #968 #293×3 #B1007 A� �PC unit #295×3 ・Put the three adjustment springs (#293) on the front body, and mount the A�-�PC unit (#B1007). ・Turn three screws (#295) clockwise lightly, then give them one turn counterclockwise.
  • Page 34 VBA20001-R.3720.A P. �o� unit #956 #B1005 #1542×2 #1618×2 #955 #871×2 #B1004 #840 #910 #904 #872×2 #891 #837 #874×2 #873×2 #831 #839 #833 #890 #838×2 #1055 #901 #877 #B832 #895A ～ C #876×2 #834 Eyepiece block unit #830 ・As shown in the bottom right illustration, mount the eyepiece block unit, and tighten two screws (#1�1�) to fi�...
  • Page 35 VBA20001-R.3720.A AE �PC unit AE block #883×3 1. Assembly (#B1006) ・Put three AE adjustment springs (#884) on [#B882]. #884×3 ・Mount the AE block (#B1006) on [#B882]. 　※ ※ Mount by fitting the AE adjustment #B882 springs with concave portions of the AE block.
  • Page 36 ② Hexagonal wrench (φ1.5mm） Caution： Do NOT release the shutter. Set the (supplied) tilted mirror with the main mirror being slightly lifted so that the sub-mirror of D300 does not touch the (supplied) tilted mirror of the inspection tool. Eccentric pin for the #1523×2...
  • Page 37 VBA20001-R.3720.A 3. Mounting of �ront body on Rear body Mounting of �ront body on Rear body ・Assemble the front body into the rear body. Then, viewed from the front body, tighten one screw (#1572) and four screws (#1575) in numeric number from ① to ⑤ . ・Tighten two screws (#1531), one screw (#1525), and two screws (#1575).
  • Page 38 (J18��1�1) and the measuring terminal of the gauge, and turn the inde� circle to set to "0". (Reset the digital gauge to "0".）(This is "0"-position of D300.) ・ Measure si� places from the bayonet face to the image PC�...
  • Page 39 VBA20001-R.3720.A Main PCB unit Shutter �PC ・As below, mount [#775] on the body. #1030 #1009 ・Referring to the right picture, connect the Main PCB (#B1001) �PC (#B1005) to the connector of the main PCB (#B1001). ・Mount [#B1001] on the body. ・Tighten three screws (#1616).
  • Page 40 VBA20001-R.3720.A Eyelet, A���assist illuminator protector, ��unction�button e�ternal ring < Adhesive > Adhesive: Super X ※ Apply the adhesive to the 3 places of the inside hole where the function-button e�ternal ring (#788) is assembled. ※ Assemble �#788� by fitting its concave portions with the conve�...
  • Page 41 VBA20001-R.3720.A Mode dial, Trefoil rubber button and other small parts Mode dial �PC unit ・Attach the playback/DEL button (#513) to the top cover. ・Apply the contact grease to the pattern area of [#1025]. ・Mount the mode dial �PC unit on the top cover, and To Top cover Mode dial FPC unit Grease:PL-22S...
  • Page 42 VBA20001-R.3720.A SB case, Syncrho-terminal and other small parts SB lower case unit (#B302) ※ Apply to the surfaces and Grease: AX-115 inside of the holes. #303 Oil barrier: OS-30MEL #305 #322 #796 #1601 Grease: AX-115 #1623×2 ※ Dipping #322 Grease: AX-115 ※...
  • Page 43 VBA20001-R.3720.A Position for hooking the spring (#305) #305 ・Put the SB-up spring (#305) on [#B302], and tighten the screw (#1��1) to fi� on �#3���. #1601 ・Attach [#305] to the hooking part of [#B302]. ・Apply the grease to the contacting area between [#308] and SB wire.
  • Page 44 VBA20001-R.3720.A Outside LCD�PC unit LCD�PC unit ・Attach the compensation/mode button rubber SW (#730) and A�-O� button rubber (#787). ・Apply the grease to the power dial pattern section. ・Connect the mode dial �PC to the connector. Mode dial �PC #787 E�ternal LCD �PC unit #747 ・Mount the outside LCD �PC unit to the top cover.
  • Page 45 VBA20001-R.3720.A Command dial, Shoe base and other small parts Shoe base ・��i� the outside LCD ��PC (#1��3), top cover, and the shoe base firmly with four screws (#321). ・Solder [#1003] and [#B317]. #318 #316 Oil barrier: OS-30MEL Solder #703 　#B317 #948×2 #701 #702...
  • Page 46 VBA20001-R.3720.A SB-PCB ・Solder the four wires on the SB-PCB (#1013). ・Attach the plate (#517) to the top cover, and tighten the screw (#1541). ・Mount the SB-PCB on the top cover, and tighten the screws (#1541, #1511, and #1535). ・As below, connect the �PC of the mode dial (#1025) #517 to the connector.
  • Page 47 VBA20001-R.3720.A Whenever the metering �PC unit is disassembled or replaced, assemble up to the stage of PageA25 without mounting the top cover, and make the AE-CCD positioning adjustment. Top cover unit ・Connect the connection-�PC of [#B23] to the connector of #B23 the body.
  • Page 48 VBA20001-R.3720.A Image sensor holder unit ・Mount the DR base plate (#1014) on the body, and tighten two screws (#1541). ・Connect the �PC (#1045) to the connector of [#1014]. ・Mount the image sensor holder unit (#B10521) on the body. ・Position [#B10521] in the direction of the arrow, and tighten three screws (#1639). ・Solder the wires of [#B10521] on [#1014].
  • Page 49 VBA20001-R.3720.A DG-PCB ・Mount the DG-PCB unit (#B11017) on the body. ・Tighten the screw (#1546). ・Connect the �PCs (#1027, #1038, #1039, #1040, and #1041) to each connector of the DG-PCB. ・Connect the harnesses (#1073, #1074, and #1075) to each connector of the DG-PCB. #1039 #1546 #1074...
  • Page 50 VBA20001-R.3720.A How to connect Camera and PC ★：�ew tool RS232C:MC-21 AC adapter: EH-5 USB cable:UC-E4 J18432 D300 Inspection and Adjustment software Stabilized power supply Set value ＝ 7.4V 　�.3Ω　 5.0A or AC adapter EH-5 �lashmeter (not prepared as RJ) Caution: When voltage is adjusted, use "MB-D10".
  • Page 51 ｍ Color viewer (J63070) ⑦　Start up the inspection and adjustment software for D300 (J18433), and select "Inspection and Adjustment for AE CCD POSITION" then "Set Camera for AE CCD POSITION" to lighten the focus area. Looking through the viewfinder, move the camera so that the focus area of the camera coincide with the grid lines of the AE-CCD positioning tool.
  • Page 52 VBA20001-R.3720.A ⑨ Attach the metering �PC unit with three screws (#883) without tightening up them. Then give each screw one and half turns. By following the instructions of PC, adjust the position of "AE-CCD" with the screws (#883 , and #883 ②...
  • Page 53 VBA20001-R.3720.A Rear cover unit Grease: G-92KA Grease: G-92KA Do �OT apply to #481 the attaching surface of [#481]. #468 Oil barrier: OS-30MEL ※ #924, #961, #962, #985, #986 #985 　#467 #1538×2 #468 #962 #481 #986 　#469 Grease: G-92KA #474 　#476 #961 Grease: G-92KA 　#455...
  • Page 54 VBA20001-R.3720.A T�T monitor and other small parts Oil barrier: OS-30MEL #431 ※ Apply from the front #433 of the rear cover. Oil barrier: OS-30MEL ※ Apply from the back of the rear cover. 　#434×2 #1057 　#488 　#435×2 Grease: G-92KA ※ Apply to the inside of the hole and sliding surface of [#488] [#488] 　#492...
  • Page 55 VBA20001-R.3720.A C� cover, Sponge and other small parts #B423 　#921 #441 #987 　#923 　#445 　#440 #443 #1628×2 #442 Oil barrier: OS-30MEL #923 ※ #440, #442, #921, #923×2, #987 #440 Oil barrier: OS-30MEL Installment of C� cover ・Tighten two screws (#1518). (#1518).
  • Page 56 VBA20001-R.3720.A Bottom cover / Battery lid unit #1571×2 　#807 　#806 　#B63 　 #1556×5 #983 Oil barrier: OS-30MEL #982 　#68 #981 　#47U #1519×4 　#47J ・Mount the bottom cover. ・Tighten three screws (#155�), five screws (#155�) and two screws (#15��). ・Mount the battery lid (#B801). #1556 #1550 #1550...
  • Page 57 VBA20001-R.3720.A I/� rubber unit ・Mount the I/� rubber unit on the body, and tighten two screws (#1642). #392 #394 #1642×2 E�ternal rubber ・Attach the e�ternal rubbers (#���, #��1, #��3, and #�447). ・Attach the grip rubber (#���) firmly with the screw (#1�47). #B447 #1647 #B61...
  • Page 58 VBA20001-R.3720.A D300 Inspection and Adjustment Software (J18433) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. IBM PC/AT compatible...
  • Page 59 The file (D3��Soft.EXE) of this program is provided via ��D or e�mail. �ecause this is the self�e�tracting file, decompress the file before installing, and follow the ne�t procedure. 1. Create a folder for installation under any drive and name. C: ￥DeskTopLauncher\D-SLR\D300 2. Paste the file (PD300.EXE) in the created folder.
  • Page 60 4. When "Add New Hardware Wizard" is displayed, click "Ne�t". 5. Select "Search for a better drive than the one your device is using now. (Recommended)", and click "Ne�t". 6． Click "Reference". Select "DeskTopLauncher\D-SLR\D300\PTPC\" of C drive, and click "OK". 7. The install is completed.
  • Page 61 VBA20001-R.3720.A <Start-up of Program> 1. Double�click the file (D3��.e�e), then �nspection and adjustment program for D3�� starts. 2. To display in Japanese, select the radio button "JAPA�ESE" in "LA�GUAGE" in the lower right-hand corner of the screen. 　However, this is not properly viewed in the English OS. 3.
  • Page 62 VBA20001-R.3720.A AE inspection and adjustment 《USB connection communication》 ① AE CCD alignment inspection and adjustment (ref. Page A27 and 28 for details） ② AE accuracy inspection and adjustment 《USB connection communication》 ③ Aperture accuracy inspection 《USB connection communication》 ④ �uilt�in S� flash inspection and adjustment 《USB connection communication》...
  • Page 63 VBA20001-R.3720.A ∞ �nfinity focus inspection & adjustment ・Replace the finder screen with the infinity focus check screen (J183�4), and use the reference lens (J18�1�) and read the value. In case it is out of standard, increase or decrease washers (#836A, #836B, #836C or #836D) for adjustments.
  • Page 64 VBA20001-R.3720.A Necessary adjustments when parts are replaced 1. D300 adjustment software and updates 　　　　Adjustments Writing of AE CCD accuracy Aperture Built-in SB Battery EEPROM positioning inspection & accuracy light volume check volt- accuracy fixed adjustment adjustment inspection inspection & age level inspection &...
  • Page 65 VBA20001-R.3720.A 2. Shooting image adjustment software and Software updates Adjustments Serial GrGB Dark Sensi- Shading Gr/Gb Sensi- Image Pixel Pixel Initial Version code differ. current tivity adjust- compen- tivity shutter defect defect adjust- settings No. / input data comp. adjust- adjust- ment sation...
  • Page 66 When D300 shooting image-related and listed parts on Page A42 are replaced, be sure to make an adjustment by the shooting image adjustment software for D300 (J65107). The details of its function and how to use this software are as follows: 2.
  • Page 67 VBA20001-R.3720.A 5. Basic usage 　(1) E�ecute "D3���MG.e�e" to start up the main screen. (ref. ��ig.1) 　(2) Select E�GLISH / JAPA�ESE in Language to display the appropriate menu. (ref. �ig.2) 　(3) Click the button to start adjustments. ※ When the adjustments from 1. to 6. are made, calculate to get the "Sensitivity" and "Sensitivity ratio" reference values by using the reference body beforehand, then perform the adjustments.
  • Page 68 VBA20001-R.3720.A 6. Required device and conditions ※ AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not ★ �ew tool particularly mentioned in the list. Item Required device Setting/Remarks 1 Gr/Gb difference compensation ・5100K color viewer　　...
  • Page 69 VBA20001-R.3720.A 7. Summary 　The summary on each adjustment is as follows: (1) Gr�Gb difference compensation adjustment (G filter; G�line crawl only) 　　・When the DG-PCB is replaced, write the serial number. 　　・When the DG-PCB or image sensor holder unit is replaced, write the unique data.　　 ��irst, take a picture of the QR code that is attached to the image sensor holder unit, then read the shot image with the hand scanner.
  • Page 70 VBA20001-R.3720.A (7）Image shutter adjustment �ased on the 1�125 sec. data of LV�, fine�tune the 1�8��� sec. data of LV15. After the adjustment, inspect the data deviation at nine points of the shot image. （8）Pi�el defect compensation � black point When pi�els of which the output level is under specified value with LV13 equiv. are detected, the coordinates of the detected pi�els are additionally written as pi�el defect compensation data.
  • Page 71 VBA20001-R.3720.A 8. Procedure 8-1. Shooting image adjustment 　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D3�� reference body beforehand, then perform the adjustments. (ref. 9-4.) 　● ��or shooting image adjustment, make all items from (1) to (7). The adjustments from (1) through (7) are all programmed to be e�ecuted in serial order.
  • Page 72 VBA20001-R.3720.A ●Gr�Gb difference compensation adjustment (G filter) 　・Attach the tool lens (Aperture ��5.�) and SP2 (G filter) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・The software automatically goes on to the ne�t adjustment item.
  • Page 73 VBA20001-R.3720.A （7）Image shutter adjustment 　・Click "�. �MAGE SHUTTER �NS. & ADJ." of the main menu on screen. 　・Attach the tool lens (Aperture �5.6) to the camera. 　・Get the camera closest to the center of the illuminated surface of the shutter tester. 　・...
  • Page 74 VBA20001-R.3720.A 8-4.TFT adjustment 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Turn the camera O�. 　 　Hue adjustment 　・Usually the default value is used, and the adjustment is not necessary. 　・If there is some problem with hue by visual check, operate the slider to make the adjustment. 　・Remove the USB cable from the camera.
  • Page 75 VBA20001-R.3720.A 8-6. Version No./Serial No. 　・Provide the power for the camera via AC adapter. 　・Set "PTP" mode by Setup menu. 　・Connect the camera and PC via USB cable. 　・Click "RISC VERSIO�" of the menu on screen. 　・RISC version number/Serial number will be displayed. 　＊...
  • Page 76 VBA20001-R.3720.A 11. Setting of two-dimensional barcode reader Reference: To avoid reading errors, use ・Insert the two-dimensional barcode reader a masking sheet of the left into the USB terminal. picture, which is supplied with ・Read the bar codes shown below. a two dimensional barcode reader.
  • Page 77 VBA20001-R.3720.A ・Insert the CD-ROM which is supplied with a two-dimensional barcode reader into the PC. ・Click "Reference" and select "IT4200" in the CD-ROM folder. ・Click "�inish" and take out the CD-ROM from the PC. - Ａ  ・ logo Q0310 forGraphic 070509 Gdesign ito...
  • Page 78 VBA20001-R.3720.A ・Open "Device Manager" and confirm the port setting. Click the right mouse button on "My Computer". Then, select the items in the following order: �Properties� → �Hardware� → �Device Manager�. Note:The port setting differs depending on the PC environment. e.g.
  • Page 79 VBA20001-R.3720.A Paralla� inspection and adjustment Caution：When "Separate Prism bo� from ��ront body" is performed, be sure to make the adjustment. Procedure ①　 　 �nsert the battery into the camera, and set the e�posure mode to "P". 　①　 　②　 　 Turn the power SW to O��, and remove the battery. (By this procedure, the camera memorizes the latest set mode in the camera.) ③　...
  • Page 80 VBA20001-R.3720.A A� XY adjustment X adjustment corrects the position of the A�� ��PC unit in X�a�is direction by the screw, and also makes the electrical fine�adjusutment in XY�a�is directions. Caution: Whenever the A� �PC unit is disassembled or replaced, be sure to make the X/Y adjustment. Procedure Make the adjustment, based on the A�...
  • Page 81 VBA20001-R.3720.A ＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, set the MB-D200 and wire as follows. * Modify "MS-D10" and connect wires. － ＋ ＋ － Ａ ＭＢ－Ｄ１０ Test item Standard Test condition Main SW・O��...
  • Page 82 VBA20001-R.3720.A Penta prism and SI dust cleaning in LCD 《Cleaning without removing Screen bo�》 ・ Take out two screws (#1504), and remove the mirror receiving part. Screen bo� #1504×2 ・ Release the claw (indicated by the arrow) of the screen�bo� retaining plate (#830), and lower [#830].
  • Page 83 BLACK CONNECTED WITH BLACK SOLDERING BRIDGE APERTURE APERTURE START Mg BLACK STOP Mg CONNECTED WITH BLACK THIS CONNECTOR ｺﾈｸﾀ接続 YELLOW YELLOW BLUE ORANGE WHITE BLUE MIRROR BLACK CONNECTED WITH UP Mg THIS CONNECTOR GREEN 青 黒 緑 ー E1・D300 ー...
  • Page 102 VBA20001-R.3720.A Inspection standards Items Judgment standard Remarks External view Btwn top cover & apron: 0.2 mm or less Visual check Step Other parts: 0.3 mm or less Digital micrometer (height difference) Moving parts: 0.5 mm or less Visual check Btwn Top cover & Apron: 0.2 mm or less Thickness gauge Btwn Top display panel window (surrounding) &...
  • Page 103 VBA20001-R.3720.A Items Judgment standard Remarks AF accuracy Center：�� 4 mrad Special tool Others: �� 0 mrad Brightness box Pitch Center：�� 5 mrad Others: ��  mrad Others than Side: 0 ± 50 μm Block Def amount Side: 0 ± 60 μm AF-assist illuminator AF50/.4D　...
  • Page 104 VBA20001-R.3720.A Items Judgment standard Remarks Viewfinder Inner LCD lower Up-down position: No outstanding misalignment Visual check panel window position Tilt: １° or less AF50/.4D, F5.6 Looking through viewfinder, measure Finder field frame Lens vignetting/distortion: No outstanding vignetting/distortion a tilt of indication Tilt: (based on Bottom cover): 30’...
  • Page 105 VBA20001-R.3720.A Items Judgment standard Remarks Main SW / OFF: 150 μA or less Standby (idle) / Constant-voltage power source (5A or consumed current （Do NOT press any operational buttons.） more) Main SW / ON (Half-release timer: OFF): 150 μA or less Battery tool (J623) Main SW / ON (Half-release timer: ON): 220 ｍ...
  • Page 106 VBA20001-R.3720.A Items Judgment standard Remarks Battery life General mode 　Room temperature: 600 frames or more EN-EL3e 　0℃ 400 frames or more AF-S24-20/3.5-5.6 VR OFf, AF-C, Release mode dial: S, M/250 F5.6, AF scan reciprocating motion once → Halfway press 6 sec. → Release once → TFT monitor 2 sec. → Half-release timer OFF (repeat) Professional mode 　Room temperature: 3200 frames or more...
  • Page 107 VBA20001-R.3720.A Items Judgment standard Remarks Image-related Judgment method AF50mm/F.4D(CPU Appropriate level When RAW recorded: built-in metering Within the area of 425 pixels ｘ 425 pixels at the center of reference lens) screen, calculate the average of G-2 bit data. F5.6 When TIFF/JPEG recorded: ISO00 /30 LV0 Within the area of 425 pixels ｘ...
  • Page 108 VBA20001-R.3720.A Items Judgment standard Remarks Resolution Judgment method AFS80-200mm/F2.8D When TIFF/JPEG recorded: 05mm Take a shot by matching the angle of view of the chart’s vertical F5.6 direction. AE: M mode Adjust the speed so that brightness becomes 220 �� 5LSB (8bit) at white Image quality: TIFF/JPEG part about the center of chart.
  • Page 109 VBA20001-R.3720.A 工具・ＴＯＯＬＳ ★：新規設定工具・NEW TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J15259 ＡＦ調整工具台 AF ADJUSTING TOOL J15280 Ｚレンズ用支持ホルダー LENS HOLDER J15264 高周波タイプ蛍光灯器具 ILLUMINATION BOX FOR AF ADJUSTMENT J15407 マルチカム２０００　ＡＦチャート FOR D2SERIESE MULTI CAM 2000 AF CHART J15409 チャートボード FOR D2SERIES, D40 CHART BOARD J18001-1...
  • Page 110 VBA20001-R.3720.A ★：新規設定工具・NEW TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others J18358 ＮＤフィルター４× ２枚使用 ND FILTER 4X IT USES BY TWO PIECES. J18389 反射ミラー FOR D200,D80 REFLECTION MIRROR J18394 無限合致調整用スクリーン FOR D200,D80 INFINITY FOCUS ADJUSTMENT SCREEN J18433 カメラ部調整用ソフト ADJ. SOFT FOR CAMERA J19001 ∞合致コリメーターＦ＝６００ｍｍ...
  • Page 111 FOR D2H,D70,D70s,D50, FILTER SP3 D200,D80,D40,D40x J65096 ＱＲリーダーソフト FOR S10, ETC QR READER SOFTWARE J63100 Ｄ３００用ＡＥ　ＣＣＤ用チャートボード ★ AE/CCD USE CHART BOARD FOR D300 J63101 Ｄ３００用ＡＦ　Ｘ－Ｙチャート ★ AF X-Y CHART FOR D300 J63103 Ｄ３００用視差・ＳＩチャート ★ PARALLAX/SI CHART FOR D300 - T ･...
  • Page 112 VBA20001-R.3720.A ★：新規設定工具・NEW TOOL 工具番号 名　称 備　考 Tool No. Name of tool Others C-8008B セメダイン　８００８（黒） CEMEDAIN 8008(BLACK) EDB0011 ネジロック（赤）１４０１Ｃ SCREW LOCK 1401C LEN317A グリース　ＬＥＮ３１７Ａ GREASE LEN317A OS-30MEL ドライサーフ　ＯＳ－３０ＭＥＬ ＯＳー３０ＭＦ使用可 DRY SURF OS-30MEL (OIL BARRIER) OS-30MF IS AVAILABLE アロンアルファ 汎用品 QUICK DRYING GLUE RJ IS NOT AVAILABLE 汎用品...

Table of Contents