Chart Of Image Adjustment Procedures - Kyocera ECOSYS M3040dn Service Manual

(5) Chart of image adjustment procedures

Adjust-
Item
ing order
1 Adjusting the center line of the MP
tray
(printing adjustment)
Adjusting the LSU print start timing
2 Adjusting the center line of the cas-
settes
(printing adjustment)
Adjusting the LSU print start timing
3 Adjusting the leading edge registra-
tion of the MP tray
(printing adjustment)
secondary paper feed start timing
4 Adjusting the leading edge registra-
tion of the cassette
(printing adjustment)
secondary paper feed start timing
5 Adjusting the leading edge margin
(printing adjustment)
LSU illumination start timing
6 Adjusting the trailing edge margin
(printing adjustment)
LSU illumination end timing
Maintenance mode
Image
Page
Item No. Mode
U034 LSU Out Left P.1-3-24
(Original:test pattern)
U034 LSU Out Left P.1-3-24
(Original:test pattern)
U034 LSU Out Top P.1-3-24
(Original:test pattern)
U034 LSU Out Top P.1-3-24
(Original:test pattern)
U402 Lead P.1-3-51
(Original:test pattern)
U402 Trail P.1-3-51
(Original:test pattern)
Setting procedure
Method
1. Press the start key. 1. Change the setting value using
2. Select [Lsu Out Left] to be adjusted. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
4. Press the system menu key. is set.
5. Press the start key.
(output a test pattern) Completion: Press the stop key.
6. Press the system menu key.
7. Select [MPT] to be adjusted.
1. Press the start key. 1. Change the setting value using
2. Select [Lsu Out Left] to be adjusted. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
4. Press the system menu key. is set.
5. Press the start key.
(output a test pattern) Completion: Press the stop key.
6. Press the system menu key.
7. Select the item to be adjusted.
[Cassette1] to [Cassette7]
1. Press the start key. 1. Change the setting value using
2. Select [Lsu Out Top] to be adjusted. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
4. Press the system menu key. is set.
5. Press the start key.
(output a test pattern) Completion: Press the stop key.
6. Press the system menu key.
7. Select [MPT(L)] or [MPT(S)] to be
adjusted.
1. Press the start key. 1. Change the setting value using
2. Select [Lsu Out Top] to be adjusted. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
4. Press the system menu key. is set.
5. Press the start key.
(output a test pattern) Completion: Press the stop key.
6. Press the system menu key.
7. Select [Cassette(L)] or [Caseette(S)] to
be adjusted.
1. Press the start key. 1. Change the setting value using
2. Press the system menu key. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
(output a test pattern) is set.
4. Press the system menu key.
5. Select [Lead] to be adjusted. Completion: Press the stop key.
1. Press the start key. 1. Change the setting value using
2. Press the system menu key. the cursor +/- or numeric keys.
3. Press the start key. 2. Press the start key. The value
(output a test pattern) is set.
4. Press the system menu key.
5. Select [Trail] to be adjusted. Completion: Press the stop key.
2-3-13
2NM/2NX/2NY/2NZ/2P0/2P6
Remarks
Setting
If a preset value is raised, a picture will move to
the left.
To make an adjustment for duplex copying,
select [Dup].
If a preset value is raised, a picture will move to
the left.
To make an adjustment for duplex copying,
select [Dup].
If a preset value is raised, a picture will move
downward.
To make an adjustment for duplex copying,
select [Dup].
If a preset value is raised, a picture will move
downward.
To make an adjustment for duplex copying,
select [Dup].
A margin will become large if a preset value is
raised.
A margin will become large if a preset value is
raised.