Message List; Error Messages - Yamaha RX-A1000 Owner's Manual

■

Message list

NOTE
If the following messages appear, resolve the problems that have occurred and carry out the
measurement process again.
■ When a warning message is displayed before measurement
Connect MIC!
The YPAO microphone is not connected.
Unplug HP!
The headphones are connected.
Memory Guard!
The settings of this unit are protected.

■ Error messages

E-1:
The unit was not able to find the front
No Front SP
channel.
E-2:
The unit was only able to find one of side of
No Sur. SP
the surround channels.
E-3:
The unit was only able to find one of side of
No F.PRNS SP
the presence channels.
E-4:
Only one surround back speaker is
SBR→SBL
connected and only the right side surround
back channel sound is detected.
E-5:
The noise is too loud, preventing accurate
Noisy
measurements from being taken.
E-6: Even though surround left and right speakers
Check Sur. are not connected, only the surround back
speakers are connected.
E-7: The YPAO microphone has been removed.
No MIC
Connect the YPAO microphone to the YPAO
MIC jack on the front panel.
Remove the headphones.
Set "Memory Guard" in the Setup menu to "Off"
(☞p. 103).
Check that the left and right front speakers are
connected correctly.
Check that the left and right surround speakers
are connected correctly.
Check that the left and right presence speakers are
connected correctly.
When only one surround back speaker is
connected, connect to the left side (SINGLE)
terminal.
Measure again in quiet surroundings. Turn off any
devices in the room that may be emitting noise, or
place them further away from the YPAO
microphone.
When this message is displayed, selecting
"PROCEED" will allow you to continue
measuring. However, we recommend resolving the
problem and measuring again, as continuing
measurement without doing so will not give
accurate results.
When using surround back speakers, connection of
the surround left/right speakers is necessary.
While measuring, take care not to touch the
YPAO microphone.
Setting up the speaker parameters automatically (YPAO)
E-8:
The YPAO microphone could not
No Signal
distinguish a test tone.
E-9:
You have carried out an operation that has
User Cancel
cancelled the measuring process.
E-10:
An internal error has occurred.
Internal Error
■ Warning messages
W-1: The speakers displayed are connected with
Out of Phase
the opposite polarity. Depending on the type
of speakers you are using and the
environment in which you have them
installed, this message may occur even if the
speakers are connected correctly.
W-2:
The speakers displayed are separated from
Over 24m/80ft
the listening position by more than 24 m,
and cannot be adjusted correctly.
W-3:
Volume level varies greatly for individual
Level Error
channels, and cannot be adjusted correctly.
If "W-2" or "W-3" appears, you can apply measurement results, but they will not give optimal
results. We recommend that you resolve the problem and carry out the measurement process again.
CONNECTIONS
Check that the YPAO microphone has been
installed correctly.
Check that each speaker has been connected and
installed correctly.
The YPAO microphone or the YPAO MIC jack
may be broken. Inquire at the retailer where you
purchased this unit, or the nearest Yamaha service
center.
Carry out the measuring process again. Do not
operate this unit by, for example, adjusting the
volume.
Carry out the measuring process again. Contact a
Yamaha service center if "E-10" is displayed
again.
Depending on the type of speakers, "W-1" may
display even if the speakers are connected
correctly.
Check that the speaker polarity + (positive), and -
(negative) are correct. If these are connected
correctly, you can use the speakers normally even
this message appears.
Install the speakers with 24 m of the listening
position.
Check that all speakers are installed in the same
surroundings.
Check that the speaker polarity + (positive), and -
(negative) are correct.
We recommend the same speakers or speakers
with as similar specifications as possible.
Adjust the volume of the subwoofer.
43
En