Jonsered FR 2213 MA Operator's Manual
Jonsered frontrider operator's manual
Hide thumbs
Also See for FR 2213 MA:
- Operator's manual (36 pages) ,
- Workshop manual (68 pages) ,
- Operator's manual (32 pages)
Related Manuals for Jonsered FR 2213 MA
Summary of Contents for Jonsered FR 2213 MA
- Page 1 Oper ator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine. FR 2213 MA FR 2216 MA FR 2216 MA 4X4...
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols Ignition These symbols are on the machine and in the instructions. Hydrostatic freewheel WARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Warning: rotating parts. Keep hands and feet clear. - Page 3 KEY TO SYMBOLS Drive very slowly if no cutting unit is fitted Cutting deck must be fitted before driving at full speed. Starting instructions Check the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit Apply and lock the parking brake. If the engine is cold, use the choke Release the parking brake before driving Switch off the engine and take off the...
-
Page 4: Table Of Contents
CONTENTS Contents Checking the cutting unit’s parallelism ......Adjusting the parallelism of the cutting unit ....KEY TO SYMBOLS Service position for the cutting unit ......Symbols ............... Checking the blades ............. CONTENTS Replacing the blades ............ Contents ..............Removing the Mulching plug ........INTRODUCTION Lubrication Dear Customer, ............ -
Page 5: Introduction
Dear Customer, Thank you for choosing a Jonsered Frontrider. Jonsered Frontriders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. FrontRiders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine. -
Page 6: Service Journal
Service journal Pre-delivery service 12 Tell customer about: Needs and benefits of following the service 1 Charge the battery for 4 hours at max. 3 amp. schedule. 2 Fit steering wheel, seat and any optional The transmission warranty is only valid if front equipment. -
Page 7: What Is What
WHAT IS WHAT? Location of the controls 1 Throttle control/choke control 9 Product and serial number plate 2 Ignition lock 10 Seat adjustment. 3 Cutting height adjustment lever 11 Lever to disengage the driving front axle, FR2216MA 4X4 4 Lifting lever for the cutting unit 12 Fuel cap 5 Speed limiter for reversing 13 Cover lock... -
Page 8: Safety Instructions
SAFETY INSTRUCTIONS Safety instructions • Remember that the driver is responsible for dangers or accidents. These instructions are for your safety. Read them carefully. • Never carry passengers. The machine is only intended to be used by one person. Insure your Rider •... -
Page 9: Driving On Slopes
SAFETY INSTRUCTIONS Driving on slopes • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may regulate the age of the user. Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest;... -
Page 10: Children
SAFETY INSTRUCTIONS Maintenance • Do not try to stabilize the machine by putting your foot on the ground. • Stop the engine. Prevent the engine from starting by • When cleaning the chassis, the machine may never be removing the ignition key before making any adjustments driven near verges or ditches. -
Page 11: Transport
SAFETY INSTRUCTIONS • Take care with battery maintenance. Explosive gases • Reduce the risk of fire by removing grass, leaves and form in the battery. Never perform maintenance on the other debris that may have fastened on the machine. battery while smoking or in the vicinity of open flames or Allow the machine to cool before putting it in storage. -
Page 12: Presentation
Otherwise there is a risk you may lose control. Cutting unit FR 2213 MA, FR 2216 MA and FR 2216 MA 4X4 have a Combi-unit 1 Press down the parking brake pedal. 2 Press in the lock button on the steering column. -
Page 13: Cutting Height Adjustment Lever
PRESENTATION Cutting height adjustment lever Release lever FR 2213 MA, FR 2216 The cutting height can be adjusted to 7 different positions with the cutting height lever. The release control must be pulled out in order for the Combi-unit 30-80 mm machine to be moved when the engine is shutoff. -
Page 14: Driving
Driving Before starting Start the engine • Read the safety instructions and information concerning 1 Make sure that the clutch control is depressed. FR 2216 the placement of controls and functions before starting. MA 4X4 has one control for the front axle and one control for the rear axle. -
Page 15: Starting The Engine With A Weak Battery
Driving Starting the engine with a weak With a warm engine: battery 5 Move the throttle in between positions 1 and 2. WARNING! Lead-acid batteries produce explosive gases. Avoid sparks, open flames and smoking close to batteries. Always wear protective glasses in the vicinity of batteries. If the battery is too weak to start the engine, it should be recharged. -
Page 16: Driving The Rider
Driving Driving the Rider Stop the engine 1 Release the parking brake by first pressing down the Always park the machine on a level surface with the engine parking brake pedal and then releasing it. OFF. 1 Lift up the cutting unit by pulling the lever backwards to its locked position. -
Page 17: Maintenance
Maintenance Maintenance schedule The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised service workshop. Daily maintenance At least once a Maintenance Maintenance before starting year interval in hours 100 200... -
Page 18: Cleaning
Maintenance Cleaning Removing of the machine hoods Clean the machine directly after use. It is much easier to wash Engine cover off grass cuttings before they dry. The engine becomes accessible for service when the engine cover is opened. Fold the seat forward, loosen the snap lock under the seat and fold the cover backwards. -
Page 19: Muffler
Maintenance Muffler 4 If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Check regularly that the muffler is complete and secured Do not over tighten the cables; they should only be drawn correctly. -
Page 20: Adjusting The Parking Brake
Maintenance Adjusting the parking brake Adjusting the throttle wire FR 2213 MA, FR 2216 MA The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces Check that the brake is correctly adjusted by placing the black smoke or maximum revs are not reached. -
Page 21: Replacing The Air Filter
Maintenance Replacing the air filter Replacement of fuel filter If the engine seems to lack power or does not run smoothly Replace the fuel filter every 100 running hours (once per this may be because the air filter is clogged. It is therefore season) or more frequently if it is clogged. -
Page 22: Ignition System
Maintenance Ignition system Check the safety system The engine is equipped with an electronic ignition system. The machine is equipped with a safety system that prevents Only the spark plug requires maintenance. starting or driving under the following conditions. For recommended spark plug, see Technical data. The engine can only be started when: IMPORTANT INFORMATION •... -
Page 23: Checking And Adjustment Of The Cutting Unit's Ground Pressure
Maintenance Checking and adjustment of the Adjusting the parallelism of the cutting unit’s ground pressure cutting unit To achieve the best cutting results the cutting unit should 1 Remove the front cover. follow the underlying surface without pressing too hard 2 Unscrew the belt shield. -
Page 24: Service Position For The Cutting Unit
Service position for the cutting unit 6 Loosen on the cutting height stay and place in the holder. FR 2213 MA, FR 2216 MA The cutting head can be placed in the service position to provide easy access for cleaning, repairs and servicing. In the service position the cutting unit is raised and locked in the vertical position. -
Page 25: Checking The Blades
The risk increases if the blades are poorly balanced. WARNING! Wear gloves to protect your FR 2213 MA, FR 2216 MA, FR 2216 MA 4X4 hands when working with the blades. • Put the unit in the service position, see Service position for the cutting unit. -
Page 26: Lubrication
Lubrication Checking the engine’s oil level. Replacing the engine oil Check the oil level in the engine when the Rider stands The engine oil should be changed the first time after 8 hours horizontal with the engine switched off. Do not check the oil running time. -
Page 27: Changing The Oil Filter
General lubrication 2 Check that there is oil in the transmission’s oil tank. FR 2213 MA, FR 2216 MA Fill if necessary with engine oil All joints and bearings are lubricated using molybdenum SAE 10W/40 (class SF–CC). disulphide grease during manufacture. Continue to lubricate using the same type of grease *. -
Page 28: Troubleshooting Schedule
Troubleshooting schedule Problem Cause There is no fuel in the fuel tank Faulty spark plug. Defective ignition cable. Engine does not start Dirt in the carburettor or fuel line Starter motor does not turn over the engine Defect safety switch Battery flat Bad contact between the cable and battery Lift lever for cutting unit in wrong position... -
Page 29: Storage
Storage Winter storage Guard At the end of the season, or if the machine is going to stand There is a cover to protect your machine during storage or idle for more than 30 days, it should immediately be made transport. -
Page 30: Technical Data
TECHNICAL DATA FR 2213 MA FR 2216 MA FR 2216MA 4X4 Dimensions Length without cutting unit, mm/ft 2010/6,58 2010/6,58 2010/6,58 Length with cutting unit, mm/ft 2230 / 7,32 2230 / 7,32 2230 / 7,32 Width without cutting unit, mm/ft 880/2,89... -
Page 31: Ec Declaration Of Conformity
EC Declaration of Conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Jonsered FR 2213 MA, FR 2216 MA and FR2216 MA 4X4 from 2014’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE:... - Page 32 Original instructions 1156991-26 ´®z+X•,¶6;¨ ´®z+X•,¶6;¨ 2014-06-27...