Brother HL-5440D Service Manual page 124

Location of screw
Under bar earth plate L
Under bar
(Front left side)
Under bar (Rear side)
(HL-6180DW/6180DWT only)
Main frame L ASSY
Drive
HL-5440D
sub
ASSY
Except for HL-5440D
Main motor ASSY
Main motor cover
MP solenoid
Main PCB shield calking ASSY
Duplex solenoid
Bottom frame L
Base plate
High-voltage power supply PCB
ASSY
T1 paper feed actuator holder
ASSY
Main frame R
MP feed frame
MP paper empty sensor PCB
ASSY
T2 tray cover
T2 side cover L
T2 side cover R
T2 front cover ASSY
Under bar (Two)
T2 frame R unit
T2 paper feed frame unit
T2 front beam
T2 paper feed actuator holder
ASSY
T2 back cover
Screw type
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M3x10
Taptite bind B M3x10
Taptite bind B M4x12
Taptite bind B M3x10
Taptite bind B M4x12
Taptite bind B M4x12
Screw pan (S/P washer)
M3x12 DB
Taptite bind B M4x12
Taptite bind B M3x10
Taptite bind B M4x12
Taptite bind B M3x10
Taptite bind B M3x10
Taptite bind B M4x12
Taptite bind B M4x12
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M3x10
Taptite bind B M4x12
3-5
Tightening torque
Q'ty
N.m (kgf.cm)
1
0.8±0.1(8±1)
1
2 0.8±0.1(8±1)
3 0.8±0.1(8±1)
4 0.8±0.1(8±1)
8 0.8±0.1(8±1)
1 0.5±0.1(5±1)
9 0.8±0.1(8±1)
4 0.8±0.1(8±1)
2 0.5±0.1(5±1)
1 0.5±0.1(5±1)
4 0.8±0.1(8±1)
1 0.5±0.1(5±1)
3 0.8±0.1(8±1)
4 0.8±0.1(8±1)
2 0.45±0.05(4.5±0.5)
2 0.8±0.1(8±1)
1 0.5±0.1(5±1)
5 0.8±0.1(8±1)
2 0.5±0.1(5±1)
1 0.5±0.1(5±1)
2 0.8±0.1(8±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
4 0.8±0.1(8±1)
2 0.8±0.1(8±1)
2 0.8±0.1(8±1)
3 0.8±0.1(8±1)
2 0.8±0.1(8±1)
1 0.5±0.1(5±1)
2 0.8±0.1(8±1)
Confidential