Video Sockets - TANDBERG Codec 3000 MXP Reference Manual

Interfaces and Sockets – Codec 3000

Video Sockets

NoTe! The system S-video input
will automatically Mini-DIN socket
adapt to a PAL or Aux. camera
NTSC input.
Single
S-video output
Mini-DIN socket
DVI-I pin-out
Pin
Note: TANDBERG supports DVI-D
Single-Link, DVI-A and DVI-I Sin-
gle-Link format cables.
DVI-D cables transmit digital
T.M.D.S. signals, DVI-A cables
transmit analogue VGA signals
and DVI-I cables can transmit
either digital or analogue signals.
If your DVI cable is not long
enough, use extension cables.
C1
Observe, however, that the
maximum cable length should not
C4
exceed 5 m to avoid quality loss.
D 13887.08
MAY 2008
MXP
Composite video input RCA sockets
Doc. camera VCR
Single Dual DVI output
Composite video output
RCA sockets
DVI-I Pin-out
Assignment Pin Assignment
1 T.M.D.S. Data 2– 9 T.M.D.S. Data 1–
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+
3 T.M.D.S. Data 2/4 11 T.M.D.S. Data 1/3
Shield Shield
4 T.M.D.S. Data 4– 12 T.M.D.S. Data 3–
5 T.M.D.S. Data 4+ 13 T.M.D.S. Data 3+
6 DDC Clock 14 +5 V power
7 DDC Data 15 GND
(return for +5 V,
HSync and Vsync)
8 Analogue Vertical 16 Hot plug detect
Sync
Analogue Red C2 Analogue Green
Analogue C5 Analogue GND
Horizontal Sync (analogue
R, G & B return)
PC DVI-I input sockets
(Digital Video Interface,
Integrated digital
and analogue)
Pin Assignment
Formats supported on DVI-I out:
17 T.M.D.S. Data 0–
SVGA (800 × 600) 75 Hz
XGA (1024 × 768) 60 Hz
18 T.M.D.S. Data 0+
SXGA (1280 × 1024) 60 Hz
HD720p (1280 × 720) 50 Hz, 60 Hz
19 T.M.D.S. Data 0/5
WXGA (1280×768) 60 Hz
Shield
Formats supported on DVI-I in:
20 T.M.D.S. Data 5–
SVGA (800 × 600) 60 Hz, 72 Hz, 75 Hz, 85 Hz
21 T.M.D.S. Data 5+
XGA (1024 × 768) 60 Hz, 70 Hz, 75 Hz
SXGA (1280 × 1024) 60 Hz
22 T.M.D.S. Clock
HD720p (1280 × 720) 50 Hz, 60 Hz
Shield
Do as follows to get WXGA:
23 T.M.D.S. Clock+
1 VGA Out Quality must be set to Auto.
2 VGA Monitor Format
3 PC Picture Format
24 T.M.D.S. Clock–
If you are using TANDBERG supplied monitors this will give WXGA out
when displaying graphics.
C3 Analogue Blue
If non-TANDBERG provided displays are used, you must in addition
execute the command:
xConfiguration Video Outputs AllowWXGA: On
23
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
Levels
Composite: 1 Vpp, 75 W
S-Video (Y/C):
Y: 1 Vpp, 75 W
C (PAL): 0.3 Vpp, 75 W
C (NTSC): 0.28 Vpp, 75 W
must be set to Wide.
must be set to Normal.
TANDBERG 3000 MXP & 6000 MXP
S-video Mini-DIN pin-out
External view of socket
4
3
2
1
Pin 1: Ground (Luminance)
Pin 2: Ground (Chrominance)
Pin 3: Luminance (Y)
Pin 4: Chrominance (C)
RCA pin-out
External view of socket
Signal GND