HP A7533A - Brocade 4Gb SAN Switch Base Administrator's Manual page 233
Hp storageworks fabric os 6.x administrator guide (5697-0015, may 2009)
Hide thumbs
Also See for A7533A - Brocade 4Gb SAN Switch Base:
- Administrator's manual (576 pages) ,
- Hardware reference manual (256 pages) ,
- User manual (248 pages)
Table of Contents
Advertisement
•
Target B has WWN 50:05:07:61:00:49:20:b4 (connected to switch2).
The following procedure shows how to control device communication with the LSAN.
To control device communication with the LSAN:
1.
Log in as admin and connect to switch1.
2.
Enter the nsShow command to list the WWN of the host (10:00:00:00:c9:2b:c9:0c).
NOTE:
The nsShow output displays both the port WWN and node WWN; the port WWN must be used
for LSANs.
switch:admin> nsshow
{
Type Pid
COS
N
060f00;
2,3;
FC4s: FCP
NodeSymb: [35] "Emulex LP9002 FV3.91A3
Fabric Port Name: 20:0f:00:05:1e:37:00:44
Permanent Port Name: 10:00:00:00:c9:2b:c9:0c
The Local Name Server has 1 entry }
3.
Enter the zoneCreate command to create the LSAN lsan_zone_fabric75, which includes the host.
switch:admin> zonecreate "lsan_zone_fabric75", "10:00:00:00:c9:2b:c9:0c"
4.
Enter the zoneAdd command to Target A to the LSAN.
FID75Domain5:admin> zoneadd "lsan_zone_fabric75", "50:05:07:61:00:5b:62:ed"
5.
Enter the cfgAdd or cfgCreate and cfgEnable commands to add and enable the LSAN
configuration.
switch:admin> cfgadd "zone_cfg", "lsan_zone_fabric75"
switch:admin> cfgenable "zone_cfg"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'zone_cfg' configuration
zone config "zone_cfg" is in effect
Updating flash ...
6.
Log in as admin to fabric2.
7.
Enter the nsShow command to list Target A (50:05:07:61:00:5b:62:ed) and Target B
(50:05:07:61:00:49:20:b4).
switch:admin> nsshow
{
Type Pid
COS
NL
0508e8; 3;
FC4s: FCP [IBM
Fabric Port Name: 20:08:00:05:1e:34:11:e5
Permanent Port Name: 50:05:07:61:00:5b:62:ed
NL
0508ef; 3;
FC4s: FCP [IBM
Fabric Port Name: 20:08:00:05:1e:34:11:e5
Permanent Port Name: 50:05:07:61:00:49:20:b4
The Local Name Server has 2 entries }
8.
Enter the zoneCreate command to create the LSAN lsan_zone_fabric2, which includes the host
(10:00:00:00:c9:2b:6a:2c), Target A, and Target B.
switch:admin> zonecreate "lsan_zone_fabric2",
"10:00:00:00:c9:2b:c9:0c;50:05:07:61:00:5b:62:ed;50:05:07:61:00:49:20:b4"
PortName
10:00:00:00:c9:2b:c9:0c;
PortName
50:05:07:61:00:5b:62:ed;
DNEF-309170
F90F]
50:05:07:61:00:49:20:b4;
DNEF-309170
F90F]
NodeName
20:00:00:00:c9:2b:c9:0c; na
DV5-5.20A6 "
(yes, y, no, n): [no] y
NodeName
50:05:07:61:00:1b:62:ed; na
50:05:07:61:00:09:20:b4; na
Fabric OS 6.x administrator guide 233
TTL(sec)
TTL(sec)
Advertisement
Table of Contents
Troubleshooting
