Table of Contents
Advertisement
box 8 & 9: (figure 16)
v.
scale Bar .................................................... 1
W. Crosscut table Brace ................................. 1
X. rip Fence ................................................... 1
v
W
X
figure 16. Box 8 & 9 contents.
crate #2: (not shown)
sliding table ...................................................... 1
lock rod ........................................................... 1
locating Blocks ................................................. 2
component hardware (not shown)
t-Bolts (sliding table) M12-1.75 x 60 .............. 3
hex nuts M12-1.75 (sliding table) ................... 3
Flat Washers 12mm (sliding table) .................. 3
lock Washers 12mm (sliding table) ................ 3
Flat head screws M6-1 x 16 (Blocks) ............... 4
Cap screws M6-1 x 35 (rod) ............................ 6
lock Washers 6mm (rod) ................................ 6
push handle M12-1.75 x 12 (sliding table) ..... 1
Flat Washer 12mm (sliding table) .................... 1
t-nut M12-1.75 (sliding table) ......................... 1
set screw M6-1.0 x 12 (small table) ............... 2
Cap screw M10-1.5 x 20 (small table) ............ 2
lock Washer 10mm (small table) .................... 2
Flat Washer 10mm (small table) ..................... 2
Cap screw M10-1.5 x 20 (large table) ............ 4
lock Washer 10mm (large table) .................... 4
Flat Washer 10mm (large table) ..................... 4
g0493 14" sliding table saw
Qty
Cap screw M10-1.5 x 30 (support Brace) ........ 5
lock Washer 10mm (support Brace) ................ 5
hex nut M10-1.5 (support Brace) ..................... 3
hex Bolts M6-1 x 25 (scale Bar) ....................... 3
Flat Washers 6mm (scale Bar) ......................... 3
lock Washers 6mm (scale Bar) ....................... 3
hex nuts M6-1 (scale Bar) ............................... 3
adjustable ring w/set screw (r rail) ............... 1
end Washer 8mm (r rail) ................................ 1
lock Washer 8mm (r rail) ............................... 1
Cap screw M8-1.25 x 16 (r rail) ..................... 1
lock handles M10-1.5 x 12 (rip Fence Body) . 2
Knob M10-1.5 x 70 (rip Fence Body) ............... 1
adjustable handle M12-1.75 x 55 (Crosscut) .. 1
Flat Washer 12mm (Crosscut table) ............... 1
t-nut M12-1.75 (Crosscut table) ..................... 1
t-nut M8-1.25 (Crosscut Brace) ....................... 2
Knob M8-1.25 x 50 (Crosscut Brace) ................ 3
Flat Washer 8mm (Crosscut Brace) .................. 2
Center stud M8-1.25 x 10 (Crosscut Fence) .... 1
Fiber Washer 8mm (Crosscut Fence) ............... 1
t-Bolt M8-1.25 x 60 (Crosscut Fence) .............. 1
t-nut M8-1.25 (Crosscut Fence) ...................... 2
Knob M8-1.25 (Crosscut Fence) ....................... 1
Qty
Knob M8-1.25 x 25 (Crosscut Fence) ............... 1
Flat Washer 8mm (Crosscut Fence) ................. 1
Block (Crosscut Fence) ..................................... 1
Cap screw M8-1.25 x 35 (Crosscut Fence) ...... 1
lock Washer 8mm (Crosscut Fence) ................ 1
Button hd Cap screw M8-1.25 x 40 (guard) .... 1
Flat Washer 8mm (guard) ................................ 1
if any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
some hardware/fasteners on the inventory
list may arrive pre-installed. check mount-
ing locations on main components before
assuming inventory list items are missing.
NoTICE
-19-
Advertisement
Table of Contents
