Denon AVR-4310CI Owner's Manual page 78

Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
Audyssey Settings MultEQ XT : Corrects both time and frequency response problems in the
Set MultEQ XT, Dynamic EQ listening area.
and Dynamic Volume. • Audyssey : Optimize the frequency response of all speakers.
• Audyssey Byp.L/R : Optimize frequency response of speakers except
NOTE
front L and R speakers.
• Audyssey Flat : Optimize frequency response of all speakers to flat
If you have not performed
response.
Auto Setup, or if you change
• Manual : Apply frequency response set with "Manual EQ" (vpage
the speaker settings after
76).
performing Auto Setup, you
• OFF : Turn "MultEQ XT" equalizer off.
may not be able to select
Dynamic EQ/Dynamic
Volume, and "Run Audyssey"
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
may be displayed.
selected after Audyssey Auto Setup has been performed. "Audyssey"
In this case, either perform
is automatically selected after performing Audyssey Auto Setup. "When
Audyssey Auto Setup over
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, "
again or perform "Restore"
lights.
(vpage 33) to return to the
• After running Audyssey Auto Setup, if the Speaker Configuration,
settings after Audyssey Auto
Distance, Channel Level, and Crossover Frequency have changed without
Setup was run.
increasing the number of speakers measured, only "
• If "Dynamic EQ" or "Dynamic Volume" is set to "ON" when "MultEQ
XT" is set to either "OFF" or "Manual" , "MultEQ XT" is automatically
set to "Audyssey" .
• You can also press
NOTE
• "MultEQ XT" and "Manual EQ" cannot be selected when "EQ
Customize" is set to "Not Used" (vpage 39).
• When using headphones, "MultEQ XT" is set to "OFF".
Dynamic EQ : Solves the problem of deteriorating sound quality as
volume is decreased by taking into account human perception and room
acoustics.
• ON : Use the Dynamic EQ equalizer.
• OFF : Do not use the Dynamic EQ equalizer.
• After performing "Audyssey Auto Setup", the "Dynamic EQ" setting
automatically becomes "ON".
• " " is displayed when set to "ON".
• When "MultEQ XT" is set to "OFF" or "Manual", "Dynamic EQ" is
automatically set to "OFF".
• If "Dynamic Volume" is set to "ON", "Dynamic EQ" is automatically
set to "ON".
• When you set "Dynamic EQ" to "ON", "Tone Control" is switched
"OFF".
• You can also press

Main remote control
operation buttons
Setting contents
" lights.
[MULTEQ XT]
to set.
[DYNAMIC EQ]
to set.
:Displaying the menu
Cancel the menu
Setting items
Audyssey Settings
(Continued)
Audyssey Dynamic EQ solves the problem of deteriorating sound quality
as volume is decreased by taking into account human perception and
room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey
MultEQ ® XT to provide well-balanced sound for every listener at any
volume level.
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
"
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Setting is enabled when "Dynamic EQ" is "ON" (vpage 75).
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Setting contents
Dynamic EQ / Volume : OFF
Dynamic EQ : ON/Volume : OFF
"Red" "Off"
"Green" "OFF"
About Dynamic EQ
:Return to previous menu
See overleaf