Denon AVR-4310CI Owner's Manual page 40

Making Detailed Settings (Manual Setup)
Setting items
Surround Speaker
(Continued)
• When using the PRE OUT terminal, set to "A" or "B".
• Make the surround speaker settings when the input mode is set to "EXT.
IN" at "EXT. IN Setup" (vpage 38).
• When the "Speaker Confi guration" – "Surround A" or "Surround B"
setting (vpage 35) is "Small", and using surround speakers A and B
simultaneously, playback is with the same output as when "Surround A"
and "Surround B" are set to "Small".
Making the HDMI Settings (HDMI Setup)
Make settings for HDMI video/audio output.
Setting items
RGB Range Normal : Output with RGB video range (16 (black) to 235 (white)).
Set the video range of RGB Enhanced : Output with RGB video range (0 (black) to 255 (white)).
output from the HDMI
This setting is valid when using a TV equipped with a DVI terminal.
terminal.
Vertical Stretch ON : Expand image signal in vertical direction.
Expand image signal in OFF : Do not expand signal in vertical direction.
vertical direction.
This setting is valid with respect to the HDMI output when using an
HDMI-compatible TV. When not using an HDMI-compatible TV, it is
valid with respect to the analog output.
Auto Lip Sync ON : Compensated.
Automatic compensation OFF : Not compensated.
for timing shift in audio and
video output.
HDMI Audio Out Amp : Playback through speakers connected to the receiver.
Select HDMI audio output TV : Playback through TV connected to the receiver.
device.
When the HDMI control function is operating, the setting of audio
playback in the connected TV takes priority (vpage 80 "HDMI
Control Function").
Monitor Out Auto (Dual) : The presence of a TV connected to the MONITOR 1 or
Make settings for HDMI MONITOR 2 terminal is detected automatically, and that TV connection
monitor output. is used.
Monitor 1 : A TV connected to the MONITOR 1 terminal is always used.
Monitor 2 : A TV connected to the MONITOR 2 terminal is always used.

Main remote control
operation buttons
Setting contents
Default settings are underlined.
Setting contents
:Displaying the menu
Cancel the menu
Setting items
Monitor Out
(Continued)
• If both the Monitor 1 and 2 connectors are connected and "Resolution"
(vpage 49) is set to "Auto", the signals are output with a resolution
compatible with both TV.
• With "Resolution" (vpage 49) not set to "Auto", check whether
the TV you are using is compatible with the resolution under "HDMI
Information" – "Monitor 1" and "Monitor 2" (vpage 78).
• Depending on the monitor you have connected, the display may not be
correct when you set to "Auto (Dual)". In such a case, set to either
"Monitor 1" or "Monitor 2".
• You can also set "Monitor Out" by pressing
HDMI Control Control
External devices can be • ON : Use HDMI control function
controlled from the AVR- • OFF : Do not use HDMI control function
4310CI and the AVR-4310CI
When a device that is not compatible with the HDMI control function
can be controlled from
is connected, set "Control" to "OFF".
external devices.
NOTE
• When "Control" is set to "ON", it consumes more standby power.
• Please consult the
• When not using this unit for a long period, we recommend that you
operating instructions for
press
each connected device to
• "HDMI Control" does not work when the power to the equipment is off.
check the settings.
Either power on or set to standby.
• Refer to "HDMI Control
Standby Source : Set the HDMI connector for HDMI signal input during
Function" (vpage 80) for
standby.
more information about the
• Last : Standby with last used input source during power on.
HDMI control function.
• HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5 / HDMI6 : The standby mode
• When the "Control"
is set at the input source assigned to the respective.
setting has been changed,
always turn off the power
This can be set when "Control" is set to "ON".
to the connecting devices
Control Monitor : Set the HDMI MONITOR terminal to output the HDMI
afterwards and then turn
control signal.
back on.
• Monitor 1 : Output from the MONITOR 1 terminal.
NOTE
• Monitor 2 : Output from the MONITOR 2 terminal.
The HDMI control function
This can be set when "Control" is set to "ON".
controls operations of a
Power Off Control : The power of the AVR-4310CI and external device
TV that is compatible with
turn off together.
the HDMI control function.
• ON : Interlock.
Make sure that the TV and
• OFF : Do not interlock.
HDMI are connected when
you perform HDMI control.
This can be set when "Control" is set to "ON".
:Moves the cursor
:Confi rm the setting
(Up/Down/Left/Right)
Setting contents
[M.SEL]
<POWER>
on the main unit to turn off the power.
:Return to previous menu
.
See overleaf