Denon AVR-4310CI Owner's Manual page 39

Setting items
Distance Front L / Front R / Center / Subwoofer / Surround A L / Surround A R
/ Surround B L / Surround B R / Surr. Back L z / Surr. Back R z / Front
(Continued)
Height L / Front Height R / Front Wide L / Front Wide R : Select the
speaker.
z: When the "Speaker Configuration" – "Surround Back" setting
(vpage 35) is set to "1spkr", "Surr. Back" is displayed.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance.
• Speakers set to "None" in "Speaker Configuration" (vpage 34) are
not displayed.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 34) and "Speaker Configuration" (vpage 34) settings.
• Default settings :
Front / Center / Subwoofer / Front Height / Front Wide : 12.0 ft (3.60 m)
Surround A / Surround B / Surround Back : 10.0 ft (3.00 m)
• Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
Surround Speaker : Set the surround speakers to output the test tone.
Channel Level
• A : Output test tone from surround speakers A.
Set the volume of the test
• B : Output test tone from surround speakers B.
tone to be the same when it
• A+B : Output test tone from surround speakers A and B.
is output from each speaker.
Can be set when the "Speaker Configuration" – "Surround A" or
"Surround B" setting is "Large" or "Small" (vpage 35).
Test Tone : Output test tone.
• Front L / Front Height L / Center / Front Height R / Front R / Front
Wide R / Surround R /Surr. Back R z /Surr. Back L z / Surround L /
Front Wide L / Subwoofer : Select the speaker.
z : When the "Speaker Configuration" – "Surround Back" setting
(vpage 35) is set to "1spkr", "Surr. Back" is displayed.
• –12dB ~ +12dB (0dB) : Adjust the volume.
• Speakers set to "None" in the "Speaker Configuration" (vpage 34)
settings are not displayed.
o
• When is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
• When using surround speakers, be sure to adjust the volume of the
different speakers.
• When a headphones jack is inserted in the PHONES terminal of the AVR-
4310CI, the "Channel Level" is not displayed.
• You can also press
Volume of the Different Speakers").
Default : Reset all channel level settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Main remote control
operation buttons
Setting contents
CHANNEL LEVEL
to set (vpage 81 "Adjust the
:Displaying the menu
Cancel the menu
Setting items
Crossover Frequency 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
Outputs at below set 250Hz : Set the crossover frequency.
frequency, each speaker's
Advanced : Specify crossover frequency for each speaker.
bass signal output from
• Front / Center / Surround A / Surround B / Surround A+B / Surround
the subwoofer. Set this
Back / Front Height / Front Wide : Select the speaker.
according to the low
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
frequency reproduction
250Hz : Set the crossover frequency.
capabilities of the speakers
you are using.
• Can be set when the "Speaker Configuration" – "Subwoofer" (vpage
34) setting is "Yes", or when you have a speaker that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
• The speakers that can be set when "Advanced" is selected differ
according to the "Subwoofer Mode" setting (vpage 35).
• When "LFE" is selected, speakers set to "Small" at "Speaker
Configuration" can be set. If the speakers are set to "Large", "Full
Band" is displayed and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Surround Speaker DOLBY/DTS Cinema : Set the surround speakers to use during Dolby/
DTS Cinema mode.
Set the surround speakers
DOLBY/DTS Music : Set the surround speakers to use during Dolby/DTS
to use for every surround
Music mode.
mode.
DOLBY Game : Set the surround speakers to use during Dolby Game
mode.
DOLBY Height : Set the surround speakers to use during Dolby Height
mode.
WIDE SCREEN : Set the surround speakers to use during WIDE SCREEN
mode.
7CH STEREO : Set the surround speakers to use during 7CH STEREO
mode.
DSP SIMULATION : Set the surround speakers to use during the DENON
original surround mode.
MULTI CH MODE : Set the surround speakers to use during PCM or DSD
multi-channel mode.
• A : Use surround speakers A.
• B : Use surround speakers B.
• A+B : Use surround speakers A and B.
"Surround Speaker" is displayed when "Speaker Configuration"
– "Surround A" and "Surround B" setting (vpage 35) is set to
"Large" or "Small".
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Making Detailed Settings (Manual Setup)
Setting contents
See overleaf

:Return to previous menu