Tro_Bleshoofng - Pioneer PDP-5040HD Operating Instructions Manual

÷
TroubUesheoting
÷
No power. Make sure the Plasma Display and the Media Receiver are connected correctly. (See page 20.)
® Is the power cord disconnected? (See page 2Z)
® Has the main power been turned on? (See page 28.)
Check if you pressed TV (_) on the remote control unit (See page 28.)
If the indicator on the system lights up red press TV (_.
o Green and red rectangles appear on o Check if the system cable has been disconnected or almost disconnected? (See page 20.)
the screen alternately.
o The system cannot be operated. _ External influences such as lightning, static electricity, etc, may cause improper operation.
[n this case. operate the system af_terfirst turning the power of the Plasma Display and the
Media Receivel; or unplugging the power- cord and re-plugging it in after 1 or 2 minutes.
, Remote control unit does not
operate.
Is the Mode switch set correctly? Slide it to the TV setting position. (See page 16.)
®Are batteries inserted with polarity (+, -) aligned? (See page 22.)
Are batteries worn out? (Replace with new bafteries.) (See page 22_)
® Operate the remote control unit while pointing it toward the remote control sensor on the
Plasma Display. (See page 1Z)
Are you using it under strong or fluorescent lighting?
o Is a fluorescent light illuminated near the remote control sensor?
o No image and audio is presenteG
® Check if the input source for video or PC has been unintentionally selected although you want
to watch a TV channek (See page 50.)
Check if you have activated the Parental Control function. (See page 90.)
Enter a password to temporarily cancel the Parental Control function, (See page 94,)
No picture.
Is connection to other components correct? (See pages 65 to 7Z)
® is the correct input selected? (See pages 16, 6.5 to 7Z)
is a non-compatible PC signal being input? (See page IOZ)
® Is picture adjustment correct? (See pages 48 to .52,)
o Images are presented but no audio
is outpu£
® Check if you have selected the minimum volume, (See page 51 .)
Check if you have muted sound, (See page 51 _)
®When using a video or PC input source, check that the audio terminal is atso in connection. (See
pages 65 to 67 and 7Z)
Sound is reversed between the right
and left.
Sound is output from only a single
speaker:
o Picture is cut off.
Check if the speaker cable connections have been reversed between the right and lef# or if the
speaker cable from either speaker has been disconnected. (See pages 15 and 20,)
® Has the balance been correctly adjusted? (See page 52,)
Is the image position correct? (See pages 8! and 82.)
Has the correct screen size been selected? (See page 85,)
o Strange colour, light coloui; dark or
colour misalignment,
Power is suddenly turned off.
Adjust the pkture tone, (See pages 48 to 52.)
Is the room too bright? The picture may look dark in a room that is too bright,
Is the sleep timer set? (See page 85.)
Check the power control setting. (See pages 54 and 55,)
®The system's internal temperature has increased, Remove any objects blocking vent or clean,
(See pages 17 to 19.)
÷
SD04 Powering ofT. Internal temperature too high, Check if the ambient temperature of the Plasma Display is high,
Check temperature around PDP
SD05 Powering of[ Internal protection cimuits activated, Check the speaker cable connections between the Plasma Display
is there a short in speaker cable? and the speakers.
SDll Powering ofT. internal temperature too high. Check if the ambient temperature of the Plasma Display and the
Check temperature around media receive_ Media Receiver is high.
En
PDP5040H D-Eng (106-109) 106 _ 7/24/03, 1:57 PM