Table of Contents
Advertisement
240
SAFETY
Activating SSC
Once SSC is enabled it will activate automatically once
the following conditions are met:
•
The driver releases the throttle.
•
The driver releases the brake.
•
The driver seat belt is buckled.
•
The transmission is in any selection other than
PARK.
•
Your vehicle speed is below 20 mph (32 km/h).
•
The driver door is closed. (If doors are attached, the
door must be closed. If doors are detached, the
driver seat belt must be buckled).
The set speed for SSC is selectable by the driver, and
can be adjusted by using the gear shift +/-. Additionally,
the SSC set speed may be reduced when climbing a
grade and the level of set speed reduction depends on
the magnitude of grade. The following summarizes the
SSC set speeds:
SSC Target Set Speeds
•
1st = 0.6 mph (1 km/h)
•
2nd = 1.2 mph (2 km/h)
•
3rd = 1.8 mph (3 km/h)
•
4th = 2.5 mph (4 km/h)
•
5th = 3.1 mph (5 km/h)
•
6th = 3.7 mph (6 km/h)
•
7th = 4.3 mph (7 km/h)
•
8th = 5 mph (8 km/h)
•
9th = 5.6 mph (9 km/h) — if equipped
•
REVERSE = 0.6 mph (1 km/h)
•
NEUTRAL = 1.2 mph (2 km/h)
•
PARK = SSC remains enabled but not active
SSC Target Set Speeds — If Equipped With Off Road+
•
1st = 0.6 mph (1 km/h)
•
2nd = 0.9 mph (1.5 km/h)
•
3rd = 1.2 mph (2 km/h)
•
4th = 1.5 mph (2.5 km/h)
•
5th = 1.8 mph (3 km/h)
•
6th = 2.5 mph (4 km/h)
•
7th = 3.7 mph (6 km/h)
•
8th = 5 mph (8 km/h)
•
REVERSE = 0.6 mph (1 km/h)
•
NEUTRAL = 1.2 mph (2 km/h)
•
PARK = SSC remains enabled but not active
NOTE:
•
During SSC, the +/- gear selector input is used for
SSC target speed selection but will not affect the
gear chosen by the transmission. While actively con-
trolling SSC, the transmission will shift appropriately
for the driver-selected set speed and corresponding
driving conditions.
•
SSC operation is influenced by Off Road+ drive
mode if active. The differences may be notable to
the driver as a varying level of aggressiveness.
Driver Override
The driver may override SSC activation with throttle or
brake application at any time.
Deactivating SSC
SSC will be deactivated but remain available if any of
the following conditions occur:
•
The driver overrides SSC set speed with throttle or
brake application.
•
The vehicle speed exceeds 20 mph (32 km/h) but
remains below 40 mph (64 km/h).
•
The vehicle is shifted into PARK.
Disabling SSC
SSC will deactivate and be disabled if any of the follow-
ing conditions occur:
•
The driver pushes the SSC switch.
•
The driveline is shifted out of the 4WD Low.
•
The parking brake is applied.
•
The vehicle is driven greater than 20 mph
(32 km/h) for greater than 70 seconds.
•
The vehicle is driven greater than 40 mph
(64 km/h). SSC will exist immediately.
•
The driver door opens. (Driver door opens if doors
are attached or driver seat belt is unbuckled if doors
are detached).
Feedback To The Driver
The instrument cluster has an SSC icon and the SSC
switch has a lamp that offers feedback to the driver
about the state SSC is in.
•
The cluster icon and switch lamp will illuminate and
remain on solid when SSC is enabled or activated.
These are the normal operating conditions for SSC.
•
The cluster icon and switch lamp will flash for sev-
eral seconds then extinguish when the driver
pushes the SSC switch but enabled conditions are
not met.
•
The cluster icon and switch lamp will flash for sev-
eral seconds then extinguish when SSC disables
due to excess speed.
•
The cluster icon and switch lamp will flash then
extinguish when SSC deactivates due to overheated
brakes.
Advertisement
Table of Contents
