Table of Contents
Advertisement
B. Basic Copying Operation
1) Set the power switch to ON (I).
(1) If the temperature
of the fixing roller
is too low for copying, the indicator
of the COPY START key will glow red.
(2) When the temperature
of the fixing
roller becomes high enough for copy-
ing, the indicator will glow green.
(3) The normal
waiting
time
at room
temperature
(20°C)
is about
70
seconds.
2) Raise the copyboard
cover, place an
original on the copyboard with the side
to be copied
facing
downward,
and
align it with the size indication.
3) To adjust the copy density manually,
the A key indicator should be OFF; press
the key once if it is ON. Set the COPY
DENSITY cursor to suit the original.
4) Check the size of paper in the cassette.
(1) If the cassette
does not have the
desired size of paper, remove it and
install a cassette
with the desired
size.
5) Set the required number of copies (1 to
99) using the number keys and confirm
that the correct number appears on the
COPY NUMBER indicator.
(1) If an error was made in inputting the
number
of
copies,
press
the
CLEAR/STOP
key and reset the num-
ber of copies.
6) Press the COPY START kev.
iI)
(2)
To stop a continuous copying opera-
tion, press the CLEAR/STOP
key. The
copier will complete the copy in prog-
ress, then stop.
The COPY
NUMBER
indicator
will
display the initially set copy quantity.
It is possible to switch from auto-
matic
exposure
control
to manual
density adjustment
at any time from
the start of copying to the completion
of the final copy. However, it is not
possible to switch in the other direc-
tion from manual density adjustment
to automatic.
Example:
If the copy is too dark or too faint using AE,
cancel AE and vary the copy density with
the COPY DENSITY cursor.
(3) If the PAPER OUT indicator goes ON
I
(4)
(5)
during copying, the copier will stop.
Refill the
cassette
and
press the
COPY
START
key. The
remaining
number
of copies
will
be
made
automatically.
If the copier has a DF, place a docu-
ment (original) on the document tray.
The document will be fed automati-
cally and copying will start.
If no other operation
is performed,
the copier will return to the STAN-
DARD
mode approximately
2 min-
utes after it completes a copy or after
the last key operation.
l-8
COPYRIGHT
0
ISSO
CANON INC.
C. MANUAL
FEED PICK-UP OPERATION
1) Place an original on the copyboard.
2) Select manual or AE density control.
3) Feed one sheet of copy paper into the
copier along the guides of the manual
feed tray.
(1) When the copier senses the paper,
copying will start automatically.
(2) When
performing
continuous
man-
ual feed copying, keep the sheets at
least
50
mm separate
from
each
other.
Note:
Manual feed copying is possible when the
PAPER OUT indicator is ON and the COPY
START key is glowing red.
D. TWO-SIDED
COPYING
Copy one side of a 2-sided
original.
Invert the original so that the same edge
faces the front. Invert the copy in the same
way (front edge facing front ward) and feed
it into the copier.
(1) Use dry, uncurled paper.
(2) Use
paper
in the weight
range
60
128g/m'.
(3) When
making
two-sided
copies,
only
oneimagecanbemadeoneachsideof
the copy paper.
(4) Overlay and two-sided copies cannot be
made on the same sheet of copy paper.
E. OVERLAY
COPY OPERATION
By changing the developing
unit, a 2-
color copy can be made on the same side
of the copy paper.
y;;oT;y,er
in the ,range
of 60
to
(1)
(2)
(3)
When making an overlay copy a maxi-
mum of two images can be made on one
side of the copy paper.
Overlay and two-sided copies cannot be
made on the same sheet of copy paper.
Figure 1-5
CANON NP.1015/1215S
AN.0
OCT.
1988 PAINTEA
IN JAWI
IlMPillMf
AU JAPON)
Advertisement
Table of Contents
