Maintenance - 3M PELTOR PIC-100 NA User Instruction

EN
Problem
Pairing failed.
Transmission
does not start
when pressing
the PTT button.
Transmission
does not start
when I start to
talk.
I do not hear
any sound from
the earplugs.
I cannot hear
any sound out
of one earplug
My outbound
radio
transmission
sounds
distorted. My
close-connect
team members
complain that
they can't
understand me
when I talk.
Battery pack
LED light does
not illuminate
when charging.
I get an audio
prompt that my
calibration
status is
"unknown".
15. STORAGE AND DISPOSAL
15.1. STORAGE
• Always store the PIC-100 headset in a clean area.
• Clean the product before storage.
• Examine the product for wear or damage.
• Keep the product in a clean and dry area (<90% humidity)
within a temperature range of -20°C/-4°F to 40°C/104°F.
• Do not put the product in sunlight during storage.
18
FP3881REVA_6sidedcover_32sidedinserts_4 x 6_2022-08-24.indd 18 FP3881REVA_6sidedcover_32sidedinserts_4 x 6_2022-08-24.indd 18
Possible Issue/Solution
Make sure the Bluetooth device to pair
®
is set to pairing mode and ready for
pairing.
The Bluetooth device to pair is out of
®
range.
The SCU is set for VOX operation.
Double press the PTT button and listen
for an audio message that confirms the
PTT mode is selected.
The SCU is set for PTT operation.
Double press the PTT button and listen
for an audio message that confirms the
VOX mode is selected.
The headset is not connected to the
SCU.
Connect the headset connector to the
socket in the SCU.
There is a headset cable problem.
Replace the headset.
Eartip may be folded. Check to see if
eartip is folded onto itself; reinsert.
Eartip opening may be blocked. Check
the eartip for blockage, replace if
blocked. Refit and fit test.
Your hearing protectors may not be
properly fitted which can interfere with
sound clarity.
Refit your hearing protectors and conduct
a real-time fit test to check your fit.
The battery is out of the recommended
charging temperature range. Bring the
battery pack to room temperature and try
charging again.
The SCU likely requires service to
replace a faulty coin cell. Contact 3M
Technical Assistance for support.
15.2. DISPOSAL
• Obey national regulations.
• To properly dispose of the battery, follow local solid waste
disposal regulations.
• Use the local recycling system for electronic equipment.
15.2.1. BATTERY DISPOSAL
Many rechargeable batteries are required to be recycled by local,
state/province, and national laws. To properly recycle/dispose of
the battery or battery pack, always follow local solid waste disposal
regulations.
Additionally in the United States and Canada, 3M Company is
partnering with Call2Recycle (RBRC) to provide recycling service
to you to help ensure that the rechargeable batteries within our
products are recycled properly. To assist you in using this service
call the Call2Recycle battery recycling information help line at
1-800-8-BATTERY (1-800-822-8837) or consult Call2Recycle's
battery recycling guidance online at www.call2recycle.org.
16.

MAINTENANCE

Examine the earplugs regularly for damage. A damaged earpiece
or dirty and/or damaged eartips must be replaced. Refer to chapter
17. ACCESSORIES.
16.1. TO CLEAN THE PRODUCT
16.1.1. PIC-100 HEADSET EARPIECES
• Clean the earpieces with a lightly damp cloth.
NOTE: Do not immerse in water.
16.1.2. 3M™ ULTRAFIT™ EARTIPS
• Clean eartips with warm water and soap as needed.
• Look for tears or cracks under any of the flanges. Replace as
needed.
16.1.3. 3M™ SKULL SCREW™ COMMUNICATION
EARTIPS AND 3M™ PELTOR™
CCC-GRM-25 EARTIPS
• Clean by wiping with a clean, dry cloth.
• Replace the eartip if the eartip is damaged.
• Replace the eartip if it is detached from the stem.
• Replace the eartip if the eartip is not soft and pliable.
16.1.4. SCU
• Clean the SCU with a lightly damp cloth.
NOTE: Do not immerse in water.
• To maintain water resistance capability, the gasket surrounding
the battery contacts must be kept free of dirt and other
materials that would prevent proper mating of the battery.
16.2. CALIBRATION
The first time that the PIC-100 headset is plugged into the SCU
and powered on, the two-year calibration cycle begins. You will be
reminded to replace your headset with a new calibrated headset
beginning 90 days prior to its expiration and periodically thereafter.
To hear when a new calibrated headset is due, refer to 12.13.
SOFTWARE VERSION.
2022-08-24 08:30:30 2022-08-24 08:30:30