Suspended Ceiling Adjustable T-Rail Clips - Cisco Aironet 1130AG Series Hardware Installation Manual

2 8 2 8
Chapter 2 2 Chapter Installing the Installing

Suspended Ceiling Adjustable T-Rail Clips

Suspended Ceiling Adjustable T-Rail Clips
OL-8369-04 OL-8369-04
the Access Access Point Point
The accessory kit contains two suspended ceiling adjustable T-rail clips; one for standard ceiling tile The accessory kit contains two suspended ceiling adjustable T-rail clips; one for standard ceiling tile
rails and the other for recessed ceiling tile rails. The clips are adjustable to accomodate three standard rails and the other for recessed ceiling tile rails. The clips are adjustable to accomodate three standard
T T -rail widths. Each cli -rail widths. Each cli p contains detents that p contains detents that are used to adjust the
markings that indicate the T-rail width and the hole letter that corresponds to the correct mounting ho markings that indicate the T-rail width and the hole letter that corresponds to the correct mounting ho les
on the mounting plate. Fi Figur on the mounting plate.
F F i i g g u u r r e e 2 2 - - 3 3 T T - - R R a a i i l l C C l l i i p p F F e e a a t t u u r r e e s s
2 2
3 3
3 3 8 8 2 2 4 4
MM MM
INCH INCH
1 1 - - 1 1 / / 2 2 1 1 5 5 / / 1 1
CEILING CEILING
GRID GRID A A B B
WIDTH WIDTH
2 2
1 1
T T -rail locking -rail locking screws screws
2 2
Mounting plate screw holes Mounting plate screw holes
(8 x 32 flat head screw) (8 x 32 flat head screw)
The adjustable T-rail clip attaches to the mounting plate using four 6 x 32 x 1/4 inch The adjustable T-rail clip attaches to the mounting plate using four 6 x 32 x 1/4 inch
The A, B, and C holes on the T-rail clips and the mounting plate correspond to these T-rail widths: The A, B, and C holes on the T-rail clips and the mounting plate correspond to these T-rail widths:
• • A holes—used for 1 1/2 in (38 mm) T-rails A holes—used for 1 1/2 in (38 mm) T-rails
• • B holes—used for 15/16 in (24 mm) T-rails B holes—used for 15/16 in (24 mm) T-rails
• • C holes—used for 9/16 in (15 mm) T-rails C holes—used for 9/16 in (15 mm) T-rails
are used to adjust the clip to the T-rail. Each detent contains
gure e 2- 2-3 3 shows the details of the adjustable T-rail clips. shows the details of the adjustable T-rail clips.
1 1
1 1 5 5
6 6 9 9 / / 1 1 6 6
C C
C C B B
6 6 1 1 / / 9 9 6 6 1 1 / / 5 5
5 5 1 1 4 4 2 2
1 1
3 3
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Deploying the Access Points on the Wireless Network Deploying the Access Points on the Wireless Network
clip to the T-rail. Each detent contains
2 2
H H T T D D I I W W
A A
D D I I R R G G
G G N N I I L L I I E E C C
1 1 2 2 / / 1 1 - - 1 1
H H C C N N I I
M M M M
8 8 3 3
3 3
2 2
8 8
5 5
7 7
1 1
2 2
1 1
T-rail width adjustment detents (A, B, C) T-rail width adjustment detents (A, B, C)
correspond to the A, B, and C holes on the correspond to the A, B, and C holes on the
mounting plate mounting plate
Point Hardware Installation Guide
les
flat head screws. flat head screws.