Inline Power Status Messages - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
3-6 3-6
Chapter 3 3 Chapter Troubleshooting Troubleshoo
Note Note
Tip Tip

Inline Power Status Messages

Inline Power Status Messages
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
The access point supports Intelligent Power Management and as a result of the power negotiations, the The access point supports Intelligent Power Management and as a result of the power negotiations, the
access point will either enter full power mode or remain in low power mode with the radios disabled. access point will either enter full power mode or remain in low power mode with the radios disabled.
Independent of the power negotiations, the access point hardware also uses the 802.3af classification Independent of the power negotiations, the access point hardware also uses the 802.3af classification
scheme to indicate the power required from the power source. However, the power source cannot report scheme to indicate the power required from the
the power available to the access point unless the power source also supports Intelligent Power the power available to the access point unless the power source also supports Intelligent Power
Management. Management.
Some Cisco switches that are capable of supplying sufficient power require a software upgrade to Some Cisco switches that are capable of supplying sufficient power require a software upgrade to
support Intelligent Power Management. If the software upgrade is not desired, you can configure the support Intelligent Power Management. If the software upgrade is not desired, you can configure the
access point to operate in pre-standard compatibility mode and the access point automatically enters full access point to operate in pre-standard compatibility mode and the access point automatically enters full
power mode if these Cisco switches are detected in the received CDP ID field. power mode if these Cisco switches are detected in the received CDP ID field.
When the access point determines that sufficient power is not available for full power operation, an error When the access point determines that
message is logged and the Status LED turns amber to indicate low power mode (see the "Checking the message is logged and the Status LED turns amber to indicate low power mode (see the
Autonomous Access Point LEDs Autonomo us Access Point
on p on page age 3- 3-7 7 ). ).
If your switch is capable of supplying sufficient power for full operation but the access point remains in If your switch is capable of supplying sufficient power for full operation but the access point remains in
low-power mode, your access point or yo low-power mode, your access point or yo ur switch (or both) might be misconfigured (see
T T able abl e 3-3 3-3). ).
If your inline power source is n ot able to supply sufficient power for full operation, y If your inline power source is n
these options: these options:
• • Upgrade to a higher-powered switch Upgrade to a higher-powered switch
• • Use a Cisco Aironet power injector on the switch port Use a Cisco Aironet power injector on the switch port
• • Use the 48-VDC power module to locally power the access point Use the 48-VDC power module to locally power the access point
These messages are logged on the console port by the access point to report the power condition: These messages are logged on the console port by the access point to report the power condition:
• • %CDP_PD-4-POWER_OK: Full Power - AC_ADAPTOR inline power source—This message %CDP_PD-4-POWER_OK: Full Power - AC_ADAPTOR inline power source—This message
indicates the access point is using the power module and can support full-power operation. indicates the access point is using the power module and can support full-power operation.
• • %CDP_PD-4-POWER_OK: Full Power - NEGOTIATED inline power source—This message %CDP_PD-4-POWER_OK: Full Power - NEGOTIATED inline power source—This message
indicates the access point is operating at full power and has successfully negotiated for 12.95 W of indicates the access point is operating at full power and has successfully negotiated for 12.95 W of
power from a Cisco switch supporting Cisco Intelligent Power Management. power from a Cisco switch supporting Cisco Intelligent Power Management.
• • %CDP_PD-4-POWER_OK: Full Power - HIGH_POWER_CLASSIC inline power source—This %CDP_PD-4-POWER_OK: Full Power - HIGH_POWER_CLASSIC inline power source—This
message indicates the access point is operating at full power because it has been configured for message indicates the access point is operating at full power because it has been configured for
pre-standard compatibility mode and has detected a Cisco switch that does not support Intelligent pre-standard compatibility mode and has detected a Cisco switch that does not support Intelligent
Power Management but is able to supply sufficient power to the access point. Power Management but is able to supply sufficient power to the access point.
• • %CDP_PD-4-POWER_OK: Full Power - INJECTOR_CONFIGURED_ON_SOURCE inline power %CDP_PD-4-POWER_OK: Full Power - INJECTOR_CONFIGURED_ON_SOURCE inline power
source—This message indicates the access point is operating at full power because it is connected source—This message indicates the access point is operating at full power because it is connected
to a Cisco switch that supports Intelligent Power Management and the switch has been configured to a Cisco switch that supports Intelligent Power Management and the switch has been configured
with the powe with the powe r in r inline line never never command.
• • %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_CURRENT_PORT %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_CURRENT_PORT
inline power source—This message indicates the access point is operating at full power because it inline power source—This message indicates the access point is operating at full power because it
has been configured to expect a power injector on this port. has been configured to expect a power injector on this port.
power source. However, the power source cannot report
sufficient power is not available for full power operation, an error
LEDs" section on page " section on page 3-2 and the 3-2 and the "Inline Power Status Messages" section
ur switch (or both) might be misconfigured (see T
ot able to supply sufficient power for full operation, y ou should consider
command.
Low Power Condition for Autonomous Access Points Low Power Condition for Autonomous Access Points
"Inline Power Status Messages" section
ou should consider
OL-8369-04 OL-8369-04
"Checking the
T able abl e 3-2 and 3-2 and